Just replaced the spark plugs and coils yesterday, today it gives P0113 code, Intake air temperature (IAT) sensor - high input Wiring open circuit/short to positive, ground wire defective, IAT sensor, ECM...
View 3 RepliesI did a valve job on a 2002 Santa re 2.7 after I got it done and all back together I don't have and spark at the coils all of them are dead I'm sure the coils did go bad form sitting.
View 2 RepliesMy 2004 honda accord will not start, there is no power to the spark plugs or to the coils.
View 3 RepliesSo the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
Here's the run down:
-bought 6 months ago for cheap because it wouldn't pass smog test
-changed Purge Control Valve (PCV) and it passed
-filled with gas, heard popping noises like a backfire, and coded it read the same "Bank 1 and Bank 2 running lean, like it did before the PCV and then also "Cylinder 3 Misfire" appeared.
-At this point the car started running rough, at idle, and through acceleration...sputtering uphill, and when climbing through the gears.
-Changed the plugs & wires
-NOW, it's cylinder 5 misfiring, and not nearly as bad. It's idling and running rough, acceleration has somewhat come back, but it's definitely not 100%.
Should I start with the PCV again, since it's not starting after I fill the tank, and climbing gears slow? Is there anything else I should be checking?
My '07 had the check engine come in the other day, engine misfire. I took it to the dealer hoping it was a coil, due to the 100,000 mi warranty from Ford I was hoping would be covered. Sadly, and of course, all coils tested fine, turns out 2 plugs were bad. They replaced all 8 plugs, plus a plug boot. Not one plug broke (truck had 80k on it) so no extra cost there. So much more, but peace of mind that all the plugs are new one piece plugs is great. He recommended that they should be replaced every 60k to avoid any issues.
View 7 RepliesI have a 2005 Jeep Liberty with about 129K. The car overheated and resulted in changing the head gasket and piston rings. Now the car will not start with all six spark plugs installed. It will only start and run for a short period time with three spark plugs on the driver side installed.
View 19 RepliesI have 06 XLS with 56,000 miles and about 3 weeks ago the check engine and VSC lights came on. It was fixed, a ignition coil on the 4 cylinder.
Now driving home today the check engine and VSC lights are on again! I was wondering should try to get the dealer to replace all the remaining ignition coils ?
Plus I read their was some type of manufacturer defect on the original ignition coils from the factory. Why Toyota won't recognize this issue ?
Two ignition coils in a little over a month . My first Toyota and I'm rolling with the punches .
I have a 2001 saturn sl 2 and I noticed some oil around all the spark plugs. The engine seems to be loosing oil a little bit as well, about a quart a week. Its not buring it or leaking that I noticed.
View 2 RepliesThis past Sunday, I replaced the spark plugs on my 2008 Toyota Camry CE, following one of the sticky DIYs. My car has approximately 107,xxx miles.
Last night on my drive home from work my CEL came on. First time seeing a CEL light since my BMW days, . Luckily, I have a OBDII scanner at home and after running the scanner, it gave me the following trouble codes:
- P0101
- P0172
I went ahead cleaned the air filter (I have an Injen SRI installed).
After doing some research on the interwebs, I have concluded that this code has to do with the MAF. Time permitting, I am going to clean the MAF sensor later tonight. In the meantime I reset the CEL, to see if it will come on again.
My only question, which I am unable to find an answer to, is:
Can there be a possibility that the P0101 and P0172 trouble codes be related to me replacing the spark plugs, or is this just a mere coincidence?
So my mom recently bought a 2003 Elantra (75K miles, auto trans) and within a few days the CEL came on. She took it in to PepBoys and had them hook it to their scanner to get the codes out of it. The only code that came up was P0113 Intake Air Temp (IAT) Sensor high input. I've done a little research on the net but there is a lot of random info for this code out there. Is the IAT a separate sensor or is it combined in with the Mass Air Flow (MAF) sensor(if this car even has a MAF) or combined in with the MAP sensor? I've read on the net that it could be any of these 3, I think it's combined into the MAP.
I've also read that this code could be caused by a bad IAT, bad O2 sensor, an exhaust leak, bad wiring/ground(I checked the wiring/grounds visually and everything seems ok) or many other things. If it's as simple as replacing one of the sensors I can do that myself, I just don't want to go randomly buying things and either it be the wrong part or have it be the right part but not fix the problem. The car runs great, even with the CEL on. Yesterday when she stopped by my house I disconnected the battery for a couple minutes and reconnected it, started the car & no CEL. She drove the car for about 125-150 miles before the light came back on.
I have a very well maintained 2005 honda odyssey with 150,000 miles on it. It typically gets 22 m.p.g. It started using an unusual amount of gas - was getting 12 m.p.g. Took it to the mechanic and turned out the gas pump was cracked. We replaced the gas pump and the gas line, and it was getting 14 m.p.g. Took it to another mechanic, and he said that the spark plugs were the problem as they were not official Honda spark plugs (we replaced them at around 110,000 miles). So we installed the official Honda spark plugs, but still no good. I have visited several mechanics and no one seems to know.
View 7 Replies2005, 2.7l. FWD automatic, with 180,000+ miles.
A week ago it started making a random ticking noise I've never heard before. Today was the first chance I got to try and find it and I'm stumped on what could cause this.
The sound is a static or low voltage electrical discharge coming off the harmonic balancer. I can actually see the blue spark occurring at random intervals and locations on the balancer as the car is running.
Do i need to be looking for a bad engine ground? I'm having no other electrical problems. The car runs like a champ other than a minor oil and power steering fluid leak.
I have a 2003 Elantra GLS. I am intermittently Check Engine light and error code is P0113 - Air Intake sensor issue. I can't locate where the sensor is. I don't see any wire coming of the tubing that connects the air filter to the engine.
View 18 Replies2001 LS v8 .... What would cause the car to give off a strong smell after changing the plugs?
View 5 RepliesI have a 2001 Ford Expedition with the 5.4L engine. I know that there are problems with the engines blowing out spark plugs. Besides putting in sleeves and replacing the cover when necessary, any good luck with a different alternative. If not what products with the above options seem to give you the most bang for your buck.
View 16 RepliesI am changing my own spark plugs for the first time. I have a spark plug wrench, dielectric grease, anti-seize compound etc.
I have a Haynes manual for my 2002 Toyota Corolla. The book was written before Irridium plugs were used. Should I tighten the spark plugs to the same torque specifications as regular plugs? The book says 158 inch pounds. How do I know I have tightened them to the right amount?
How do I avoid cross threading the spark plugs? What happens if you cross thread the spark plugs (assuming the car seems to be running fine)? Would I need a new engine or expensive repair when it is time to replace the spark plugs again?
How do I take off the gear shift knob? I want to replace it with an aftermarket one.
View 1 RepliesGetting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
I have rough idle problem after changing spark plugs, fuel filter and battery. There was no rough idle problem before this work was done. What could be wrong. Once the speed is above 20 mph it seem to run fine but at stops it vibrates and seem like it may stall!
View 6 RepliesI just replaced the motor in a 2002 Sante Fe 2.7 due to timing belt breaking, this motor will not start, it turns over, but I am getting no fire to the coils. Crank sensor replaced waiting on the cam sensor, anything else it could be?
View 2 Replies