My santa fe has been great but recently after putting fuel in, it does not seem to want to start.turns over and runs for a couple seconds then dies out. Have to keep accelerator pushed down for it to keep running. after that it seems to run and crank ok. Why it keeps dying out after fueling?
View 4 RepliesMy wife and i have an 07 accent 2 door and we have a very hard time starting the car after putting fuel in it. Tank level doesn't seem to affect this issue. The car has 160,000 km on it. I've replaced the coil packs already twice. After getting the car to start after putting fuel in it it struggles at idle for the first 15-30 sec and then bang problem is gone until the next time i put fuel in it.
View 2 RepliesMy 2005 Santa Fe w/ 2.7L V6 started a strange symptom recently. Not always but often after its been turned off for awhile when I turn the key to the on position you can hear a fairly loud rushing noise while you inside the vehicle. With the heater/blower/radio and everything else turned off you can hear what sounds like fluid rushing or growling noise when you turn the key to the on position before starting the engine. It times off after a few seconds about the same interval as the fuel pump run time. It sounds just like fluid gushing and everyone inside the cabin can noticeably hear it.
Now I realize the the fuel tank and the fuel pump assembly are positioned under the vehicle in the same area as the back seat and I believe the access plate to the fuel pump assembly is directly under the drivers side backseat's bottom cushion. So it makes sense that any noise inside the fuel tank would be noticeable from inside the cabin. So far the vehicle has no drivability issues. But intermittently after the vehicle has been off for awhile the noise reappears at key on position. It sounds as if when the key is turned to the on position the fuel pump priming is causing turbulence and flushing fuel around in the tank. Yet it starts and drives normally. I've had this vehicle since it was brand new and I know of many issues that these Santa Fe's have but this new to me.
Drove the vehicle today (current at 156k miles) about 40 miles then came back home. Left again to run an errand. After coming out of the store and starting the car, a very pronounced 'whine' occurred. It kept whining for about 2 miles and with 3 blocks left to go, the whine suddenly stopped. No CEL appeared and the radiator temp was normal, oil level was fine and the pwr steering fluid in the reservoir was at the max level. I suspected it might be the p/s pump but, if so, why did the noise cease?
View 1 RepliesI have a 2.4 Petrol, 16 valve engine in my Santa Fe which produces a rattle on startup when cold. When warm it starts normally. Oil and filter change makes no difference. Timing belt changed 40K ago. No other effects felt with regard to power or noise once initial noise/rattle has stopped after 2 to 4 seconds.
View 4 RepliesMy car has three codes P0102 - MAF or VAF Low Circuit Input, P0030 & P0050 which are signaling O2 sensor issues.
Car symptoms are a hiccup type sputter when accelerating for the first few times after starting the vehicle. The RPMs will drop down under 1000rpm and it will come back without taking my foot off the gas. The power comes back faster if I flutter the pedal. The last few times it stalled while taking off.
After the car is warm, it runs better smoother. I'm also noticing slightly poor fuel economy. The exhaust smells rich to me.
I'm wondering if there is a fuse that could cause all three codes? Seems like a power problem? Where is the fuse for these sensors?
Should I replace MAF? Can I use the MAF from a 2004 2.4L engine that's at the junk yard? How to proceed.
Santa fe 2.7litre 2004 240000km... My santa fe won't start, after check we found no power at the fuel pump. we change pump, we found a bad contact at the remote starter connection. we decide to cut the wires of remote starter. after the car start and ride 1 day, stop with check engine, towing
We take off the remote starter and disconnect all wire of this remote starter. The car start and stop. After that bizarre problem, the park light stay open, and the window can be up and don't with no key in the ignition!!!!
We check fuse relay etc, all wire of the old remote starter and we take off battery and rebuilt the ground. We still have the same problem; when we tried to start at acc, everything seam normal but the wipers run at off position and when we turn the key for starting , wiper stop , radio close.
Like we have a ground problem. We change the ignition little baril now we think the computer is maybe dead. I double check all remote starter wire and every thing seem ok !!!!!
My 04 elantra starting acting up yesterday. It has started jumping/ rocking entire car when putting in to reverse. What might cause this problem. It is hard to describe what it is doing being I know nothing about cars. It is a large jolt when going into reverse.
View 4 RepliesNo codes, transmission makes a slight grinding noise when putting it into reverse only. Has a slight bump from 1st to 2nd. I flushed 16 quarts of the sp3 through it. Been researching and see a lot of talk about the output and input sensors. Not my car but my sisters. Needs axles, timing belt water pump, ps return hose, plus have champions in there and old ass hyundai wires.... thing does idle rough, motor mounts are new.
View 1 RepliesWhen I get gas in my '04 Sante fe it can be very hard to get it restarted. It acts as though its flooded.
View 9 RepliesI drive a 2004 Hyundai Santa Fe V6 2.7L with a whopping 274,3xx miles on it. I've had it for about 6 years and it has been a great car for the most part. The water pump was replaced a couple years ago and the battery was replaced a year ago.
It started having issues a few months ago. It started out having difficulty starting, and shortly after it would start it would rev up as if you were accelerating even if my foot was on the brake. I took it to the shop and they checked the head gaskets, battery, transmission, alternator (I think?). Came up with the idea that it may be the air intake valve. It's the thing that controls how much the blade opens when you press on the accelerator. Well they took it out and said it was the dirtiest one they had ever seen. They cleaned it, because no one in our area had a replacement, and my car seemed to be acting better. It would still rev occasionally and would have trouble starting but not nearly as often as before.
Fast forward to now (a month later) and my car is revving higher and for longer than it ever has and has started stalling, and not starting more frequently. It usually stalls after it has been revving when it cant release or go forward (ex. when applying the brake or while in park.)
What the heck is wrong with this thing?? No one seems to be able to figure it out and it it so frustrating, not to mention dangerous! It stalled in the middle of me making a turn today so I was literally sitting in the middle of oncoming traffic with a dead car.
My 2005 Santa Fe needs a purge valve.
View 3 RepliesEarlier this week, noticed that my car was surging on its own; basically, if I came to a stop, I could still feel the engine, like it wanted to just take off. And if I would have taken my foot off the pedal, it would have done just that. Also, I knew the car had gas, but sometimes, when starting the car it would not start at all. I would have to wait about 5 minutes or so and add major gas to it with the pedal and then finally it would engage. And then the last thing was that when I would get to my destination and put it in Park, the RPMs would go up to about 1500 or so, maybe a bit higher and then stay there and go back down to about 1000, without me pressing on the gas pedal at all. So anyway, thought it was the throttle position sensor, so I had my Dad install a new one on the car. It was a pretty easy process and thought that took care of the problem.
The surging part basically stopped, so the new TPS took care of that, but then it still had problems with starting. Took it to a car repair place the next day and they changed out the spark plugs, said that they were causing a misfire in the engine. Also changed ignition wires and a new gasket. So after they were done, drove away and all seemed to be fine, but then went to the dentist and Parked and then the RPMs went up again. Tried to start it immediately afterwards and it wouldn't start again. Tried a few minutes later, added gas with the pedal and it did start. Took it back to the car repair place, they drove it around, inspected everything and everything checked out fine. (Yeah, of course!) Ok, so just thought maybe the repairs were taking a bit to take effect. But later in the day, wouldn't start again.
So next morning, took it to the Hyundai dealer. They looked at everything for about 2 hrs, and said that there was a vacuum hose that was leaking, so they put on a new clamp but everything else checked out okay. Ok, so now it starts fine every time, but today it did that high RPM thing again when I put it into Park. It doesn't do it every time, but the RPM will just go up randomly then go back down and go back to normal. Should I clean the IAC with some type of carb cleaner to get out any carbon deposits? Or could it be a bad MAF sensor? Not sure what the symptoms are of that. Everything else seems to be okay now except for the random high RPMs when in Park and sometimes at startup too.
It's a 2 WD, V6 engine.
First I have to say my Santa Fe is my pride and joy, never have I enjoyed a vehicle so much but today I encountered a problem. I went out to start my car, steering wheel is locked, key in ignition won't unlock, can't turn steering wheel to unlock.
View 2 RepliesMy wife owns a 2004 hyundai santa fe, and recently i replaced the belt and idle pulley, I've worked on a few cars in my life and understand the basics and some on how to work on a car.But this has me baffled, the other day i decided to take her car to work. She warned me it had a a slow turn over sometimes i told her okay and headed off to work, drove fine to work no start up issue, but then i went to lunch and it had a slow start like she said. Then in the afternoon started just fine for the drive home to work. I stopped at a gas station to put a little fuel in and the car wouldn't start, it would just release a small cloud of smoke from where the the starter was, so i said ah loose starter wire. That however isn't the case, pulled the plastic shield from the bottom off abd the heat shield off the starter just to find nothing was wrong with either instead its the wire above that running from the wiring harness to the motor, how to fix this issue? Ive attached a few photos
View 1 RepliesThe key in my 2003 Hyundai Santa Fe is rotating freely without starting the car. The Accessories are always on and I had to disconnect the battery to prevent drainage. I removed the lock cylinder and found a small camshaft like part that seems to be loose and broken, one piece of it seems to be broken in the switch. Is there anywhere I can get this camshaft like part? I searched but can only find either the lock cylinder or the switch. See the attached pic for the part I am talking about.
View 3 RepliesI Have a ticking noise coming from the front when I first start up the vehicle and only lasts for 5-10 secs maybe 15 secs tops.. I assume I think its from the engine..
View 15 RepliesWe bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.
Bought my Santa Fe GLS less than 2 months ago and ran fine. Last week, went to store no problems and then went out 5 minutes later, put it in reverse and it stalled. I go to the store, and it lacks MAJOR power.
Now, if I leave it alone for a while it will normally start right up. While idling, everything seems fine. Then my "ghost" takes over the vehicle making it less responsive to the gas pedal. Also, at 3000 rpm, it sounds like its skipping a cylinder. When reading the gauge, it skips between 3000rpm to abut 2800 rpm.
Several weeks ago I made another thread because I was having crankshaft position sensor problems and essentially that was due to a short on the sensors wires which had become exposed. I replaced the sensor and it still did not work until later trying another brand which solved the problem.
I also changed all six spark plugs, wires, and plenum gasket with OEM parts. I was able to get to the back three plugs by following this tutorial with the guidance of a friend who is a mechanic. After getting this done, the car has run way better and smoother.
However, today it has been raining heavily and I needed to run an errand so I went to my car and turned the key but nothing happened. All the dash lights turned on and appeared normal. My radio works, lights work, etc; but I can not get the car to crank at all. I hear the fuel pump turn on and everything else sounds normal, but still no crank. There are no sounds from the starter at all, it is silent when I try to get the car to turn over.
I took a look at the car and the coil pack seems dry, the plug wires are secure, plus we had put di-electric grease on all those connections. The negative terminal on the battery has a solid connection. I even tried jumping the car to see if maybe it was due to the battery, but again nothing happened.
This has only happened once before when it was raining, before I had changed the plugs and wires, but I was able to get it to crank over after about 4 minutes of waiting and contemplating getting a tow. I took a look at all the fuses and they appear to be intact.
I hear a knock once in a while when starting my 2004 2.7 V6 Santa Fe and sometimes when shifting gears. I also hear it when going over rough rough, bumps, tracks etc... I'm thinking motor mounts 152k on the car.
My question would be how many mounts are there, exactly? I've seen three, but maybe another two for the transmission.
The front mount has some separation, but can't tell the others, as I haven't gone under the car with a flashlight just yet.
The majority of the knock seems to come from the driver's side. not sure if that narrows it down at all.