I want to change the glow-plugs on my 2004 Santa Fe CRDI to see if it cures its rough/smokey start up, but I am not sure of their location. I think they might be under the intercooler, but I don't want to strip it all down to find out they are not there.
View 8 RepliesMy 2006 santa fe diesel 2.2 has started to be be a bit smokey when accelerating not even hard had the egr valve off today and gave it a good clean still the same it's not really bad but can see when moving off from parked...
View 2 RepliesI'm new to owning a diesel. I have a. 2004 f250 6.0. I gotta smog the truck this weekend but the check engine light is on. Fault is P0674. I've notice during the day it starts up fine but at nights, lately it's been low 40 outside it won't start. Where to start at.
View 3 Replies#2 contribution/glow plug/injector code ????? Harness looks good. What's the malfunction?? Runs rough. Never seen those 3 codes together.
View 2 Replies2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 RepliesCould a leaking passenger side glow plug harness cause a "hot no start?
View 5 RepliesI have no ground to glow plug solenoid, wiring is ok right up to the computer. Where I should go from there?
Its a 2001 E450 PSD. glow plugs not coming on at all.
should I be checking an engine temp sensor?
I don't have a wiring diagram so I am going in somewhat blind. ]
Where cylinder 1 is located on my 3.5l v6 santa fe. I am replacing the heads and need to know.
View 2 RepliesI somehow managed to kill my 04 Santa Fe 3.5 while doing the dreaded spark plug change and looking for pinpointing and rectifying the problem.
A quick rundown of the car... My mom bought her new in late 03, decided to get a BMW X3 a couple of years ago. I bought her with 65k miles. I just recently had the timing belt replaced by a reputable shop at 79k (yes I know I let it go too long.) I just hit 80k and decided it was also time to do the plugs as I had noticed a decrease in performance and gas mileage of late. Other than the recent dip in performance the car has been extremely reliable and has had no previous issues.
I researched as much as I could knowing that the 3.5 isn't the easiest engine to work on. I bought the recommended Champion plugs that came in the car from the factory as well as the oem Hyundai wires. I also replaced the plenum gasket.
I took my time replacing everything but despite my best efforts, I accidentally cracked the plastic on the radiator reaching over to the back bolts on the plenum. Other than that mishap, the only other issues was the #5 plug sticking which finally came loose after some begging and pleading to the car Gods. Unfortunately, my begging and pleading was enough for them to allow the car to start.
After reading a thread on here, I believe the problem is that I removed the TPS sensor to get to the bolts on the EGR valve, I know now that this was a big mistake. I checked and double checked every connector and can not find one that was missed or disconnected. The car would try to start but would not crank over. I was unable to get any OBD2 codes from my code scanner.
I decided to try a TB from a junkyard and swap it on to see if that was the issue. After swapping it on, the car started and ran like crap for about 15 seconds and stalled out. I was however able to pull some codes in this short time.
The codes I received are:
P0102: Mass Airflow Circuit Low Input.
P110 & P1172: ETS Improper Motor Current.
P1192: ETS Limp home - Target Follow Malfunction.
P2127: Throttle Pedal Position Sensor "E" Circuit. Accelerator Position Sensor 2 Voltage Too Low.
I'm not sure if these codes are left over from before I swapped out the TB or not. I reset the codes after I wrote them down and researched them to see if they reappeared but the car will not start again so I can't get the codes to reappear.
I have a 07 f250 6.0l and it has 112k on it, I've owned it for over 4yrs, since 45k, and no issues, but this morning I went out to start my truck didn't start, tried again and started, but the glow plug controller made a funny buzzing noise, (making that noise for a few weeks), so I went to ford and bought a new controller, so I hope that fixed that, but on my way to work I was at a traffic light and noticed that my ficmv were between 46-48.5, icp 23-24%, vgt around 68%, truck was at temp, should I start to worry about the ficm??, I have to replace my ground on driver side battery, noticed that it is corroding, gonna do that, I have 2 yellow top optima batteries about 3 yrs old....
View 9 RepliesMy 2007 has been having this issue for the last couple of years and has gotten pretty consistent lately. When it's below about 60 and the engine has cooled to ambient temps, it will crank all day and not start. Once ambient temps are about 60, it will fire up and runs like a champ. You'd never know it had an issue. It's got a #4 glow plug fault. Other than that, everything is reading within parameters. FICM, GPCM, or what?
View 5 RepliesI have an 04 F350 with Glow Plug errors on cylinder 2, 4 and 8. I have already replaced the harness on that side because the old one was gunked up pretty bad. Still have the same issue. Does this sound like a GPCM issue to ya'll?
AE pulled the following codes:
P0672 Cylinder 2 Glow Plug Circuit
P0674 Cylinder 4 Glow Plug Circuit
P0678 Cylinder 8 Glow Plug Circuit
Not having issues starting but it rarely gets into the 30's here in FL.
Recently I noticed that three LEDs in my 05 SantaFe's high mount stop light glow even without the brake applied. When the brake pedal is depressed, the entire light glows as it should. But only the three LEDs glow at all times.
View 13 RepliesI just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 RepliesMy coworker is giving me a clean 2001 Santa Fe with 151000 miles. It was running fine then all of the sudden it lost power but was able to stutter home. I went to check it out it started fine but idled a little rough. When I revved the engine it rose to about 2500rpm and stuttered then stalled. Kind of like it was rich and choking out. It then had difficulty restarting.
View 10 RepliesI'm having this cold start issue with my 2001 SF, but it doesn't seem to be fuel related like as the car starts fine but after about literally 1-2seconds the RPMs drop below 1k and the car will stall if I don't put my foot on the accelerator and keep it around 1000-2000 RPMs. But if I happen to make the revs go too high and let them drop again it seems like it wants to stall even easier. After about 30 seconds it smoothens out and drives almost perfectly except for a slight lack of power than normal going uphill (A.T drops to 2nd gear, sometimes 1st depending on the incline). We have had the coolant temp sensor and the fuel pressure sensor replaced. Could it be the MAF? We did clean it one time but it didn't seem to work much at all. Recently out of curiosity, I disconnected the MAF sensor and started the car it being started for a few days. No issue with idling whatsoever!.. ??
View 4 RepliesEvery time i stop for gas..my 01 santa fe is hard to start..it would take 4 to 5 start before she goes, then i have to keep the rpm up, bring her to idle..after that shes ok, till the next fill up.. the only way around this is to keep her running while gassing up..while filling up she run rough idle, some time engine shuts off..then its hard to start..
View 5 RepliesA few days ago, I started my wife's Santa Fe (106k miles) to warm it up and it had a rough idle. I gave it a test drive and the engine light came on and off a few times as it sputtered down the road. I retrieved the codes with my scan tool and it showed - P0300, P0304 and P0306. After some researching, I decided to change the coils, plugs and wires (under upper manifold) this coming weekend.
I have seen the web page instructions for doing this on a 2.7L [URL] .... but it has less stuff around the manifold compared to our Santa Fe. These instructions doesn't include coils was well since the plugs in front use just wires.
My question is.. Is there a set of instructions for the 3.5L for removing the manifold?.. From a less intense standpoint, maybe some of the hoses and cables can stay intact just to move the upper manifold or lift it to the side?... Also, Cyl 2, 4, 6 are the three sparks plugs in the front? 2004 Santa Fe 3.5l ....
I have a 2004 Santa Fe 3.5L 4WD. It's been running rough on occasion for quite a while now, but it's only been an occasional thing. I replaced the front passenger side axle and went for a test drive and the vehicle was barely running. I put the throttle to the floor and it does nothing more than idle. I barely made it home and am afraid to pull it out of the drive. I started it up this morning and it seemed to be idling just fine. I pushed the brake to put it in gear and it started stumbling. When I put it in gear, same thing, pedal not doing hardly anything.
The check engine light did come on and I had a buddy bring down a scanner to check it. I don't know if these are Hyundai specific codes or not, but here's what he pulled: P1110, P2127, P1173, and P1192. I'm thinking throttle position sensor, but am unsure. I've put a lot of time and money into this vehicle lately. I've spent some money and a lot of time trying to figure out why it was showing abs and traction control lights. Turned out to be the exciter ring on the axle was broke.
I have a 2004 SF/2.4 I4. When the car warms up, the ignition coil sparks between the rubber boot and the coil itself, drawing the spark from the plug and resulting in a misfire. This is especially apparent when the A/C is running and the car is idle-ing, resulting in the A/C turning off and a rough jumping idle. Once the car is running this is not noticeable and the A/C turns on.
I have changed the spark plugs to new autolite plugs, and the situation disappeared for a day, but now it is back. I ordered OEM NGK Laser Iridium plugs, I hope they will fix the situation. Why would the A/C matter? Next on the list will be the ignition coil and wire change, but I hope to avoid that.
I recently replaced timing belt and balance belt on my 2004 santa fe 2.4l and now the engine runs like crap and shakes badly. I went over all timing marks again and again and I am at a loss.
View 9 Replies