Santa FE SM (2001-06) :: 2004 - Jerking In All Gears Like Missing
Apr 27, 2012
My 2004 4 cyl Santa Fe the check engine light came on now it jerks in all gears kinda like its missing.
View 1 Replies
Apr 27, 2012
Advertisement
Santa FE SM (2001-06) :: 2004 - Slight Missing At Idle That Occurs All The Time
I will occasionally get a misfire after a rain storm, lasts about ten minutes then goes away. there is also a slight miss (no CEL) at idle, that occurs all the time. I'm thinking spark plug wires.... the plugs were done last year, but nothing else. to my knowledge the wires and coil packs are all original. i'm at about 114K on a 2004 santa fe 3.5l.
Also, does the computer store misfire codes? I know I got them in the past and i checked it at the time, but didn't write down what cylinder it was. think it'll still be in memory?
Think it's ok to change just the wires and not the coil packs? kind of on a budget...
Santa FE SM (2001-06) :: Jerking Or Hesitation While Stopped
Santa Fe - 2004 - 2.7 liter automatic fwd.
I am experiencing an occasional jerking or hesitation while sitting stopped at lights and it also has a tendency to do the same as I begin to move from a stop at times. It almost seems like the transmission slipping or something but likely more engine related I think as I am at a stop. I have felt this slightly while at speed as well but not that often, at least not yet. It also seems more noticeable as the weather get warmer as was very noticeable late last summer and did not present itself again until spring.
Also-I have read that some threads re stalling issues(not exactly what I have) that can be related to the crankshaft position sensor and also read somewhere a while ago about an issue re the ecm needing reprogramming but have not found that recently.
Santa FE SM (2001-06) :: Stalling / Jerking Or Cutting Out While Driving
I have a 2005 2.0 litre petrol Santa Fe. I recently had it serviced and after this I started to have problems with it suddenly cutting out or stalling momentarily while driving. This happens randomly, sometimes at slow and other times at high speeds, often when accelerating but a couple of times in cruise. It only lasts a second or two and picks up immediately but can sometimes happen a few times in succession. It never happened before the service. The orange check light with the exhaust icon (Malfunction indicator Light?) comes on sometimes but I haven't noticed it all the time. This problem is getting worse, more frequent. I pushed the car a bit today in 4th gear up to about 3500 rpm and it happened quite badly, a few jerks in quick succession with the light coming on then back to normal for the rest of the trip.
I brought it back to the garage who did the service (not a main dealer, nor my usual mechanic) and they ran full diagnostics on it a couple of times. Nothing showed up, no error codes and nothing logged on the car's computer. They tested the emissions and found them to be perfect. They didn't change the fuel filter because it seems to be built into the petrol pump but did put something in the system that is supposed to clear out any deposits or whatever. Not sure what it's called but some sort of fuel additive. That was why I drove it hard today. They suggested doing that to try and clear out the system. Doesn't seem to have worked.
The bottom line is they don't know what's causing this so I'll have to take it to my own mechanic or else the main dealer. I'm wondering what could be the problem. From searching the forum it looks like the symptoms could be consistent with a failing CPS, an oxygen or throttle position sensor or a faulty ignition relay. I also think it could be to do with a clogged fuel filter, dirty petrol or perhaps water in the fuel tank; we've had tons of rain lately and the car is kept outside! Given it started happening after the service I wonder if they could have fitted something wrongly, used a faulty part, maybe a plug, or left something loose/disconnected. They have however gone through it thoroughly to try and find the fault so I imagine they would have turned up something like that.
Santa FE SM (2001-06) :: Jerking / Stalling - Need To Jump Start
Bought a 2006 2.4L Sante Fe a few months ago. Had a couple incidents of it jerking after descending the same hill in our neighbourhood. Have a 6 month warranty so brought it to mechanic. All their "scans" were showing everything working so they guessed at replacing the fuel pump and filter. A week later did the same thing but this time it stalled out and I had to jump start to get it back to garage. My wife scanned the internet and noticed other similar complaints. The crankshaft position sensor seemed to come up as being replaced in these incidences, and apparently the "scan" will not show it as failed if it is still somewhat operable. Based on that, we told the garage to replace it as they literally could not figure out what was wrong with the car, having driven it over several days for it to repeat the jerking and stalling we had experienced. It has only been a few days so here's hoping that was the answer.......
View 1 RepliesSanta FE SM (2001-06) :: Brake And Battery Light On - Intermittent Car Jerking
2002 santa fe gls v6. I recently brought the car used and it appears to be in great shape with 135,000 miles, however the car has issues which I'm hoping are minor. Here are my questions:
The brake light and battery light stay illuminated, can this be a bad alternator? Speaking of alternator there is a rattling sound coming form the alternator area, do the bearings go bad? If it is the alternator, does it matter if I use a 95 or 110 amp? Is the alternator difficult to replace?
There is intermittent jerking when in drive. Is it possible that a malfunctioning alternator not delivering proper voltage can cause this type of issue possibly affecting the system computer? Could the jerking be due to something else like crank position sensor?
Santa FE SM (2001-06) :: 2005 - Slipping / Jerking At About 2500 RPMs In 2nd And 3rd Gear
I have a 2005 Santa Fe that for the last week or so has been slipping/jerking at about 2500rpms (2nd and 3rd gear). This only happens after the car has been warmed up and running for 20 minutes or so. I have put it into manual and it does not do this, only when in auto.
View 2 RepliesSanta FE SM (2001-06) :: Delay Shifting Between Gears
Wife's Santa Fe has an issue with it's shift points. Its a 2002 with 148K on it, never has had a CEL, fluid is changed every 60K. Over the past few months the time it takes to shift through the gears is getting longer. What I am describing is not an actual delay between the gears, but rather how long it is starting to take to get the tranny to even shift. Sort of like how a vehicle shifts through its gears when your at a stop, and put the pedal to the floor and just hold it. it makes no difference if your barely on the gas or half way down, still takes a way longer time that it should to shift. It is slightly worse when cold, but still does it when warm. Is there some kind of temp sensor or vacuum line or whatnot that would cause something like this? When it does finally shift, its normal, tight, no slippage or delay. truck runs great other than this.
View 7 RepliesSanta FE SM (2001-06) :: 2003 - TPS Won't Change Gears
I made a mistake, detached TPS from throttle, thought it was purge valve, then I put it back and today my car won't change gears, I messed something up, never had problems with my transmission. Santa fe 2003 3.5 ....
View 2 RepliesSanta FE SM (2001-06) :: Power Loss - Vibration / Missing When Idle
My father owns a 2003 Santa Fe GLS with the 2WD 2.7L V6 engine.
Recently it has been having lots of power loss issues. It vibrates/misses when idling, if you put your foot down on the gas pedal, whether under load or not, it sometimes stalls or just sits there. We took it to Hyundai, and they had no error codes. They charged us $150 to tell us nothing is wrong with it, when clearly something is. The car has become downright dangerous to drive because it cannot make it up hills without stalling/losing power.
The most recent thing we had done to it was the wires/spark plugs changed, which I think was at 65k on the odometer?
Santa FE SM (2001-06) :: Sitting At Stop Light Engine Missing
I noticed this past weekend that when I stopped at a stop light for a long period of time, the engine would misfire for a split second, random, just miss for a moment, then do the same after 15 or so, sometimes less. Other times, no issue.
View 1 RepliesSanta FE SM (2001-06) :: Click While Driving - Missing And No Power Until Warmed Up
My problem is my 2001 Santa Fe petrol 2.7 L its done over 300,000 km one day it sounded like a click when driving, then when I started it cold in the morning it was missing [not running right] and had no power until it warmed up the spark leads are not that old anyway I put new spark plugs in it it seem to run a lot better but seems to be down on power on hills I think coils are ok? the motor not smokey but burn little bit of oil.
View 10 RepliesSanta FE SM (2001-06) :: Transmission Hose Blown - No Gears
The wife was out in the Fe yesterday(2001 2.7 V6 Auto AWD) running at highway speed 80kmh before pulling up to a junction, when she pulled off again then the car came to a halt and lost all drive with engine still running ok. Luckily wife has the sense to switch it off. Tow trucked it home after she saw a puddle of tranny fluid under the car.
Any way it turned out one of the transmission hoses running from the cooler (right hand side hose that runs under radiator) managed to blow off the metal pipe.. don't know how, oem clamp was on and hose didn't split just came off! Needless to say this resulted in the tranny fluid quickly being emptied all over the engine bay and no gears.
So ive re attached the hose with new clamp and have drained what fluid was left in the pan..about 1 liter, and need to fill it up now and find out if it still works ok.
Now the manual says it needs 8.9ltr for a full fill but the question is will it of emptied the torque convertor as well so its completely empty or will it just of blown out the contents of the pan before stopping then just needing half fill.
What could cause a hose to blow off, they don't run at that high pressure normally, average hose pressure is normally 35-55psi from what I can find out so shouldn't blow off that easy should it.
Santa FE SM (2001-06) :: Grinding Noise In All Gears At 3500 RPMs
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 RepliesSanta FE SM (2001-06) :: Hard To Shift Gears (Manual Transmission)
I have a 2004 manual transmission Santa Fe. I've maintained it very well since new.
About 6 months ago I noticed it was getting difficult to manually shift gears. It wasn't grinding or anything, just "hard" to get it to go into the various gears while driving. Before, I could shift into any gear with just 2 fingers on the gearshift and it was smooth as silk.
I went in and had the gear oil changed. This was something I didn't even know needed to be changed and the guy said most people never do. They showed me the oil they took out and it looked more like black water than oil and smelled kinda funky. They changed the gear oil out, but still no difference, and in fact it's getting worse.
The best way to describe it is the only way I can really shift gears now is to find that "sweet spot speed" where the gears will change on their own (so to speak). I find it particularly difficult going from 1st to 2nd, such as when starting from a stop light. People almost rear-end me now as it takes me longer to get it into 2nd gear.
Once in gear it runs perfectly, no problems. The clutch seems to be working normally, except perhaps while stopped in 1st gear, it sometime seems to jerk a bit, and I find this most noticeable if I'm stuck in very slow moving heavy traffic with the constant stopping and then moving forward slightly and such.
It is almost impossible to "gear down" into a lower gear unless I'm at the speed where it would normally go into that lower gear on it's own. The best way to describe it is how it is possible to drive a standard transmission car WITHOUT a clutch if you shift at just the right time/speed. But I DO use my clutch, but if I'm not close to "that speed" it's really, really difficult to force it into another gear, and the few times I do try and force it, I'll often get a bit of grinding.
Santa FE SM (2001-06) :: Transmission Vibrates / Shakes When Shifting Gears
A few weeks ago, my transmission (automatic) started rumbling while shifting from 3rd to 4th and 4th to 5th gear. Shakes the whole car, like you're driving over a rumble strip. Only when the engine is hot. I read online that I should get my transmission flushed and replace the fluid, but should I be expecting the thing to go or is this a normal hiccup for the Santa Fe?
View 5 RepliesGolf IV R32 :: Shifting Gears - Jerking / Clunking When AC Is On
When shifting gears, mainly in 1st, 2nd, and 3rd while the air conditioner is on I'm experiencing jerking / clunking. When I shift it's not a smooth movement and produces a thump. The only way to really avoid this is by letting the clutch out very very slowly. It only happens when the A/C is turned on. Shifting is perfect when the A/C is off.
View 6 RepliesSanta FE SM (2001-06) :: Knock On Driver Side When Starting Or Shifting Gears
I hear a knock once in a while when starting my 2004 2.7 V6 Santa Fe and sometimes when shifting gears. I also hear it when going over rough rough, bumps, tracks etc... I'm thinking motor mounts 152k on the car.
My question would be how many mounts are there, exactly? I've seen three, but maybe another two for the transmission.
The front mount has some separation, but can't tell the others, as I haven't gone under the car with a flashlight just yet.
The majority of the knock seems to come from the driver's side. not sure if that narrows it down at all.
Santa FE SM (2001-06) :: Transmission Go Into Reverse Just Fine But Would Not Move In Any Forward Gears
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesMonte Carlo :: 1997 - Engine Is Stopping Not Just Missing But Jerking
This miss feels like the engine is stopping not just missing but jerking the car for one cylinder. If I just barely hold speed it is minimized or if I step on it it will stop so I'm pretty sure it's not ignition wires or coils etc.. I would suspect pre-ignition but it's been going on a long time ( a year at least) while I've been half fast trying to figure it out so if it's pre-ignition then this is a hell of a strong engine. I have suspected a slightly sticky injector because of the working fine at more throttle. 1997 3.4DOHC Monte Carlo
View 3 RepliesPassat (B7) :: 2015 - Jerking Randomly When Shifting In Low Gears
My car is less than 2 months old and randomly in low gears the car will jerk or lurch when shifting gears. Is this common or does this need to be looked at?
View 18 Replies