Santa FE SM (2001-06) :: 2004 / 3.5L - Cylinder 1 Location
Sep 7, 2014
Where cylinder 1 is located on my 3.5l v6 santa fe. I am replacing the heads and need to know.
View 2 Replies
Sep 7, 2014
Advertisement
Santa FE SM (2001-06) :: 2004 - Rough And Smokey Start Up / CRDI Glow-Plug Location
I want to change the glow-plugs on my 2004 Santa Fe CRDI to see if it cures its rough/smokey start up, but I am not sure of their location. I think they might be under the intercooler, but I don't want to strip it all down to find out they are not there.
View 8 RepliesSanta FE SM (2001-06) :: Location Of PCV Valve?
I have a 2004 Santa Fe with 2.4L 4 Cylinder engine. I have the inexpensive Duralast CV1139DL PCV valve but cannot figure out where to install it.
View 1 RepliesSanta FE SM (2001-06) :: Speed Sensor Location?
My santa fe is throwing a vss code. I was trying to replace it but was not sure exactly where it was. Is it the one right under the air filter box or is that a crankshaft position sensor or some other one?
View 12 RepliesSanta FE SM (2001-06) :: Coolant Temperature Sensor Location
My 2001 Hyundai Santa Fe V6 is giving out a P0118 code, and the "freeze-frame" data reports a -40F for the coolant temperature. That doesn't make sense so perhaps the sensor is faulty or perhaps the sensor connector is loose?
I'd like to take a look at the coolant temperature sensor but I cannot find it. I have scoured hmaservice, hyunda-forums but all the various pics are still not clear enough for me to actually find the sensor. I have seen all the online pics from Hyundai but I can't get my head around exactly where the sensor is - the pics are either too zoomed in or so many things have been disconnected for the purposes of taking the picture I can't get my bearings.
Santa FE SM (2001-06) :: Misfire In Cylinder 3 And 6
I am trying to fix my friend's 03 Santa Fe 2.7L with 325K miles on it. Pulled the codes and he has misfire in #3, 6 and a random one. It doesn't do it all the time, and when it does do it he can sometimes shut it off and restart it and it will be fine.
What is the likely culprit causing the misfires and how to test it? He can't just throw parts at it.
Santa FE SM (2001-06) :: Code P0715 - Input Speed Sensor Location?
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 RepliesSanta FE SM (2001-06) :: Engine Misfire In Cylinder 1 And 4
2002 Hyundai Santa Fe 2wd 2.7L 175,000 miles
Having misfire in #1 &4, new plugs, new wires, new coils, new cam and crank sensors, cleaned and tested fuel injectors, checked injector signal, checked timing belt.
Swapped around plugs, wires and injectors(keeping same firing order) and the # 1 & 4 will not fire. There is spark to the wires and plugs and gas thru injectors but no detonation.
With plenum and exhaust manifold removed (front only) visually checked valves. Installed new oxygen sensors while exhaust was out. Tested ecu fuses in black relay box in engine compartment.
Engine stars first time ,every time but only runs on 4 cylinders. Check engine light code reads no 4 cylinder misfire.
Santa FE SM (2001-06) :: Cranks But No Spark In Cylinder 1 And 4
I have a 2001 Hyundai Sante Fe that died on me while driving down my street. The engine sounded like it was loading up for about 1-2 seconds, then it died. It turns over but does not fire.
After a little troubleshooting, I have no spark in cylinders 1 and 4. I swapped the two coils thinking that I had a bad coil, but then the suspected bad coil created spark on the 2-3 cylinder side. So both coils work.
I towed the car to the shop and the mechanic after about 2 hours of billed labor, he is leaning toward a bad ecu. He said there also is no fuel metering from two of the fuel injectors. He checked the resistance on the injectors and said they are fine. He is thinking it is a control/command issue. The car has many other unrelated problems and I am not sure I want to spend too much more money on it.
I am skeptical about a bad ecu. Or sensors that may be causing my two cylinder no spark and alleged fuel problem?
Santa FE SM (2001-06) :: Code P0302 Misfire In Cylinder 2
I just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 RepliesSanta FE SM (2001-06) :: Faulty Brake Master Cylinder?
I had this sad puppy noise coming from my brakes so I have now replaced my brake booster. When doing so I took my old brake master cylinder and put it on my new brake booster. When trying to bench bleed it it only came fluid from the P marked circuit. It came no fluid from "S". I guess it stands for primary and secondary.
I thought it was because I couldn't press the piston hard enough so I installed it in the car so I could use the brake pedal to get more power. But still no fluid from "S". Is the brake master cylinder faulty? The rear discs are unevenly worn.
Santa FE SM (2001-06) :: Cylinder 3 And 6 Misfire / Shaking When Idle
I just felt that my 2005 Santa fe shakes when idle in front of a traffic light today, later on the check engine light illuminated. Drove to a Monro shop right way and diagnosis using their professional OBD reader, it turns out that the Cylinder 3 and Cylinder 6 are misfiring according to the OBD scan result.
View 9 RepliesSanta FE SM (2001-06) :: Code P0306 Came Up - Cylinder 6 Misfire
I have a 2004 Santa Fe with the 3.5. Today I started it and the check engine light came on. It was not on before this. (We had a lot of wind and rain from the storm but nothing major.) And seems to be running fine. I went to the auto parts store and they ran a diagnostic and the Code P0306 came up #6 cylinder misfire. They said probably Spark plug, wire or coil for #6, then went to look up code in computer and did not have my truck so they went with Kia or Domestic, which gave different possibilities for a code P0306.
They had me buy some fuel injector cleaner as injector was on the list. The light is still on so I guess the cleaner was not the magic bullet. I spoke to a lady at another auto parts store who is a wiz when it comes to cars and has been around them and fixing them a really long time. She says the Code P0306 is Spark Plug, wire, coil #6. She has a 4cyl Hyundai car not truck and she had the code for her #4 misfire in the past and she started her repair cheapest first, Plugs, wires her code was still there she then changed the coil and that did the trick for her.
I on the other hand can't do this stuff myself. Can't afford the dealer anymore or to have a shop do a tune up AND coil if I don't need all new plugs and wires just a coil as they will charge a lot to do a lot all. And it may not need it or even be any of those things. I also suspect the dealer and shops will want to still hook up their computers to do an costly diagnostic because the light is on, even though I know the parts store already came up with a code P0306 twice. Spoke to the dealer on the phone and he already basically said they would want to do that first for $100 plus the cost of repair.
I brought the truck new. It now has 91,500 miles on it and the dealer has already done two tuneups on it in that time, Plugs and wires. I hear it probably shouldn't have even needed these tuneups in this amount of millage? So the last one was probably about 2 years ago and a few thousand miles maybe a guess 10,000-20,000 miles ago. Do you think a plug and wire would be bad already in that few miles?
Santa FE SM (2001-06) :: CEL Came Up With A Code P0303 - Cylinder 3 Misfire
I got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
Santa FE SM (2001-06) :: Key Ignition Cylinder Light No Longer Works
2003 Santa afe 2.7 litre: So for some reason the key ignition cylinder light no longer works, but no issues with the ignition at all. What powers the light, is there a specific part of the cylinder I need to check or replace or do I have to replace the whole cylinder. Would a another cylinder I pick up from the junk yard work?
View 11 RepliesSanta FE SM (2001-06) :: 2002 - Code P0302 / Misfire On Cylinder 2
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.
Santa FE SM (2001-06) :: 2003 - Ignition Lock Cylinder Removal
A few days ago my ignition key would not budge when I tried to start my 2003 Santa Fe. I tried all the tricks like turning the wheel. dry lube, etc but no luck. All indications are that I need a new ignition lock cylinder but I can't figure out how to remove it. I removed all of the plastic and metal shrouding below the dash but can't seem to find a hole to release the cylinder. I have also tried to remove the whole cylinder body assembly by disconnecting the wires and loosening the bolt that secures the "arm" from the ignition cylinder body to the steering column but that also seems to be secured in a way I can't figure out.
View 3 RepliesSanta FE SM (2001-06) :: Burned Out Plug Wire - Number 4 Cylinder Misfire
I've had the plug wire for my #4 cylinder burn out twice in the last 6 months. The car started running like crap and threw a CEL, the code was for a number #4 cylinder misfire. When I pulled the wire it has obvious signs of being burned out, like white powder and burn spots near the base of the wire where it goes over the plug. The plug and coil both look normal. No issues with the other cylinders. What could cause it?
This is on my '05 Santa Fe, 2.7l, FWD auto, with 180k miles
Santa FE SM (2001-06) :: Engine Light Come On With Code P0302 Cylinder 2 Misfire
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 RepliesSanta FE SM (2001-06) :: Leaking Antifreeze - Hole On Cylinder 5 Side Of The Block
We now have a new problem. Motor is leaking antifreeze out of what i will call a weeping hole in the on the #5 cylinder side of the block. The hole, which is manufactured in the block. Is where the antifreeze is seeping from. The hole is located above the bottom bolt an just below the top bolt for the transmission. the hole is on the block. I think that there might be a freeze out plug on the back of the motor block where the leak is coming from. The block was not leaking before we removed the heads for valve job.
View 3 RepliesSanta FE SM (2001-06) :: After Driving It Won't Shut Off - Replace The Ignition Cylinder Or Switch?
I've been having a "turn off" problem with my 03 santa fe. After driving it doesn't want to shut off. The switch will be in the off position and it just keeps running. When I put it in Reverse or drive and then turn the switch off it stops. But which should I look at first? The ignition cylinder/key replacement or maybe something in the ignition switch/electrical? The cylinder assembly is over a hundred $$ and the switch is only $25.
View 3 Replies