I recently replaced timing belt and balance belt on my 2004 santa fe 2.4l and now the engine runs like crap and shakes badly. I went over all timing marks again and again and I am at a loss.
View 9 Replies2007 Santa Fe GLS 2.7 V6. T belt replaced by dealer at 62K. Noticed engine vibration when picked up vehicle. RPM is steady, engine runs smooth, no error codes, no strange noises. Mechanic who did the work confirmed vibration problem and recommended bringing it back - had no answer on the cause but mentioned lose motor mounts which I doubt - the car ran perfect until the dealer did the work.
View 3 RepliesI have 130K miles on my Santa Fe. I just replaced the timing belt without the water pump being replaced. Picked it up from the mechanic and the check engine light was on and it was idling very rough. Left it there for him to recheck. He said maybe he didn't plug in the Cam Sensor all the way or at all. Next day he called me and said that the cam sensor was bad and he replaced it for free. Picked up the vehicle and the idle was a little rough but got worse on the ride home.
View 1 RepliesI have a 2009 Sante Fe with 60,258 miles. I had the timing belt changed at 60,000 miles at the dealer. I now have a check engine light that shows the following two codes.
P0321
P0612
These codes are related to a timing belt change? Could a sensor have been removed for the work and not replaced correctly?
My 2003 Sante Fe has developed a rattling sound in the engine. The oil level has been good. I took it to a dealer for diagnoses and they told me that the engine was gunked up and the timing "chain" tensioner couldn't move to keep it tight and it was rattling. They put some engine cleaner in and changed the oil and wanted me back in 500 to clean it again. I did that again, but the rattle is still there. It gets a little quieter after I have driven it for a while.
My question is doesn't the Sante Fe have a timing belt? If that is the case what do you think the rattle is?
Son has a 2004 Hyundai Santa Fe 2.7 motor. The timing belt broke before we could replace it. Long story short, 24 valves, gaskets, timing belt, water pump, new belt tensioner and new pulleys. The motor is back together. The only problem is when you turn the ignition switch on, it blows the CPU fuse. The only electrical part we replaced was the purge valve.
View 3 RepliesMy 2001Honda Civic EX (manual) has only about 46,000 miles on the clock and runs very well. My mechanic says I should consider replacing the timing belt (the manual suggests after seven years). I plan on keeping the car for many more years -- should I replace the belt now? How devastating is it if the belt breaks while driving?
View 5 RepliesI got 123000 km on my car. Manual says 144000 km is the right mileage to replace the belt, but I have heard opinions that it should be done earlier.
View 7 RepliesI just had the timing belt (water pump and thermostat) replaced in my 2004 V8. I drove it home from the dealer (75 miles or so) without incident. Drove it to and from work (4 miles) without incident for a few days.
Last night I drove ~5 miles, idled in a parking lot for ~10 min and then drove another 5 miles and it overheated. Once I shut off the car it would not come back on. I waited for it to drop below 200C and it still didn't start. Electric consumers would come on all was well....but no start.
Car was towed to the local VW dealer who do not have a phaeton tech. After the hour and half it took for the tow truck to arrive and half an hour to tow it....it started up.
I am now thinking about my next move. As I read through everyone's overheating experiences they are mostly
1. Failed thermostat (which one? does the bottom thermostat control water pump operation?)
2. Fan issues
3. Air in the coolant line following a flush (could be, but I drove it home in the cold on the first day with the heater on)
4. False readings due to a bum (upper?) thermostat.
I have a VCDS but have not been able to get out to the car to give it a shot.
I just installed a new timing belt, balance belt, idler, and both tensioner pulleys but am getting a little whine. I adjusted the balance belt but the noise does not change. No other belts or items are hooked up yet this was a dry run. Car seems to run fine and idles well. The hydraulic unit seems to be working fine and it's a OEM Hyundai piece.
Anything common I can look for that should stand out? 2002 Santa Fe 2.4L
We have an 04 v8 phaeton. Hubby just changed timing belt with the blauparts top kit. He rented their tools. When he went to attach the bar it didnt line up. He finally got it all back together and it runs fine. The vag com scares me, though.
Those codes say...
- 16405 bank 2 camshaft a (intake) p0021-002 retard setpoint not reached (over advanced) mil
on and the other
- 16395 Bank 1 p0011-002 retard setpoint not reached over advanced mil on.
He just ran the scan today and we are leaving on a 1500 mile trip tomorrow. He says he knows it lined up right...im doubting it. We have driven it about 500 miles since he changed it...no problem. I don't want to risk damaging something. Would you take it on a trip with that code?
I have a problem with my 01 santa fe. When I start it the engine runs rough and when u try to give it gas it pops or backfire through throttle body and air intake tube? Checked the timing belt its ok hasnt slipped.so im stuck at this point.
View 8 RepliesWhen firing up the engine cold it runs really rough, smells very rich all the time, even warmed up. No codes set, fuel trims are within 5-10%. I've replaced the front O2 sensor, swapped crank & cam sensors, Map sensor (have lots of spare parts) & I'm sure there was more things I've changed but can't remember. I have a snap on scanner and everything is within parameters.
I have not checked the EGR valve or solenoids yet. It's a 2006 Santa Fe 2.4l 5 speed, new timing belt & balance belt replaced when I dropped this engine in. Is there a common problem with these that I could begin looking for?
I have a 2006 Honda Odyssey. I got the timing belt replaced two weeks ago.Last week the engine started making a quiet clicking noise upon acceleration. The clicking noise happens intermittently not continuously. Then last night the yellow engine light came on. Questions: What does the yellow engine light mean? Is the engine light related to the timing belt work that was done? Would the clicking noise be connected to the timing belt work?
View 3 RepliesRecently replaced plugs/wires on soon-to-be 10 year old '04 SF 3.5L (157K mi.) for the first time.
Plugs were OE Champion Platinum and all 6 looked identical except for excessive gap of .010 +/- due to all the miles. Replaced plugs with same as OE. Old plug wires looked good, but replaced them with aftermarket wires ( fit was as good as OE). Also replaced plenum gasket.
Problem is: engine runs rough at idle and high rpm and appears to be mis-firing. CEL is off and code reader shows no Trouble Codes stored.
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
We recently had the timing belt replaced in our 2003 Volkswagen Passat (1.8T). Now it shakes and vibrates badly when we put it in drive and idle. It ran smoothly before we had the belt replaced. The mechanic hasn't found a solution yet.
View 2 RepliesI changed the timing chain, phasers, tensioners, guides, and cam sensors and solenoids about 30k miles ago. Truck now has 170k miles. This past weekend engine started running so rough, it had the whole front end shaking. Threw 8 codes..1 bank..lean, bank 2 rich, timing retarded, cylinder G and F misfire, and more codes. It seems to have jumped timing pretty bad.
View 1 RepliesI am looking for a link or instructions on replacing the timing belt on a 2.8 30V. I attempted to search and mostly came up w/ the info relating to the turbo.
View 2 RepliesMy 2004 Passat 1.8T GLS (station wagon) has 72,000 miles. I checked the manual which says that timing belt is to be replaced at 105,000 miles.
However, car is 8 years old - does the age matter or I should be fine until I get to 105,000 miles to replace the timing belt, tensioner, water pump etc.
Does VW have an official recommendation for replacing the timing belt?
None of the publications I've seen list the timing belt interval. My car is very close to 95k miles.