Santa FE SM (2001-06) :: 2003 Won't Start In Gear
Sep 4, 2014
Two times in the last month my 2003 Sante Fe would not start - the radio, air conditioning will come on but nothing from the engine - not even a click - no check engine light. Had it towed both times - as soon as it was towed it would start up. It seems to happen in 2 week intervals. Now I realize bc they had it in neutral to get on the truck that is what required to start. It hasn't happened in a week but I know it will again.
View 3 Replies
Advertisement
We have a Hyundai Santa Fe 2003 2.7 V6 and sometimes it just won't start, the starter motor turns over fine and the battery is fully charged, and most other times it starts straight away. The engine purrs nicely when it's running.
I suspect it's an electrical fault, perhaps a faulty sensor? (Cam position sensor, crank position sensor, fuel position sensor?) What sensor would cause the car to start and run perfectly some times and not start at all other times?
Immobilser issue? Although I don't have a button on my key so maybe the car doesn't have one.
View 2 Replies
The past couple weeks, my '03 Santa Fe 2.7 has begun to grind a while before starting -especially when weather is hot and has been sitting a while. Once it starts, all is normal. Most of the time it starts right up -no problem. This just happens once in a while. Slowly, it seems to be getting worse. I replaced battery -no change. ...................???
View 28 Replies
We recently changed the timing belt & serpentine belt & new alternator. Drove great for 2 days. Then car would stall out when idling, had rough idle. We replaced the Crankshaft position sensor (got one from the dealer) & the electrical connector. The engine cranks but won't start. The only code we're getting is P0335. We've checked all the fuses. Fuel pump starts when turning on the key. We've been a week without a car and trying to come up with something.
View 6 Replies
Two times in the last month my 2003 Sante Fe would not start - the radio, air conditioning would come on but nothing from the engine - not even a click - no check engine light. Had it towed both times - as soon as it was towed it would start up. It seems to happen in 2 week intervals. Now I realize bc they had it in neutral to get on the truck that is what facilitates it start. It hasn't happened in a week but I know it will again.
View 1 Replies
I am having serious problems with my 2003 Santa Fe 2WD 2.7. First, about two months ago, I would have typical crankshaft position sensor problems whenever it would rain outside and my car would not start or if it did it would eventually stall while driving. Before stalling, the engine light would come on with code P0335 and the engine would shake. I did my best not to drive it during these moments and was always able to get it back home. The problem went away after a couple days of issues until recently.
About a week ago, the P0335 code came back with associated symptoms; however, this time it would not go away. It is worth noting however that I am in Portland Oregon and it is raining non-stop this time of the year. I am not a mechanic, but my neighbor used to be and he carefully guided me through replacing my Crankshaft Position Sensor, Camshaft Position Sensor, and several spark plugs.
After all of this work, my car turns over and starts for maybe a second, where before it would not even fully turn over in my driveway. It immediately dies after the second and then I can not get it to start up again unless I charge the battery for a bit or hook it up to another car and even then its only that initial second of start up. Additionally, there are no longer any codes or check engine light, but there is a "pending p0335" on my neighbors reader. I thought maybe my crankshaft sensor was defective, so I got a second one and it is still the same deal.
It is also worth noting that I do not see any tachometer movement during start up. When we replaced the Crankshaft sensor the old one was destroyed. The wires on it were either burnt up or the plastic coating had decayed away almost completely; thus the reason it was shorting out.
My car has all new belts done through a dealership as of 10 months ago, so I doubt it is related to the timing belt. My neighbor thinks it may be bad fuel, although I always get good fuel and I also doubt this is the case. During key-on you can hear the fuel pump start up and other components all working normally, so it is unlikely related to that.
View 7 Replies
I have a 2003 2.4L 5 speed manual Santa Fe. I was parking my vehicle and removed my key as usual and realized that the car was still running. I put it into reverse rolled back and back into 1st to roll forward just to make sure I wasn't dreaming. I ended up pulling the fuel pump fuse and disconnecting the battery to turn it off.
When I replaced the fuse and reconnected the battery I was able to bump start the vehicle without the key in the car and drive it all the way home with no problem. I took apart all the plastic pieces around the Ignition and attempted to remove the cylinder but was unable to locate any sort of small button or pin to push on to remove it. Where is the release button?
What are my options here? Do I replace the cylinder first or get a new key, or is there something else that I should check first before I take it in.
View 1 Replies
It seems to have difficulty starting during stop and go like on deliveries. Also has problems after refueling. Is this caused by a faulty purge valve? If so where is it located?
View 5 Replies
This concerns a 2003 Hyundai Santa Fe 2.7L engine.
Bad rain, combined with a puddle splash caused a short (someplace). Vehicle ran poorly on way home and then eventually failed to start. Replaced the Cam Position Sensor and the Crankshaft Position Sensor. Checked all wiring and connections. Cleared codes and the vehicle started. Ran for about 15/20 minutes and a P0340 code popped with the engine light on. Car still runs fine. Researched code and learned that this code is a Camshaft Position Sensor A - Circuit Malfunction.
1. Bad ground in Circuit.
2. Open Circuit that fails to close.
3. PCM malfunction.
Questions:
1. Where in this vehicles is the PCM located? Is it within the main ECU in one of the other ECU fuses or an independent fuse?
2. Other than the 3 issues listed above, could I be overlooking anything else?
View 3 Replies
Its not my car but my sister in laws. She stopped by our house tonight to pick up her kids and when she put the car in drive it showed both drive and 2nd gear. we tried disconnecting the battery so she could at least get it home (3 min away) but it didn't change anything.
She left with it still in 2nd thinking she could make the short drive without any problems but half way home it shifted down to first and it wasn't even driveable. Everything i have read on the web (which was not really specific to the santa fe) was say that its stuck in safe mode. What could have cause the problem? So far no check engine light has come on.
View 2 Replies
ok, I had quite bit of work done, prob over yr ago All oem parts, timing belt, crank sensor, idler pulley, some other things while in that area. So when he was done I got this vibration when it goes into gear never in park only in rev. or drive but only in cold weather and after it warmed up it was go away. No Trans service was done. He kept it overnight outside, had the timing cover off rolled it in the garage, started it and seen that the belt was flapping crazy. So he thought it was that. well every cold morning I have to wait till it is warm to not hear that sound. it only happens during cold mornings never in summer. He had back in his shop 3 times after parts were installed. and its to this day isn't the same. its unfortunate that I didn't have many cold mornings when he had worked on it. but after I had it and the next cold morning it was there.
View 7 Replies
2003 Santa Fe 41,000 stuck in first gear.
View 1 Replies
I have Santa Fe 2002 v6 2.7 and it's have been in the mechanic for 2 months now.
Suddenly my gear box don't go up 3rd, the error that the diagnostic reader is P 1528. What it can be? How to Fix it?
View 2 Replies
2003 Santa Fe, 2.7L V6
When placed into Drive, the transaxle (and indicator lights) behave as though the gear selector was in the manual gate and at 1st gear. It seems that no matter what I do (wiggle the selector, disconnect the battery, etc) will bring it out of 1st gear while in D. This issue first occurred about a month ago and it somehow corrected itself. I had hoped that it was a fluke, but it is happening again. Initially, I suspected that it might be a switch or something within the gear selector lever housing in the console, but I've done a bit of searching the webs and it looks like it may be more of a sensor(s) issue.
View 8 Replies
I've been having ongoing issue with lack of power uphill in my 2005 2.7L Auto and noticed during recent freeway driving that when its in cruise mode the car will shift down through 3rd then into 2nd to maintain cruising speed on a steep-ish slope.
That was with adult driver me and two kids in the car so no extreme load involved.
Does car needs to be in such a low gear at 110kmh/70 mph to cope with a slope?
View 6 Replies
My Santa Fe 2001 model V6 4X4 Automatic shift gears down hard from 3rd in to 2nd. I checked transmission oil and its light brown. Should I drain and refill or not worth it.
View 7 Replies
The shifter will not usually stay in 5th gear for very long. The clutch and flywheel were replaced a few weeks ago just before i purchased the car but this problem has only cropped up in the last week. Could it be shifter linkage adjustment?
View 3 Replies
I have a 2004 3.5L Santa Fe with about 170k miles on it.
Runs great. I am going to change the timing belt here in the next week or so.
I have started having an issue where going into second gear it will jerk, almost like sputter. Does not do it all the time. Seems like a sensor or computer issue because the rest of the gears shift smooth. And if was a problem with the internals of the transmission I would think it would always do it and never go away.
What the issue could be since I am already going to be digging deep into the vehicle might be worth replacing more parts, what it is.
View 7 Replies
I have an 01 and 02 santa f. I took the v6 out of 01-and put in the 02.put new gaskets on engine new timing belt etc. Got engine in and runs like a champ. But the tranny which looks new I assume its been replaced. It starts out in 2 or 3 all the time want shift into od. Reverse works. So I found one plug dangling I couldn't figure out where it went then i found it. It plugged up on top of tranny. Well now it starts out in first and shifts through all the gears. Drove it down the rd shifted fine. Turned around and put in reverse then when i went to drive it jerked real hard. Shifted out fine so I went to floor it to make it kick down and it jerked again. This time it was hung in 3 or drive cause when I pulled into my driveway it was in high gear and u can put it in manual mode and the light only goes to second and d when it acts up like this. So i killed the car started back up and know it will go into first in manual mode and shift out and do fine?
View 3 Replies
I have a 2002 Santa Fe V6 2.7 liter, FWD, 215,000+ miles. When it shifts from 2nd to 3rd the whole vehicle jerks. It does not do this on the other gears. I took it by a transmission place for a free scan and they said the transmission is fine.
View 19 Replies
My brother's 2005 Santa Fe keeps locking up in 3rd gear. I've read around here that the P0715 error code that I have is for an input sensor, but I replaced that and it still doesn't work. I also tried the vehicle speed sensor as well and it didn't work.
I was with someone at AutoZone who pulled up a page here that said no I really needed to replace the transmission control module but I can't find that thread here.
View 2 Replies
