I made a mistake, detached TPS from throttle, thought it was purge valve, then I put it back and today my car won't change gears, I messed something up, never had problems with my transmission. Santa fe 2003 3.5 ....
View 2 RepliesI have a 2003 camry LE and for the last few days I am having issues changing gears. I hit the brakes and the gears wont change from park. I can sometimes get it to work by hitting the brakes harder or pumping the brakes.
View 2 RepliesI have Toyota camry LE 2003 model. Today evening, my car got started but I was unable to change the gears. Apart from that, my odometer reading goes off. My heater fan also did not start.
It's very cold here in minneapolis, (-10 F outside). Is this because of that? I started my car from my parking lot to shopping mall which is 0.5 miles apart. while coming back, this happened.
Wife's Santa Fe has an issue with it's shift points. Its a 2002 with 148K on it, never has had a CEL, fluid is changed every 60K. Over the past few months the time it takes to shift through the gears is getting longer. What I am describing is not an actual delay between the gears, but rather how long it is starting to take to get the tranny to even shift. Sort of like how a vehicle shifts through its gears when your at a stop, and put the pedal to the floor and just hold it. it makes no difference if your barely on the gas or half way down, still takes a way longer time that it should to shift. It is slightly worse when cold, but still does it when warm. Is there some kind of temp sensor or vacuum line or whatnot that would cause something like this? When it does finally shift, its normal, tight, no slippage or delay. truck runs great other than this.
View 7 RepliesThe wife was out in the Fe yesterday(2001 2.7 V6 Auto AWD) running at highway speed 80kmh before pulling up to a junction, when she pulled off again then the car came to a halt and lost all drive with engine still running ok. Luckily wife has the sense to switch it off. Tow trucked it home after she saw a puddle of tranny fluid under the car.
Any way it turned out one of the transmission hoses running from the cooler (right hand side hose that runs under radiator) managed to blow off the metal pipe.. don't know how, oem clamp was on and hose didn't split just came off! Needless to say this resulted in the tranny fluid quickly being emptied all over the engine bay and no gears.
So ive re attached the hose with new clamp and have drained what fluid was left in the pan..about 1 liter, and need to fill it up now and find out if it still works ok.
Now the manual says it needs 8.9ltr for a full fill but the question is will it of emptied the torque convertor as well so its completely empty or will it just of blown out the contents of the pan before stopping then just needing half fill.
What could cause a hose to blow off, they don't run at that high pressure normally, average hose pressure is normally 35-55psi from what I can find out so shouldn't blow off that easy should it.
My 2004 4 cyl Santa Fe the check engine light came on now it jerks in all gears kinda like its missing.
View 1 RepliesCodes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 RepliesI have a 2004 manual transmission Santa Fe. I've maintained it very well since new.
About 6 months ago I noticed it was getting difficult to manually shift gears. It wasn't grinding or anything, just "hard" to get it to go into the various gears while driving. Before, I could shift into any gear with just 2 fingers on the gearshift and it was smooth as silk.
I went in and had the gear oil changed. This was something I didn't even know needed to be changed and the guy said most people never do. They showed me the oil they took out and it looked more like black water than oil and smelled kinda funky. They changed the gear oil out, but still no difference, and in fact it's getting worse.
The best way to describe it is the only way I can really shift gears now is to find that "sweet spot speed" where the gears will change on their own (so to speak). I find it particularly difficult going from 1st to 2nd, such as when starting from a stop light. People almost rear-end me now as it takes me longer to get it into 2nd gear.
Once in gear it runs perfectly, no problems. The clutch seems to be working normally, except perhaps while stopped in 1st gear, it sometime seems to jerk a bit, and I find this most noticeable if I'm stuck in very slow moving heavy traffic with the constant stopping and then moving forward slightly and such.
It is almost impossible to "gear down" into a lower gear unless I'm at the speed where it would normally go into that lower gear on it's own. The best way to describe it is how it is possible to drive a standard transmission car WITHOUT a clutch if you shift at just the right time/speed. But I DO use my clutch, but if I'm not close to "that speed" it's really, really difficult to force it into another gear, and the few times I do try and force it, I'll often get a bit of grinding.
A few weeks ago, my transmission (automatic) started rumbling while shifting from 3rd to 4th and 4th to 5th gear. Shakes the whole car, like you're driving over a rumble strip. Only when the engine is hot. I read online that I should get my transmission flushed and replace the fluid, but should I be expecting the thing to go or is this a normal hiccup for the Santa Fe?
View 5 RepliesI hear a knock once in a while when starting my 2004 2.7 V6 Santa Fe and sometimes when shifting gears. I also hear it when going over rough rough, bumps, tracks etc... I'm thinking motor mounts 152k on the car.
My question would be how many mounts are there, exactly? I've seen three, but maybe another two for the transmission.
The front mount has some separation, but can't tell the others, as I haven't gone under the car with a flashlight just yet.
The majority of the knock seems to come from the driver's side. not sure if that narrows it down at all.
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesI have a 2003 Santa Fe 2.4L (automatic) with 200,000 miles. Auto shop is recommending I change my transmission fluid. I've heard that changing the transmission fluid on a high-mileage vehicle is potentially dangerous. I haven't noticed any symptoms of "bad" transmission fluid.
View 5 RepliesI changed the purge valve because it was hard to fill up. It idles fine but when I drive it at 40 and just cruise without a load on engine it starts to jerk or misfire. I'm going to change plugs even though they don't look bad and wires.
View 2 Replies2004 Santa Fe, 2.7 L V6. The oil was changed approx 5-7k miles ago (not really sure as I bought it from someone else) and I just changed it today. There's a new knocking noise in the engine. I used normal castrol GTX oil, 5w-30.
I drove it about 20 miles and the noise is still being made, so it's not a circulation problem.
I somehow managed to kill my 04 Santa Fe 3.5 while doing the dreaded spark plug change and looking for pinpointing and rectifying the problem.
A quick rundown of the car... My mom bought her new in late 03, decided to get a BMW X3 a couple of years ago. I bought her with 65k miles. I just recently had the timing belt replaced by a reputable shop at 79k (yes I know I let it go too long.) I just hit 80k and decided it was also time to do the plugs as I had noticed a decrease in performance and gas mileage of late. Other than the recent dip in performance the car has been extremely reliable and has had no previous issues.
I researched as much as I could knowing that the 3.5 isn't the easiest engine to work on. I bought the recommended Champion plugs that came in the car from the factory as well as the oem Hyundai wires. I also replaced the plenum gasket.
I took my time replacing everything but despite my best efforts, I accidentally cracked the plastic on the radiator reaching over to the back bolts on the plenum. Other than that mishap, the only other issues was the #5 plug sticking which finally came loose after some begging and pleading to the car Gods. Unfortunately, my begging and pleading was enough for them to allow the car to start.
After reading a thread on here, I believe the problem is that I removed the TPS sensor to get to the bolts on the EGR valve, I know now that this was a big mistake. I checked and double checked every connector and can not find one that was missed or disconnected. The car would try to start but would not crank over. I was unable to get any OBD2 codes from my code scanner.
I decided to try a TB from a junkyard and swap it on to see if that was the issue. After swapping it on, the car started and ran like crap for about 15 seconds and stalled out. I was however able to pull some codes in this short time.
The codes I received are:
P0102: Mass Airflow Circuit Low Input.
P110 & P1172: ETS Improper Motor Current.
P1192: ETS Limp home - Target Follow Malfunction.
P2127: Throttle Pedal Position Sensor "E" Circuit. Accelerator Position Sensor 2 Voltage Too Low.
I'm not sure if these codes are left over from before I swapped out the TB or not. I reset the codes after I wrote them down and researched them to see if they reappeared but the car will not start again so I can't get the codes to reappear.
What is the interval when trans fluid gets changed? I need to take a trip....round trip will be about 4600 miles I probably have less than 1500 on the current fluid now.. and before that had changed it 2 other times within 1000 about 8 mo. apart just to rotate the fluid. I am planning to do it as soon as i get back.
View 8 RepliesI have a 2001 2.7 v6 automatic it has started to struggle up hill to change gear.... and has no power ... it Rev's over 4000 before it changes out of second but fine sometimes after that .. i have had a terra clean done and no fault show on any diagnostic thing.
View 3 RepliesIts been getting quite cold here lately at night and in the morning when i go to the santa fe it makes a ticking noise for about 2-3 seconds and everything is fine again. I was thinking of dropping a quart of transmission fluid in the crankcase run it for a bit and change the oil?
View 14 RepliesI've got a 95 Intrepid that wont seem to change gears when I have the accelerator all the way down (from standing and passing gear). Other than that it seems ok. I want to add some Lucas. I am worried about overfilling...Lucas says a moderate overfill is ok, but I am still apprehensive.
View 2 Replies,I have a 2004 C70 Volvo. One day I noticed a sizable puddle of oil underneath the car that came out of the transmission box. The car turns on fine, but when I put it in drive and press on the gas pedal, I hear the engine roar but the car doesn't move an inch. It is as if the gears were on neutral. I tried reverse and the same happens; I just hear the engine roar with no movement at all.
I asked one mechanic and they said I need a new transmission- which is very expensive- but they didn't give me an explanation. They just said 'it happens'... What is wrong specifically (just out of curiosity)? As far as I know this was a sudden problem. The car was working fine the previous day then the next day, I see the puddle of oil and the transmission doesn't feed at all.Is my only option is buying a used transmission (costs around a couple of grands)?
i wanna put a lift kit on my 87 pathfinder but i was wondering if i would have to change the gears, if so how would i change them?
View 3 Replies