Santa FE SM (2001-06) :: 2003 - Odd Noise From Brake Pedal In Stop And Go Traffic
Jun 27, 2013
I've been noticing an odd noise in the brake pedal in our '03 Santa Fe. I don't hear it all the time (almost never on the highway), but especially hear it in stop-and-go traffic. It's sort of a whirr, a "RRrrr". I've googled and watched YT videos and it's definitely not a hissing sound or a grinding sound, nor do I notice any difference in the brakes' responsiveness.
I'm apprehensive of taking it to the dealer for service because I only plan to have this vehicle for at most three more weeks. Have only held onto it this long because we couldn't afford to replace it until we sold our house-- which we've just done, and are about to move to a city about an hour away on 7/5. We'll trade in the car within a couple of weeks of moving.
The noise is definitely from the pedal and isn't anything like squeaking brake pads (I currently live in the DC metro area, so squeaky brakes become very familiar with all the stop-start traffic!). The videos I've found that point to a booster problem have a decided hiss, and it's not that either. Don't want to be unsafe in the time we've got left, but also don't want to throw another thousand bucks (every time something breaks in that darn thing, it always seems like it's about $800) into a car we won't have in a month's time.
View 6 Replies
Advertisement
This weekend was a nice high 80's low 90's. My AC is usually ice cold. However now that the weather hit that high, when we are in stop-and-go traffic, the AC starts blowing warm humid air. I do see the temperature need creep a bit higher than the normal range.
Once we start driving, after a few minutes, the climbs back down and the cold AC returns. Turning the fan speed down, or turning the compressor off, then on again, seems to work.
What could be causing this? A friend said he has this issue with his car claiming the engine is the issue, not being powerful enough to keep the compressor running right, is that possible?
View 14 Replies
Just got a 03 Used Santa Fe 2 weeks ago... 79,000 miles
1. Car "lurches" when at a complete stop w brake fully applied out of no where, so strong that I could easily rear end someone...
2. told dealership car was pulling to right, they said (after some teeth pulling) that a ball joint was replaced and Santa Fe's don't need alignments but in MA this is part of state inspection and considered a safety issue, needless to say, they say I have to pay for it...
3. Rear brakes seem to be hanging up...
All I want is the issues fix.
View 2 Replies
Was in town stopped at a traffic light when my 2003 Santa Fe just shut off. No warning, started right back up again, no CEL, no DTCs. Scary. I'm happy it happened with me driving the car instead of my daughter driving. Also happy it didn't happen on the highway.
I've had hard starting issues for a while now. Replaced crank sensor, it's fine for a few starts, then goes back to hard starting, but I hadn't had a problem in a few weeks.
View 8 Replies
I have a 2005 Santa Fe 2.7 V6.
For over a month I have had a soft brake pedal. For those that may not know what that is, I push my brake pedal down 3/4 of the way, and I'll finally feel the brakes catch; however, I cannot stop quickly. I have had to use the Sports Mode to slow down my car many times.
I brought it to my local mechanic and he has done the following:
1) he thought it might have been the master cylinder, so he replaced it. he checked the old master cylinder and found nothing wrong.
2) bled the brake system a couple of times, but it still came back
3) brought my car to the local dealer to drain the ABS system. The problem still came back.
I waited over an hour as the dealership's service department checked out the car. Someone finally came to me and said they checked the lines and they are not leaking, so it has to be the master cylinder. I told the guy that it's a brand new cylinder, and when the mechanic looked at the old one, he said there was nothing wrong with it. All he could say was it's not the lines, it's the cylinder. If I had the problem before & after the master cylinder was replaced, & nothing was wrong with the original master cylinder, how is it the master cylinder?
I called my local mechanic on my way home from the dealership and told him what happened. He said he was going to do some research, mentioned something about replacing something with the ABS and he would call me today.
I searched the forums for brake issues and saw something about cracked ABS rings. Could that be an issue? Could it be something else?
View 21 Replies
I have an issue that i have been trying to resolve. When i depress the brake lightly to a stop, the pedal pulsates. But if I depress a little harder it pulsates initially midway down and then it stops as i press harder to brake. (I hope this is easy to understand). so... press lightly, pulsates until I reach a stop. press firmly, pulsates briefly, then no pulsation until i reach a stop.
I have pretty much replaced everything. Calipers, rotors, pads, lnes, fluid, hardware. lugs are torqued to 100ftlbs.
Also the caliper is not sticking the problem persists even after I replaced the calipers. I am left at a total loss here. I cant think of anything else. One thing that i noticed is, the LUGS are really hot to the touch after driving it for 15 min or so.
View 8 Replies
Soft Pedal. 2004 Santa Fe, front wheel drive 4cyl, 2.4l
When I first owned this Santa Fe the brake pedal was high and had lots of stopping power, over the last few years I noticed the pedal was getting lower. I have replaced everything needed thus far including pads, rotors and everything has recently been serviced front/rear/emergency brake/ calipers and still a soft pedal. Had the guys in our recon shop replace master cylinder and bleed the lines a few times with a full week in between bleeding to ensure there was no air in the lines. The mechanics are stumped but I'm wondering if we missed something...... I still can stop no problem but there is no grab in brakes until pedal is half way down to the floor or worse.
View 15 Replies
I have a santa fe 2002 diesel the abs lights stop on all the time the brake pedal has a bad judder on it when braking. I have taken the fuses out and it will still judder. The only thing that is when i disconnect each sensor the red brake light stops on but not with the osf front sensor. All the rings look ok but when i had a problem with 1 of them the abs light would go out then return on...
View 1 Replies
Here's the short of it. 3rd time in a year the brakes on my 2005 SF (177K miles, 2.7L) have gone out.
The brake pedal is very soft and goes to the floor before braking occurs. Typical signs of a bad master cylinder.
The first time was a year ago. I bought a re-manufactured master cylinder, change it and bled the brakes. Worked like a champ and lasted 10 months.
To months ago same exact symptoms. I assume it was a bad re-man part. It's under warranty, not big deal. I do warranty exchange, bleed system, brakes return. All is good.
Less then 3 weeks later, brakes gone, same symptoms! This time I spend the difference and get a brand new OEM cylinder with reservoir. Replace, bleed, problem fixed. Brakes go out in less than a week.
I'm not leaking anywhere. Reservoir is to corect level. ABS light is NOT on. No chattering in brakes. Braking is smooth both when power brakes work and when not. No visible damage to calipers. I'm 99% sure there is no air in the system, but I'm going to try bleeding again. I have not put it up on a lift to yet to check all the lines.
View 21 Replies
I have a 2004 Santa Fe 3.5L 4WD. It's been running rough on occasion for quite a while now, but it's only been an occasional thing. I replaced the front passenger side axle and went for a test drive and the vehicle was barely running. I put the throttle to the floor and it does nothing more than idle. I barely made it home and am afraid to pull it out of the drive. I started it up this morning and it seemed to be idling just fine. I pushed the brake to put it in gear and it started stumbling. When I put it in gear, same thing, pedal not doing hardly anything.
The check engine light did come on and I had a buddy bring down a scanner to check it. I don't know if these are Hyundai specific codes or not, but here's what he pulled: P1110, P2127, P1173, and P1192. I'm thinking throttle position sensor, but am unsure. I've put a lot of time and money into this vehicle lately. I've spent some money and a lot of time trying to figure out why it was showing abs and traction control lights. Turned out to be the exciter ring on the axle was broke.
View 1 Replies
When I brake slow to stop or go slow round corner brake pedal judders with a brake judder noise I have read it could be cv axle or the ring tone or sensor cable.
I have replaced front discs and pads because I thought it was that but not then abs light came on and went back off and and one time stayed for awhile.
Santa Fe 05 Diesel 48000 on clock
View 2 Replies
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 Replies
I have a 2010 Santa Fe w/ ~25,000km. Yesterday, I noticed that after depressing the brake pedal (while driving) i hear a wheezing noise and then a click right before i come to a complete stop. When i am stationary, and i depress the break pedal, i hear the clicking noise but no wheezing sound.
I just took it into service today and even drove around the lot with one of the service techs and he says its normal. That the clicking noise is coming from the shifter release. I don't believe i heard this sound when i bought it, nor any other time till yesterday. The sound is driving me crazy! This cant be normal .... can it?
View 5 Replies
Recently I noticed that three LEDs in my 05 SantaFe's high mount stop light glow even without the brake applied. When the brake pedal is depressed, the entire light glows as it should. But only the three LEDs glow at all times.
View 13 Replies
My Sonata suddenly started having front right brake sticking issue. It will happen only after an extended distance of frequent drive & stop. Something like Houston daily ride. So, after the traffic jam mysteriously clear and you can get some speed, starting at 40MPH a high grinding noise from the front (Ceramic brake pads) and the car feels very heavy. The sticking phenomenon will disappear if you wait a little with avoiding using the brakes.
I am going to check it today. So far I know that the sliding pins are not the issue. I recently cleaned them and lubricated them. The front right brake will get hot while the left are just in normal temperature. The brake pedal is getting higher while the sticking is about to happen and happening.
My first guess is the Flexible brake hose. Or maybe a bad caliper. I think if the master cylinder was the issue, I might have more than one sticking brake wheel. I don't know how common it is to have a bad ABS unit causing this issue. It feels really like a build up pressure caused by a valve effect of interior deteriorated brake hose.
View 26 Replies
So for the last month when I hit the brake pedal I've been getting a creaking noise in the pedal and the brakes don't seem as good. Within the last 6 months I've replaced the rotors, calipers and pads on the front and back. Starting last week when driving between 0-40 mph the ABS has started to engage on its own without even touching the brake pedal. So I've pulled the 2 ABS fuses and I no longer have the creaking noise when hitting the pedal and of course without the ABS its no longer engaging on its own. I've checked both the tone rings in the front and both of them are fine. I also now have a cel with code 0501 and I'm guessing that is because the ABS is currently disconnected. Is it safe to assume that the ABS Pump also known as the hydraulic electronic control unit has gone bad and needs to be replaced?
View 2 Replies
I have a 2001 f250 sd 4x4. For the past year it will blow cold air unless I'm in stop and go traffic then it blows warm air. Engin temp thermostat and water pump are fine. Yesterday it quit blowing all together and it really wouldn't bother me but where I live the morning temps and rainy days are causing the windshield to fog up and my defroster not even working. Where can I start to get this fixed.
View 7 Replies
Last week I noticed an erratic temperature gauge while I was in stop-and-go traffic. It would go from just below halfway to nearly the red in about 7 seconds, bob around, go down a bit, then up, back down to halfway and sit for a while, etc. etc. etc. I stopped, added a little water to the reservoir and car was fine for about 20 minutes but then it started up again.
Went I got home I checked oil and it was low. I added a quart. After this the car has been fine.
Until today. It did go into the red a couple of times and sat there for a few seconds. I was surprised there were no lights or warnings of overheating! I opened the hood when I got home and didn't get the impression that the engine was particularly hot (though the upper radiator hose was hot).
I read this might be caused by air pockets in the cooling system and I need to "burp" it by taking off the radiator cap, starting the car, running the heater, and then topping up the radiator when I see the coolant level go down.
View 40 Replies
It seems to have difficulty starting during stop and go like on deliveries. Also has problems after refueling. Is this caused by a faulty purge valve? If so where is it located?
View 5 Replies
With summer heating up so is the engine. Temp stays normal at freeway speeds but as soon as I hit stop and go traffic it shoots up. Water pump is two years old. I flushed the radiator and didn't get much gunk out. Both fans are running when the AC is on. If I shut the car off but leave the key on the fans do not run when the car is not. I can't remember if they used to or not.
2001 Pontiac Grand Prix 3.1
View 2 Replies
I have a 2003 Hyundai Santa Fe. Within the last 2 months or so I have changed my timing belt, spark plugs, and all belts that needed to be changed. I notice that when I am idle at a traffic light, the car is a little rough or bumpy. Is this normal for its age, or should I be looking at something specific.
View 11 Replies
