Recently I began hearing noise such as a rattle on the right front of the vehicle. It is a 2003 SF 2.7L front wheel drive with almost 180k mi. At first I thought the noise was from the Serp belt tensioner. Now I believe it originates from the compressor clutch.
Does the a/c clutch have a history with its bearings ? Is the clutch replaceable on the compressor or is this a single unit replacement ?
I have a '03 V6 3.5 Santa Fe. The clutch on the AC compressor went out and was making a loud racket. When I was pulling the compressor off I noticed the wire harness connection to the compressor was damaged. Either by me or previous change.
So the end of the harness on the car side is damaged. Can a new one be purchased and spliced? I cannot see where it goes to see if it can be replaced.
My '01 F-150 2WD, XLT has a foghorn sound coming from the left front side at idle after the 4.6L is warmed up. It goes away with an increase in engine RPM and is unnoticeable at hwy speeds. I have no codes (I have checked w/ my code reader). The service desk guy at the stealer said it is my abs pump going bad (I figured it was a pump of some sort, my 55 packard PS makes the same noise when almost empty-the system leaks). It also appears this is a stealer only part, and going to cost 6 or 7 benjamins to buy and probably another 5 benjamins too fix.
View 4 RepliesMy 97 regal has a noise from the compressor clutch. It goes away when the a/c is turned on. Mechanic said its the clutch assembly. Is this easy to change? What causes the noise to go away when the a/c is turned on?
View 6 RepliesI have a 2003 2.8 GLI and my compressor clutch will not engaged i provided the clutch with a direct power and ground from the battery and it engaged. i also went to the junk yard and got a couple of Fan Control Module ($4 each) and it still does not engaged.
View 3 RepliesI have a 01 f150 4.2L and a while ago the ac compressor clutch broke. I didn't catch it in time and the stress it caused on the belt broke the power steering pump pulley. So I replaced the steering pump and pulley and the compressor the accumulator/dryer and the office tube put the 134a back in and everything worked fine. three months later ac stopped working. I figured the condenser was bad so i replaced it. Charged it up still no cold ac. so i thought maybe the manifold that goes on the compressor was clogged so i replaced it. While I did that i said to myself well i should tear out the dash and replace the evap as well. so just about everything has been replaced on the ac system.
Aside from the cycle switch and the high side switch witch from my test both seem to be working. now here is the thing. the tube witch holds the office gets ice cold then goes to the evap but the suction line coming from the evap doesn't get cold and the ac blows warm air. this very problem is what convinced me that the evap was clogged and needed to be changed witch is why i undertook the task of tearing the dash out. in all it took 14 hours to do the whole job. now for the pressures that i get from the ac manifold low side goes 40 down to 20 ..... this is normal. high side is a little high. I charge it to 125 still no cold air. so i dump a little more 134 in. at 90 degrees high side pressure should be around 200ish i get it there still no cold air. I have just about replaced everything i can think of.
I've got a loud, intermittent, swooshing, vibrating noise from the front left wheel area at highway speeds. I put a camera down there and saw that when there was noise, the front driveshaft and front left halfshaft were spinning. When they stopped spinning on their own, the noise stopped. Hubs are Warn Premium (gold) and unlocked. Unit bearing already replaced. What could it be?
View 10 Replies2003 F350 4.4 5.4L auto. The front hub assemblies, seals, axle ujoints and upper/lower ball joint were all replaced. I bought all the parts gave them to the mechanic and told him if there's problems call me. I took a week off went to MS and he never called. I go to get truck he tells me, the bearings in the hubs are not spinning freely causing the axles to spin. I checked the hubs they are in the unlock position (Warn manual hubs). Originally auto hubs. Now i have the whole front diff spinning and the front drive shaft is spinning too. Clacking and clicking from the front wgen driving. Oh he said the front drive shaft ujoint was bad also. I paid $600 to have it all replaced and i get it back wrong. Is there something i need to check on the hubs that he maybe did wrong? Or is it possible i was sold the wrong hub assemblies?
View 14 RepliesI'm driving a 2002 Santa Fe (4WD, 6-cyl) without AC. The problem is that the compressor is dead and needs to be replaced - it was diagnosed by both a Hyundai dealership and a local repair shop. I understand that when replacing the compressor, you want to replace the receiver/drier and expansion valve and clean the system to remove any metal shards in circulation. What is unclear is whether or not the condenser also needs to be replaced. This is complicated by the fact that the receiver/drier is physically a part of the condenser. While shopping around, some repair shops said I would have to replace the condenser as well, and others did not.
My questions are these:
- Can I just have the desiccant bag inside the drier replaced, or do I need to replace the entire condenser + receiver/drier unit?
- If replacing just the desiccant bag is an option, is it still smarter to replace the condenser as well in case there is compressor debris lodged in there that can't be flushed?
I have a 2006 2.4l Santa Fe, has been diagnosed with failing ac compressor. Quoted exorbitant amount of money to replace. As far as I know, this vehicle was available without the ac option, and at this point I don't car if I have it or not, looking for the cheapest fix. Can I bypass with a shorter belt? Does it need to be removed completely, and if so, can it be done without affecting anything else?
View 8 RepliesI got a 2003 GTI 1.8t and the AC air is blowing warm. With the car on, AC on and fans full blast both rad fans turn on but compressor clutch does not engage. Took it to a shop and the mechanic said the system was full of refrigerant but that the compressor was not getting the proper signal and there was an electrical problem.
I check the power at the compressor and it is reading about 7 volts, which is low correct? That should be getting 12-13 volts correct? I also check the pressure switch over by the passenger side and it was getting 13v. What to check next to start ruling out causes? Any quick way to determine whether this is electrical or a compressor issue? I am limited in my abilities as far as electrical work goes.
soo a friends 03 f-150 w/ the 4.6 has noticed the a/c compressor clutch engaging while heater is on. clutch engages for about 3 seconds or so and kicks back out consistently but only w/ the heater on. a/c dose function property when using a/c functions... Is this normal or does something need serviced???
View 3 RepliesPretty sure the a/c clutch on my LT1 is going - making lots of noise when working and also when not.
I've heard on some forums that this could be a bearing? Is it advisable for me to replace the entire clutch or just this bearing?
Either way, I assume I'll have to pull the clutch for which I think I'll need two special tools:
(1) clutch holder tool to break nut loose.
(2) pulley puller.
The A/C in my truck stopped working last year, and this year I intend to fix it. I believe the problem is with the compressor clutch because it was making noise as it would engage or disengage. It was making this noise for a good year or so, and then one day the noise stopped and I have no A/C. So I am only assuming its the clutch.
View 4 RepliesVehicle is 1998 F150 with 194k. The battery is 1 1/2 yrs old and belts and alternator are original.
Yesterday morning my VHF and dog tracking eqipment started humming with the truck running. The hum on the tracking eqpt. only happened when I pointed the antennae over the direction of the hood with truck running. When I shut truck off everything is normal. Later in the day the battery light came on. The battery light would go off if I kept it over 2400 rpm's. The charge on the dash was normal but as I got closr to home last night it dropped to almost nothing and the lights were very dim.
I am thinking alternator. What I am confused about is the humming noise in the background. The tracking eqpt. is completely separate from the truck while the VHF is direct to the battery with an iline fuse. Bad voltage regulator?
03 Santa Fe, 2.7 L engine. No cooling happening. Compressor not running. Jumpered both sides of the triple pressure switch. Jumpering Low/high side resulted in slight increase in engine rpm, Jumpering medium side and something turned on (didn't get a chance to investigate) but still no clutch operation on compressor. Wondering what to try next other than disconnecting and dropping compressor ?? Checked AC relay on the bench and the coil operates and contacts close, so that's good. Also10A fuse before relay contacts is OK.
View 12 RepliesMy mother in law has a Santa Fe 2004 with a ~2.4. The AC compressor quit working over the winter. The AC compressor does not react to turning on the AC button.
I checked the fuses. I also tried changing out the AC relay with another one and it still didn't respond. The relay also didn't sound as though it was clicking over. The AC indiacator light is working.
Could it be the actual button has failed or is there a way to check if the button is functioning?
How does the compressor know to engage? Is there a place I can test 12v at the compressor?
2003 V10.. Can I replace the AC compressor clutch with out pulling the compressor out?
View 13 Replies2004 Santa Fe (GLS 2.7L)
First off, the A/C has not worked since I bought the vehicle used. I have checked all the SMALL fuses (10-25 amp) that can be easily determined good or bad, both under the dash and under the hood, so this basically rules that out (right?). I was unsure of how to check the larger, plug-like fuses under the hood. I am about 85% sure the A/C compressor does not engage when the A/C switch is pushed (yes, the light on the A/C button inside does come on and stay on). This is because I am unsure of which pulley is the A/C compressor and where exactly it is located under the hood. My research showed that it should be the bottom-right pulley when looking at the car from the passenger side, but I could be wrong on this. The fact that I just moved to Florida from the midwest a few weeks ago makes this a rather urgent problem.
Next, after a recent oil change there has been a harsh knocking, diesel-like noise coming from the front-right (passenger) side under the hood. Further inspection seems to show that it is coming from the area of the A/C compressor (or where I'm assuming it is). Again, I'm wondering if this is related to the A/C compressor. This noise is not normal, and has only recently begun to be a problem. It happens during initial startup, can be heard during acceleration, and only seems to quiet down a bit during idling after the vehicle has been warmed up. But it is now always present.
Finally, when fueling I have noticed that filling the car prevents it from starting! I am forced to shift into neutral and rev the car while simultaneously turning the ignition. This does the job, and once the car is started, it runs fine and the problem only ever happens immediately after fueling...any thoughts from the more "mechanically-inclined" out.
After 9 solid years of service, my a/c compressor finally failed. According to the shop, its leaking at the center seam of the compressor. If the system is charged, then the compressor will operate until the low pressure switch shuts it down. My question is this: Can this compressor be rebuilt? If so, where can I get the parts (I'm assuming the shaft seal is leaking).
Also, a quick search on eBay provides several compressors that fit my car; however, some of them are listed as HS-17 compressors and others are HS-18. My car (according to the A/C sticker on the hood) says I have an HS-18 compressor. Are these two interchangeable? I'm asking because if the current compressor can't be rebuilt, then I will have to buy either a reman. or new unit.
Car: 2002 Hyundai Santa Fe, GLS, 2.7L V6
On 2500 mile trip, no A/C last 400 miles and we're cooking
Compressor clicking on/off about every 5 secs, clutch smell. Seems to be turning okay.
I brought some tools, including a full socket set.
Can I pull the clutch and remove shims in the campground? Looking for a condensed version of how?
Worst case, how do I replace the clutch- of I can find a dealer with one?
Pulley and clutch fixed, but cycling on and off...adding freon?