Santa FE SM (2001-06) :: 2003 - Front Shaft On Vehicle Right Side Makes A Noise
Dec 31, 2011
The bearing supporting the half shaft on the vehicle right side makes a noise. I don't hear the noise in the wheel bearings so I believe the noise is isolated to the support bearing.
The SF has 175k mi. The right side cv axle was replaced and it had some looseness in it but it did not eliminate the noise.
Additionally, I don't discount that some noise is generated by the tires as they are not new.
2003 Santa Fe 6cyl ....
View 2 Replies
Advertisement
I thought that my front wheel bearing was bad but I removed it and it seems fine. The issue that I'm having is a continous vibration (noise) in the left front that gets worse with speed.The half shaft makes a noise at the point where the half shaft meets the steering knuckle and when I turn the shaft at the outer splines, the grinding noise is present. My question is, is the entire half shaft supposed to turn, even the outer diameter of it that would enter the steering knuckle, or is the shaft supposed to turn inside of that outer diameter? I hope I was able to explain my problem clearly/
View 6 Replies
On two separate occasions I have been getting a droning like noise from the right side of the engine and when moving the steering wheel it still makes that same sound but changes slightly and even after when the steering was moved back and forth it still wouldn't go away so I let the vehicle run for a short while it slowly and eventually went away.. what would that sound be from?
View 2 Replies
Got a 2007 Santa Fe CM (Europe) with 160k km. I'm currently trying to figure out how to fix the clunk noise in the front of the vehicle. I am aware about the TSB 12-DS-002 where they recommend changing the drive shaft washer, but since that's a lot of work I want to make sure that this is really the problem.
The noise is not always there. Sometimes you can hear the clunk when decelerating, but not always. You can also sometimes hear a clunk when going from D to R. It sounds like a driveshaft has some play, and a change in the direction of the force causes it to slam into the other side. However, you can't feel it, so there is definitely not a lot of force behind it. You can only hear it.
However, I asked some guys to shift between R and D while I'm outside so that I can figure out where the sound comes from. However, murphy's law, it didn't made any clunk. And after shifting between R and D for like 20 times I felt bad for my transmission and stopped it.
The clunk is not always there, just sometimes. It doesn't really make sense to me, if its really play in a driveshaft it should be always there? Also the clunk started at about 155k km, now I got 160k.
Is there any further diagnostics I could do?
View 5 Replies
What is probably a common Santa Fe issue. I have a 2005 V6 2.7L model which has traveled 81,000 miles (131,000km). The power steering is and has been working fine, but over recent week has developed 2 symptoms :
a) The reservoir overflows (see pic)
b) There is a whining noise when the vehicle is traveling and when turning the sounds modifies to more of pressure-release type sound. When the vehicle is stationary, the noise is very evident when turning the steering wheel (See video here : Power steering noise - YouTube )
Other things to report are that the reservoir is full but has not needed a top-up for months. The power steering pump appears to be leak free. I have a slow drip from the rack & opinion area (detected at Hyundai first service - about a few drips per day and they decided it didn't warrant fixing)
I have read on this forum the issue may be related to the reservoir filter becoming blocked and this ties in with the fact the rack and pinion has a known drip leak, but I never need to top-up the reservoir.
View 12 Replies
2001 Hyundai Sante Fe. When braking, I get a noise and the whole vehicle shakes. Exactly as if I were driving in snow and just slammed the brakes. The feeling & noise feels and sounds the exact same as if I were sliding...
I've replaced the master cyl originally just because today is the first day the issue lasted long enough for me to fully hear//feel the whole issue. It's normally brief.
View 3 Replies
When I start my vehicle, it makes a grinding noise, sounds like it's coming from the front of the vehicle, when I put into gear it stops. It started gradual and is getting worse. It's a 6 cylinder automatic, with 108 k miles.
View 3 Replies
I get this loud click noise coming from the front end of my vehicle when I apply the brakes. It seems to happen much more often than not, especially at low speeds. I can only describe it as some sort of loud clicky clanky sound, it's also a single sound, it doesn't go on and on and it only happens when I apply the brakes.
View 2 Replies
I noticed something while riding as a passenger in my 1999 Subaru Forester lately. I was riding in the front passenger seat with the window down, and noticed a strange "spritzing" noise coming from the passenger side front of the vehicle. The sound is very brief, about a second in duration. I heard this repeat several times as we went down the road, and decided to time it. It turns out that this sound occurs exactly every 33 seconds while the car is in gear going down the road! It sounds like a pressure relief valve going off....but what could it be?
View 2 Replies
I have a 2001 4 cylinder Santa Fe. And atm I'm trying to replace the balance shaft oil seal but am having major problems getting it out.
View 2 Replies
I drive a SantaFe 2005 2.7 engine....lately it has a gas smell coming out of the passenger side- front... how is this coming from?
View 1 Replies
After 9 solid years of service, my a/c compressor finally failed. According to the shop, its leaking at the center seam of the compressor. If the system is charged, then the compressor will operate until the low pressure switch shuts it down. My question is this: Can this compressor be rebuilt? If so, where can I get the parts (I'm assuming the shaft seal is leaking).
Also, a quick search on eBay provides several compressors that fit my car; however, some of them are listed as HS-17 compressors and others are HS-18. My car (according to the A/C sticker on the hood) says I have an HS-18 compressor. Are these two interchangeable? I'm asking because if the current compressor can't be rebuilt, then I will have to buy either a reman. or new unit.
Car: 2002 Hyundai Santa Fe, GLS, 2.7L V6
View 5 Replies
I have a 2005 crdi diesel santa fe that i have a strange problem with it starts up first time no problem in the mornings and can drive all day long. However if i switch it off and leave it sit for about a half hour no way will it start again until it cools off. It will start though with a push start instantly!
I got only one fault code P0340 cam shaft sensor fault, i replaces sensor and made no difference. Is this a common fault???
View 4 Replies
I have a 2001 Santa Fe GLS 4WD, I've had my Auto Transmission Speed Sensor replaced and will have the output speed sensor replaced to have speedometer/odometer and cruise control fixed. While having the first sensor replaced my mechanic noticed the Input Shaft Speed Sensor Connector (the plug on the wiring harness) was cracked. I've been looking everywhere for this connector. I don't want to buy the complete wiring harness because I've heard it is very expensive. I want just the connector. What is the part number of just the connector?
View 2 Replies
So I own a 2003 Hyundai Santa Fe GLS 2.7. I am the fourth owner and currently there is 168k miles on the vehicle. I purchased the car with around 110k miles on it and have had it for nearly 5 years now.
Aside from general maintenance I have never had a single issue with it, until last weekend. On the way back home from a road trip I began to notice a whining sound, and then very abruptly the car shook and I lost control of the vehicle and had to pull over on the shoulder. I was on the highway and was VERY fortunate to not have gotten into an accident.
After inspecting carefully I discovered my 4WD Drive Shaft was literally hanging by a thread. The knuckles were ruined, and in the process my Transfer Case and Exhaust System were all severely damaged.
View 13 Replies
I just got it and the gauge is showing a little hot. I took it in they found nothing. The fans runs almost all of the time. It even started running when I was sitting in my driveway with it in park (it was about 55 degrees outside at the time). I also hear some grumbling noise in the dash on the drivers side. It sounds like something is trying to work (the radio is off and it still makes this sound).
View 5 Replies
The driver's side coil spring broke, but here's the story.
When I found out there was a recall on my 2004, I called the dealership. They told me that they were not replacing the coils springs, they were only going to attach a brace or bracket in case the coil springs would fail.
Well, last night the coil broke and it was in the parking lot and not at 50mph on the road.
What about bracket fix? It was told to me that it would only prevent the coil from cutting into the tire, not fix it.
I am going to call Hyundai HQ this morning, but what should I expect? Is it unreasonable to expect to get a set of springs and have someone local do the work?
View 2 Replies
I opened the door yesterday, got out of the car, then when I got back in the door wouldn't close. I did end up getting it closed but it took a lot of force and there was major resistance. When I got out, there was no resistance top open about a foot opening, just enough to squeeze out. Any more than that and I would have needed a lot of force to get it open.
View 1 Replies
I have a 2004 Hyundia Santa Fe. The passenger front window will not roll down from driver side switch but will from passenger switch but then will not go up on passenger side switch. I found a broken wire on driver side and repaired it. I put a test light on the wires on the passenger side and used the driver switch and the test light lights when using the up button and down button! I have already put a new master switch in and tested all switches they all work!
View 1 Replies
2003 Santa Fe 3.6 V6 with ABS
The car sat virtually driven for a year before it was given to me. After 2 weeks of normal driving this past December, the power brakes completely went out. Had to drive the pedal to the floor to stop at even slow speeds. Took the mechanic and they replaced the Master Cylinder and both brake lines.
Shortly thereafter had an unrelated issue with a coilpack gone bad. Replaced coilpack and at that time replaced both sets of brake pads on the rear.
In January, started noticing grinding metal on metal from both front brakes. Took the mechanic and they replaced both calipers, rotors, and pads.
2 weeks or so later, after 10 minutes of driving the front brakes started dragging. The pedal would become extremely hard, and I could notice thew smell of the pads burning. Would have to pull over, put the car in park and pump the brakes to get the calipers to release. This would occur intermittently every few days. Pumping the brakes would always solve the problem.
Over time, the issue became worse, ocurring far more frequently. Around this time I noticed leaving the engine on in park while pumping the brakes would no longer solve the issue. I would have to completely turn the car off and pump the brakes to get them to release.
Started noticing around this same time that the left rear started grinding. The brake pads completely wore down in 3 months time. Too to the mechanic. Replaced caliper, rotor and pads.
Still having the same issue with the brakes dragging. One mechanic thought it could be ABS related and advised me to pull the fuse and the two breakers to diagnose. Still had the same issue, so put the fuse and breakers back in.
No mechanic seems to know what is going on with it, and I'd hate to have to replace all the brakes again as the problem goes untreated. Is it possible that the master cylinder or brake booster could be the issue? It's a brand new master but that doesn't necessarily mean anything, I'm told. Again, I can only get the brakes to release the pressure by pumping the pedal with the engine off.
View 1 Replies
I have a 2003 Santa Fe and it's been running fine except I just replaced my oil pan from damage from ice and just did front brake pads 2 days ago.( oil went onto the pads and caused a weird grinding sound) ...
After the brake pads were done it drove fine. I came home and the next morning I go to reverse and the truck will not move at all. I can go to any gear but it just will not move. I thought it could be the brakes were frozen because the front right was smoking after the pads were installed and had the guy who did them check it out. he figured it was a caliper on the driver's side and replaced it, but it will still not move. I am praying this is not a trans problem.
View 4 Replies
