Santa FE SM (2001-06) :: 2003 - Error Code P1159
Jun 24, 2014
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
View 2 Replies
Advertisement
I have a 2003 diesel GS Santa Fe, every now and then when driving the ABS light comes on, not very often but it does, if I switch the ignition off and restart it goes out, I had it on a fault finder computer and it showed code c1274, I think its something to do with the G sensor and the way it breaks (ABS) is it an easy fault to fix? What are the costs involved and will it affect the driving of the car, like I say it rarely comes on and I don't notice any change in how it drives.
View 1 Replies
So the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
View 3 Replies
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
View 16 Replies
I just joined the forum mainly to care of my dads 2001 Hyundai Santa Fe but also I got a check engine light on my way home from work last night.
From last night I saw that oil was all over the timing belt. Today I inspected it with a Coworker and his OBD II reader.
Error Code was P0455, EVAP - Evaporative Emission Control System Leak Detected (gross leak).
Now the oil leak is stronger since the oil spills is on hood (inside hood). I will make a picture tonight when I get home.
I personal think it's leaking from a tube/ valve on top of the timing belt (picture will show more tonight). Thinking of cleaning the timing belt area, then drive a little around or leave it in idle to spot where the leak is from.
Common issue? I googled around but since P0455 is a common issue (on my 9-2x as well) I couldn't find anything about this I am also limited from my search since I am currently at my work PC incl. strong firewall.
I will see if google let me find a picture...
View 3 Replies
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 Replies
My Hyundai Santa Fe 2006 V6 3.5L shows error code P2100. I cannot for the life of me find the ETS relay. Ive scoured the net but just found vague drawings and pics that didn't show ETS relay. I would also like to know is the ETS relay also known as the fail safe relay or is that a separate relay. Ive seen pics of the fail safe relay but none for the ETS relay. If there is such a relay, exactly where it is located?
View 2 Replies
I got an Error Code of U0D00. What this is or means. The scan tool says to refer to your manual but I don't have one.
What the vehicle is doing is that it will work fine for a while then when you stop (in park) the engine will rev really high and back down all by it self for example. It will go up to 3.5 and back to 1 rpm repeated. Then when you start moving the car it will continue to idle higher like you are pressing the gas. During all of this the check engine light will appear?
View 3 Replies
I have a 2003 Elantra GLS. I am intermittently Check Engine light and error code is P0113 - Air Intake sensor issue. I can't locate where the sensor is. I don't see any wire coming of the tubing that connects the air filter to the engine.
View 18 Replies
I'm getting an error code 2-7 (flashes two times, pauses, then flashes seven times) when my truck starts up. It does this cycle twice then stays on permanently. It has only started doing this since last night when I replaced my factory tape deck with a factory Cd player from a 2002 F-150.
View 14 Replies
I am having serious problems with my 2003 Santa Fe 2WD 2.7. First, about two months ago, I would have typical crankshaft position sensor problems whenever it would rain outside and my car would not start or if it did it would eventually stall while driving. Before stalling, the engine light would come on with code P0335 and the engine would shake. I did my best not to drive it during these moments and was always able to get it back home. The problem went away after a couple days of issues until recently.
About a week ago, the P0335 code came back with associated symptoms; however, this time it would not go away. It is worth noting however that I am in Portland Oregon and it is raining non-stop this time of the year. I am not a mechanic, but my neighbor used to be and he carefully guided me through replacing my Crankshaft Position Sensor, Camshaft Position Sensor, and several spark plugs.
After all of this work, my car turns over and starts for maybe a second, where before it would not even fully turn over in my driveway. It immediately dies after the second and then I can not get it to start up again unless I charge the battery for a bit or hook it up to another car and even then its only that initial second of start up. Additionally, there are no longer any codes or check engine light, but there is a "pending p0335" on my neighbors reader. I thought maybe my crankshaft sensor was defective, so I got a second one and it is still the same deal.
It is also worth noting that I do not see any tachometer movement during start up. When we replaced the Crankshaft sensor the old one was destroyed. The wires on it were either burnt up or the plastic coating had decayed away almost completely; thus the reason it was shorting out.
My car has all new belts done through a dealership as of 10 months ago, so I doubt it is related to the timing belt. My neighbor thinks it may be bad fuel, although I always get good fuel and I also doubt this is the case. During key-on you can hear the fuel pump start up and other components all working normally, so it is unlikely related to that.
View 7 Replies
Check engine light is on, when I went to get my car inspected it was showing an invalid vin code. How do get this off so I can get my emissions done?
2007 Santa Fe SE
View 3 Replies
I have a 2008 model 2.7 v6 with 80000 Km, and I would like to share my experience with several issues:
- Random misfire: brought the car to Hyundai, very bad response. I bought online the wiring of the spark plugs (according to them that was the reason of the misfire) and they installed it, did not improve. The car was still showing error code after clearing, and the fuel consumption at an average of 23L/100km.
- I then decided to change all the 6 spark plugs, no difference. The workshop told me the coils were in perfect condition. Still having a message like this: "ignition error on 2 or more spark plugs".
- I did a complete cleaning with contact spray of the MAF sensor.
- I bought online a couple of ignition coils, being original Hyundai ones, and changed them. When installing them i realized the existing ones were not original Hyundai and had a small marking, making me think they were recycled or chinese stuff.
- Having done that, the OBDII shown two more error codes: P341: error on camshaft position sensor, P2189: fuel idle (too much air, maybe caused by the first one). Changed both camshaft position sensors and then big change in the behaviour, more response, throttle, better gear switching.
- I so concluded that the 4 remaining coils have to be changed and ordered another time 4 of them online. OBDII showing now only one error code: random misfire. The engine going much better than all i got before.
- I have decided to take advantage of this order and also ordered a new TPS (seeing here that it was a common problem) and a Crankshaft position sensor (in order to prevent any other issue).
- I also changed previously 2 downstream o2 sensors that were giving an error related to emission. Emission here are not strictly controled so it is not a big issue.
My question is, what in all that sensors can more likely make my car burn 23L/100km??? Asian cities are quite similar to american cities, lots of highways. This consumption compared to what you describe is way over the normal one isn't it? I was assuming the ignition problem was the responsible, am i right?
View 54 Replies
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
View 12 Replies
I have an issue in my car (Santa fe 2011) and it occurred since it was new (ODO 3000 KM , ESP light is on and the 4WD Blinking) . the agency could not resolve the issue. and my car up to now been in and out from the workshop for more than 6 times . and more the error code ( C1627 ) that appears in the GDS(Global Diagnostic System) does not exist in the system (troubleshoot manual) .
View 5 Replies
I have a Korean spec 2014 Hyundai Santa Fe 2.2L R-eVGT 6AT 4WD. Around a year ago it started to go into limp mode i had it checked and the error code was p0488 (EGR) Throttle Control Circuit A Range / Performance.
It has gradually become more frequent to the extent it goes into limp mode within a a minute or so . so far the dealer has changed the EGR valve, TCM , the whole turbo assembly and it is no different. They have also stripped and cleaned the intake manifold and egr cooler.
View 6 Replies
So of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
View 2 Replies
I have Santa Fe 2002 v6 2.7 and it's have been in the mechanic for 2 months now.
Suddenly my gear box don't go up 3rd, the error that the diagnostic reader is P 1528. What it can be? How to Fix it?
View 2 Replies
keep on getting this error code....I think I have exhaust leak , Would that trigger this code ?....is an Exhaust leak is considered a Vacuum leak??
View 1 Replies
Still getting p0174 error after upsteam downstream, checked everything.
View 1 Replies
Have 2001 suburban with the 5.3. Mechanic has replaced EGR valve 3Xs. Error code specifies "replace EGR valve". Each time car runs fine for 4-6 weeks (500-1000 miles) and then service engine light comes on. Shortly thereafter the car will not idle correctly (under 1,000 rpm) and will die at stop. I think the EGR valves are getting clogged up with carbon. Car has 130,000 miles on it.
View 4 Replies
