Santa FE SM (2001-06) :: 2003 - Crank Position Sensor Blown


Sep 30, 2012

I've a 2.0L Santa Fe CRDI 4WD, 2003. My Crank position sensor has blown. My question is, does the timing belt have to be replaced with the sensor, or can the sensor be replaced alone? I know the belt must be replaced with petrol models but I've been told it may not be necessary with diesels.

View 1 Replies

Advertisement

Santa FE SM (2001-06) :: 3.5L 4WD Not Starting / Replaced Crank Position Sensor

We bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.

When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.

About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:

1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor

I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.

View 5 Replies

Accent LC (2000-05) :: 2003 - Repeated Crank Position Sensor Failure

I've got an '03 Accent 1.6 in the family. December 2011 I replaced the crank position sensor and it cured the no start problem. Got it from A/Zone. It lasted 2 years and 8 months. Then, the same thing happened again in August 2014 only this time the car stopped running while on the road and I had it towed to a local garage. They installed a "Standard" & was back on the road again when it stopped running again a week ago. Had it towed to my house this time and read the code. P0336 CPS again! That sensor lasted only 4 months. The garage came & replaced the sensor & it's back on the road...for now. Do these cars only play nice with Hyundai CPS's or should I be looking for an underlying issue?

View 7 Replies

Santa FE SM (2001-06) :: Crankshaft Position Sensor Replacement

After heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.

View 5 Replies

Santa FE SM (2001-06) :: Crankshaft Position Sensor Broken In Block

2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?

View 9 Replies

Santa FE SM (2001-06) :: 2004 3.5l Throttle Position Sensor Replacement

I have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.

View 2 Replies

Santa FE SM (2001-06) :: CEL Codes For Crankshaft Position Sensor - Random Misfires

I am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.

View 3 Replies

Santa FE SM (2001-06) :: Code P2125 - Throttle Position Sensor Replacement?

Getting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.

If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?

View 8 Replies

Santa FE SM (2001-06) :: Replaced Throttle Position Sensor And Now Idling At 2000 Rpms

2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?

View 5 Replies

Santa FE SM (2001-06) :: Taking Multiple Tries To Start - P0340 Camshaft Position Sensor Circuit Code

02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.

I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.

View 6 Replies

Elantra XD (2001-06) :: 2003 - CEL Code / Bad Camshaft Position Sensor

I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?

Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?

View 4 Replies

Golf IV R32 :: Crank Position Sensor Replacement?

How difficult is it to replace the crank position sensor? It looks pretty tucked away at the front of the engine. Just wondering how much time I should put aside for this job.

View 15 Replies

Phaeton :: Location Of Crank Shaft Position Sensor

Where the Crank Shaft Position sensor is located on a 2004 4.2 phaeton... Dealership want 360 to install it ...

View 14 Replies

Chrysler - Towncountry :: Crank Position Sensor Replacement

Everything I've found on replacing the crank position sensor on my 2002 5.8l Chrysler town & country says its on the bellhousing but its not there!

View 3 Replies

Ford Excursion :: Crank Position Sensor Location

Where does the CPS located on my truck? Knowing mine is 5.4 L 2000 model. 121,000 miles on clock.

View 6 Replies

Santa FE SM (2001-06) :: 2003 - Ignition Stuck In Start Position

I have a 2003 2.4L 5 speed manual Santa Fe. I was parking my vehicle and removed my key as usual and realized that the car was still running. I put it into reverse rolled back and back into 1st to roll forward just to make sure I wasn't dreaming. I ended up pulling the fuel pump fuse and disconnecting the battery to turn it off.

When I replaced the fuse and reconnected the battery I was able to bump start the vehicle without the key in the car and drive it all the way home with no problem. I took apart all the plastic pieces around the Ignition and attempted to remove the cylinder but was unable to locate any sort of small button or pin to push on to remove it. Where is the release button?

What are my options here? Do I replace the cylinder first or get a new key, or is there something else that I should check first before I take it in.

View 1 Replies

Rodeo :: 1998 Isuzu - Crank Shift Position Sensor

I have a 98 Isuzu Rodeo 3.2 V6 2 wheel drive I don't know where the crank shift position sensor is located. I don't have 310.00 to pay someone to replace this.

View 4 Replies

Accent MC (2006-11) :: Hard Starting - Crank Position Sensor

2007 Accent GLS, US-market, Automatic, 140k miles

This is my wife's car. She called me from the side of the road while I was on a job out of town. The car had stalled while driving. She was able to re-start the car with check-engine lamp showing and took the car directly to a garage. It ran normally during that trip.

The garage diagnosed the problem as a failed crankshaft position sensor. They cleared all codes from the ECU without telling us what they were. My wife told them I would fix it when I got home. She drove the car home, parked it there and used my car until I got back.

When I got home, I replaced the crank position sensor with a new beck-arnley part. It was a poor fit, but it did go in. Now roughly every other start takes a few extra cranks. It always starts. It does not stall once started. No check-engine light since the initial episode. I just don't like the random hard starts.

Normal fuel consumption & power output. All other maintenance is up to date.

View 6 Replies

Golf IV / Jetta IV :: Installed New Crank Position Sensor Now Car Will Not Start

After installing a new crank position sensor on my 05 GTI 1.8T would I have to recalibrate my ECM, my car will not start.

View 2 Replies

Accent LC (2000-05) :: Crank Position Sensor Shows No Resistance When Cranking

I'm working on a family members car. We pulled out the old motor and put in a new one because the old one has rod knock. We're not getting ANY spark. Crank position sensor shows no resistance when cranking. The harness at the crank position sensor shows no voltage. The both coils measure 1.5ohms.

The only two bits of the harness that are in questionable locations are the grounds next to the ignition coil and the passenger side strut tower ground. I have the strut tower one to the closest bolt on the intake manifold and the coil pack grounds to the coil pack bracket.

The car has plenty of fuel and good cranking speed, just no spark. I verified using a timing light (no flash) and spark-plug short-to-ground. The old engine WAS running and all of the sensors on this one were swapped over from the running one. Also, the tach doesn't move when cranking.

Is there something that's commonly overlooked, or something that could be causing the issue searching showed it could be the crank position sensor, but like I said, I pulled the working one off the running engine.

View 1 Replies

Golf IV / Jetta IV :: 1999 - Oil On Crank Position Sensor Making It Miss

99 2.0 jetta. Getting oil on crank position sensor making it miss. Is it the rear main seal? Only reason I can think to have oil around the flywheel... How hard is a rear main seal to change out....

View 2 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved