Santa FE SM (2001-06) :: 2003 - ABS Light Comes On / Error Code C1274
Nov 18, 2011
I have a 2003 diesel GS Santa Fe, every now and then when driving the ABS light comes on, not very often but it does, if I switch the ignition off and restart it goes out, I had it on a fault finder computer and it showed code c1274, I think its something to do with the G sensor and the way it breaks (ABS) is it an easy fault to fix? What are the costs involved and will it affect the driving of the car, like I say it rarely comes on and I don't notice any change in how it drives.
View 1 Replies
Advertisement
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
View 2 Replies
So the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
View 3 Replies
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 Replies
I have a 2003 Elantra GLS. I am intermittently Check Engine light and error code is P0113 - Air Intake sensor issue. I can't locate where the sensor is. I don't see any wire coming of the tubing that connects the air filter to the engine.
View 18 Replies
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
View 16 Replies
I just joined the forum mainly to care of my dads 2001 Hyundai Santa Fe but also I got a check engine light on my way home from work last night.
From last night I saw that oil was all over the timing belt. Today I inspected it with a Coworker and his OBD II reader.
Error Code was P0455, EVAP - Evaporative Emission Control System Leak Detected (gross leak).
Now the oil leak is stronger since the oil spills is on hood (inside hood). I will make a picture tonight when I get home.
I personal think it's leaking from a tube/ valve on top of the timing belt (picture will show more tonight). Thinking of cleaning the timing belt area, then drive a little around or leave it in idle to spot where the leak is from.
Common issue? I googled around but since P0455 is a common issue (on my 9-2x as well) I couldn't find anything about this I am also limited from my search since I am currently at my work PC incl. strong firewall.
I will see if google let me find a picture...
View 3 Replies
My Hyundai Santa Fe 2006 V6 3.5L shows error code P2100. I cannot for the life of me find the ETS relay. Ive scoured the net but just found vague drawings and pics that didn't show ETS relay. I would also like to know is the ETS relay also known as the fail safe relay or is that a separate relay. Ive seen pics of the fail safe relay but none for the ETS relay. If there is such a relay, exactly where it is located?
View 2 Replies
I got an Error Code of U0D00. What this is or means. The scan tool says to refer to your manual but I don't have one.
What the vehicle is doing is that it will work fine for a while then when you stop (in park) the engine will rev really high and back down all by it self for example. It will go up to 3.5 and back to 1 rpm repeated. Then when you start moving the car it will continue to idle higher like you are pressing the gas. During all of this the check engine light will appear?
View 3 Replies
I have an issue in my car (Santa fe 2011) and it occurred since it was new (ODO 3000 KM , ESP light is on and the 4WD Blinking) . the agency could not resolve the issue. and my car up to now been in and out from the workshop for more than 6 times . and more the error code ( C1627 ) that appears in the GDS(Global Diagnostic System) does not exist in the system (troubleshoot manual) .
View 5 Replies
I'm getting an error code 2-7 (flashes two times, pauses, then flashes seven times) when my truck starts up. It does this cycle twice then stays on permanently. It has only started doing this since last night when I replaced my factory tape deck with a factory Cd player from a 2002 F-150.
View 14 Replies
Mystery issue with my 2001 Accent GSI (5-speed manual, 1.6 L). I'm getting a P0300 error code and the Check Engine light (the light is like an old friend, I miss it when it's not on). This happened four months ago and I replaced the ignition coil - seemed to fix things - but now the light and the error is back with a vengeance. Car stumbles and runs rough. Changed the plugs and plug wires, but no difference.
BTW, there's a small pin hole in the upper part of the gas tank (just enough to give it a gassy smell when the tank is full) but I don't think the hole would be big enough at this stage to cause the check engine light to come on in the same way it does if you leave the gas cap off or loose.
View 3 Replies
Well, I bought a used 2003 Escape for my daughter and without thoroughly researching the airbag light, now have a problem. The light flashes twice, pause, then once, so I think this is error code 21? I cannot find anything on what this code is and how to fix it. I disconnected battery for an hour and now I get 4 flashes, pause, 6 flashes, 46 error.
View 1 Replies
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 Replies
I am having serious problems with my 2003 Santa Fe 2WD 2.7. First, about two months ago, I would have typical crankshaft position sensor problems whenever it would rain outside and my car would not start or if it did it would eventually stall while driving. Before stalling, the engine light would come on with code P0335 and the engine would shake. I did my best not to drive it during these moments and was always able to get it back home. The problem went away after a couple days of issues until recently.
About a week ago, the P0335 code came back with associated symptoms; however, this time it would not go away. It is worth noting however that I am in Portland Oregon and it is raining non-stop this time of the year. I am not a mechanic, but my neighbor used to be and he carefully guided me through replacing my Crankshaft Position Sensor, Camshaft Position Sensor, and several spark plugs.
After all of this work, my car turns over and starts for maybe a second, where before it would not even fully turn over in my driveway. It immediately dies after the second and then I can not get it to start up again unless I charge the battery for a bit or hook it up to another car and even then its only that initial second of start up. Additionally, there are no longer any codes or check engine light, but there is a "pending p0335" on my neighbors reader. I thought maybe my crankshaft sensor was defective, so I got a second one and it is still the same deal.
It is also worth noting that I do not see any tachometer movement during start up. When we replaced the Crankshaft sensor the old one was destroyed. The wires on it were either burnt up or the plastic coating had decayed away almost completely; thus the reason it was shorting out.
My car has all new belts done through a dealership as of 10 months ago, so I doubt it is related to the timing belt. My neighbor thinks it may be bad fuel, although I always get good fuel and I also doubt this is the case. During key-on you can hear the fuel pump start up and other components all working normally, so it is unlikely related to that.
View 7 Replies
I have an 2004 Santa Fe and im having some Mass Air Flow Sensor problems but I dont know what's wrong. My engine light came on for the second time after awhile. And I got it checked for the code and of course it was my sensor again. The first time I just giggled it around and the light went off. I did the same thing today with giggling it again went off. So I feel like it might be a loose connection but I really hope it isn't failing because im pretty sure that's uber expensive to fix.
View 2 Replies
2003 Santa Fe GLS 120K mi. 2wd, 2.7L, AT.
Been having for some time an intermittent problem where the air bag light will come on and not clear. I can clear it sometimes by removing the neg. batt. term. and letting it sit for a few minutes. The "air bag" light always seems to come on when someone sits in the passenger seat. The dealer reported a trouble code of "B1382-- PSAB harness improper pin tension" They said that they re-seated a connector and it was good to go. Now the "air bag" light is on again. Does the description refer to the pin tension in a connector? which connector does it refer to and can I just tighten up the female part of the connector such that the male pin makes better contact? Is it the yellow connector under the seat?
View 7 Replies
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 Replies
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 Replies
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
View 2 Replies
My check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
View 5 Replies
