Santa FE SM (2001-06) :: 2002 V6 AWD Check Engine Light Stays On After Replacing ECM
Sep 17, 2014
My 2002 Hyundai Santa Fe 2.7L V6 AWD failed to start a week ago. After towing to my neighborhood repair shop, it was diagnosed as a faulty ECM based on code P560 (System Voltage Problem). They replaced the ECM (along with relay) with a used one with the exact same part#. After that, the car was started and run OK but Check Engine Light stays on all the time. The codes displayed are:
P1529 TCU MIL Request Signal
P0501 VSS Range Performance
I was told that this is caused by the fact that each ECM is VIN/PIN locked. The replacing ECM was used in another car before and was locked with a different VIN thus cannot communicate with some components of the current car.
My questions are:
Can this used ECM be unlocked and relocked with a new VIN/PIN? If so, does it require the previous VIN/PIN to unlock? Most likely the previous VIN/PIN is no longer available.
Does this service require the presence of the car or can it be done with the ECM alone? Do keys need to be re-registered? The car starts fine currently.
View 11 Replies
Advertisement
I have a 2011 Santa Fe 3.5 6, FWD, 54k miles, that has been having the check engine light go on and off. Recently with in the pass month and a half the dealership has perform the recall adjustment, changed the manifold intake assy, changed the ECM with all visits rendered a P200A code. After changing the manifold assy, check engine light was off and fuel gage was at a 1/4 tank. Stop by a gas station and filled up and the light comes on. Remove gas cap after turning off engine and secured gas cap as directed on the cap of one click and light stays on. Turning into the dealership for the 4th time.
View 4 Replies
I have 2001 Wolfsberg Edition 4D jetta (gas) with 180,000 miles, manual transmission. The engine light has been on for years and years. Usually what I do is take it in for an oil change just before a smog. They re-set the codes. I drive it to my office and back and the light would stay off and I could smog it. Until recently. In April, I took the car in for an oil change. And when I picked it up, it ran terribly. It was lurching like crazy. I had to keep slip the clutch to drive it until it warmed up and the it would mostly start running OK. I took it back to my mechanic and he thought it was a timing belt. I had already changed the timing belt at 119,000 miles.
It seemed odd to me that this procedure needed to be done again after 60,000 miles, but I went ahead and had it done. That did not fix the problem. Then the mechanic replaced the air mass meter. That didn't work. Then he replaced the coils. That didn't work. My mechanic has had the car for a month and can't seem to figure out what to do. He keeps getting different error codes - codes that don't seem to make sense to him. The car needs to a smog (my registration date is June), but he can't smog it because we can't get the check engine light to stay off long enough.
View 9 Replies
I have a 2001 Chevy S10 4.3L. The CHECK GAUGES light stays on, and the oil pressure gauge stays at 0. The oil is full, and the engine runs and sounds fine. I drove it about 5 miles with no change. Up until now, the gauge has worked normally. Could it be the sending unit?
View 2 Replies
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
View 12 Replies
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 Replies
I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 Replies
I have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 Replies
I have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 Replies
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 Replies
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
View 2 Replies
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
View 1 Replies
2004 Santa fe- air bag light stays on-
Any trouble shooting protocol to follow?
View 14 Replies
I jump started my santafe becouse the battery was weak. After it started the check engine light on the dashboard came on and it stays on. What could the problem be.
View 1 Replies
My wife's car is throwing at p0306 code. I have changed the park plugs and the check engine lights comes on after 5-10 minute of driving and gives the same code. Can I move the spark plug wire to another ignition coil bank to test the coil? The picture shows the current plug locations on the ignition pack. Is there any certain order they need to be in or can I just swap 6 and 5 since they are the closest together?
View 6 Replies
I have a 2004 Santa Fe 2.4L the check engine light is on and says about the evap canister solenoid. I am trying to located it but I can't find it. So, where would it be located at so I can take it apart and where is the Canister located as well...
View 1 Replies
My check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
View 5 Replies
I have a 2004 santa fe with a 2.7 v6. I have had a little misfire issue lately. I had a major power loss with a check engine light on it lasted for just a minute before it settled itself out. Had the code pulled at a local parts store. P0301 so I checked the plugs and they looked worn out. I pulled the upper intake and replaced the plugs and wires plus the upper intake gasket. I cleared the code and that seemed to correct the problem. Two days later, same thing happened. The engine seems to be running fine now. I wiggled the wiring harness to the injector and to the coil, no change in the way it runs. I was thinking it could be an injector or a coil pack.
View 6 Replies
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
View 2 Replies
I have had a 2002 Prius since December of 2012, and it has been running fine since I got it; while it was in a wreck in May 2013 that has rendered both passenger-side doors and windows unusable, I have not seen that incident cause any other problems, and the car still runs perfectly fine. I am supposed to be driving from my current home state for a job soon, but about a week ago while I was driving on the interstate, the check engine light started flashing.
I was changing lanes and putting a good bit of pressure on the gas in order to pass someone that was going below the speed limit, putting my speed at around 80 mph when the check engine light started flashing. I started getting off of the interstate to find a place to stop and inspect things, but the light stopped flashing when I got down to around 45 mph on the exit ramp, and I was able to drive the rest of the way on the interstate without any trouble, even when I got in the 75 mph range again. The span of time between the light starting to flash and turning off again was probably about a minute or so.
View 7 Replies
2003 Santa Fe 2.7L, 2WD, 118K Mi.
This is a recurring problem. Air Bag light comes on and stays on. Seems to always get triggered by someone sitting in the front passenger seat AND the right side rear passenger seat. First couple of times I was able to clear it by removing the neg. battery terminal for 30 to 45 min. Then it stayed on and didn't clear. I took it to the dealership and they said they cleared it by cycling the connector behind the glovebox. It has been ok for a long time until yesterday night when I had 5 people in the car. Now this morning the "Air Bag" light is on and won't clear. I tried disconnecting the neg. battery terminal because it was easy to do but no luck. I have checked the connectors under the passenger seat thinking someone is bumping a connector with their feet but all connectors seem ok.
View 3 Replies
