Santa FE SM (2001-06) :: 2.4 Shuts Down After 2 Seconds - Codes P0100 And P0340
Apr 14, 2014
Left my 2002 SF 2.4 with someone to replace clutch. Calls me after the job to say it doesn't run!
Codes P0100 and P0340.
Maf is new. I had a Cam sensor in stock. Nil fix.
Have changed out recently;
Fuel Pump
Coil packs
CPS
MAF
and just now, the Cam sensor.
It starts right up then shuts off, does not slowly sputter and die.
I asked him to go over the wires and connectors. He could have stressed a cable while pulling the tranny. I do have the old MAF that I could try, but doubtful it would fail at the same time as a clutch job. Now wishing I had done the clutch myself!
View 1 Replies
Advertisement
2002 Santa Fe 2.4L Automatic. Driving on the freeway when it lost power. Couldn't go over 65 even with the accelerator all the way down, even slower on uphill climbs. The engine wouldn't rev higher than around 3000rpms.
I figured it sounded like a loss of power due to weak fuel pump. I replaced it as well as the fuel filter, and verified it was pumping. Put the car together, and still the same loss of power. Drove home and parked it, but next morning it won't run at all. It cranks all day long but doesn't fire.
So far, I have made the following repairs and checks:
-Verified catalytic converter was clear and not plugged
-Verified fuel pressure
-Checked spark plugs - all are good and gaped properly
-Replaced crank position sensor (With the code, I thought this would solve it)
-Verified timing belt and cam belt in time - both have also been changed recently
-Checked all relays and fuses
-Battery and alternator are good - both are new
I still have a crank no start issue, and I'm going crazy taking things apart and putting them back together only to have this car not fire.
View 13 Replies
I have a 2005 crdi diesel santa fe that i have a strange problem with it starts up first time no problem in the mornings and can drive all day long. However if i switch it off and leave it sit for about a half hour no way will it start again until it cools off. It will start though with a push start instantly!
I got only one fault code P0340 cam shaft sensor fault, i replaces sensor and made no difference. Is this a common fault???
View 4 Replies
So my wife was driving our 2002 santa fe 2.7L and it shutdown. I went with the scanner and saw one code, P0340. I towed it home, changed the Crank Position sensor, which really sucked. I put it all back together and still no start. Same code.
View 15 Replies
I replaced the MAF a week ago but the code P0100 is still there. Car runs fine in the highway but I do notice acceleration issues. I got the knock sensor but I cannot find it in my nissan altima (2000). The car shakes while stalling, at a red light, and pretty much as soon as I stop. Putting the car in N will work a bit but won't stop the shaking. Should I focus on the MAF again or should I keep trying to replace the KS? Where it is?
View 3 Replies
The wifes camry all of a sudden tossed up CEL. Codes read P0100, P0110, and P0420. Car has about 125K miles, runs fine. I cleaned the MAF sensor with CRC cleaner just for that, pulled EFI fuse to reset, came back on immediately when started.
I was thinking of getting a used one from pull-a-part, but they only have 98 camrys at the moment. Any chance MAF is the same?
View 3 Replies
Check engine light came on yesterday evening. Advance read the codes as P0100 and P0171. The guy said something that it may be related to the mass air flow sensor. The car seems to run fine.
View 2 Replies
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
View 6 Replies
3.5L v6 173k. Engine shut down twice while driving. Started right up each time. From what I have seen in the forum it could be the Crankshaft Position Sensor. If it is the CPS, should I have the timing belt done at the same time?
View 4 Replies
At around 100K miles started to get the dreaded P0340 and P0344 that occurs randomly - engine cold, engine hot, rainy, hot, cold, you get the picture. Only occurs at startup. Shutdown/Clear Code/Restart and all is well for days... otherwise the engine runs fine. Have replaced the CMP sensors, thoroughly cleaned CMP and crankshaft sensor connectors, even replaced the alternator. I would like to tone out the wiring back to the PCM connector pins. I am trying to find a pinout diagram. PCM is 7L3A-12A650-GKF.
View 2 Replies
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 Replies
Every time i stop for gas..my 01 santa fe is hard to start..it would take 4 to 5 start before she goes, then i have to keep the rpm up, bring her to idle..after that shes ok, till the next fill up.. the only way around this is to keep her running while gassing up..while filling up she run rough idle, some time engine shuts off..then its hard to start..
View 5 Replies
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
View 14 Replies
My car has the same issue, its a 2001 santa 2.4 . Its starts and then shut off after 3 seconds. camshaft was replaced twice already. still same issue, die after 3 seconds. everything seems to be fine.
What about fuel pressure at the rails? If the pump runs for a moment when the key is turned to the on position then when cranking it stops. That would let the engine start and run for about three seconds. Could it be the ignition switch?
View 9 Replies
I have an Air Conditioning issue on my 2004 Santa Fe, 2.4L 5-speed manual with 208,000km on it. I've never had any work done on my AC since I bought it new. Never had a problem with it and even as I write this is works just fine and blows ice cold air.
The problem started a couple of weeks ago when I noticed this very brief "higher pitched burping sound" coming from under the hood that lasts for just a second, and only when the AC is on and only if the RPM's are above idle. It sounds like a "bloop" for lack of a better description. When it happens, the RPM's drop one mark on the RMP gauge for a moment and there is obvious strain on the compressor. Air remains ice cold, everything still works, but this occurs every 30 seconds or so while driving.
While stopped I can rev the motor to just above idle, say 2000rpm and engage one of the defrost settings and get the "bloop" sound to occur almost every time. The top thicker AC pipe leading into the firewall from under the hood (the one that gets cold to the touch) seems to be part of the problem. At least if I am touching this pipe when it makes this "blooop" sound I can feel the vibration from the "bloop" in this pipe.
I've already had a garage replace my AC belt which I just had replaced a month ago, and checked the pullies and tension and all is okay. So it's definitely coming from the AC system and I can feel a vibration during the "blooop" sound on that pipe that gets cold and goes through the firewall. The sound does not occur when the AC is not on.
Also, when I am driving and it occurs every 30 seconds I do feel a slight decrease in the smoothness of the ride and like I said when it does this the RPM's will drop one mark on the gauge, which I'm assuming is the strain on the motor trying to engage the compressor when it's probably already up to pressure.
View 2 Replies
My beloved Hyundai Santa Fe,2006 model's engine light came up. The engine starts and than about 10 seconds after cuts out straight away. What to do. I have always taken care of this car and being serviced well.
View 23 Replies
I'm having this cold start issue with my 2001 SF, but it doesn't seem to be fuel related like as the car starts fine but after about literally 1-2seconds the RPMs drop below 1k and the car will stall if I don't put my foot on the accelerator and keep it around 1000-2000 RPMs. But if I happen to make the revs go too high and let them drop again it seems like it wants to stall even easier. After about 30 seconds it smoothens out and drives almost perfectly except for a slight lack of power than normal going uphill (A.T drops to 2nd gear, sometimes 1st depending on the incline). We have had the coolant temp sensor and the fuel pressure sensor replaced. Could it be the MAF? We did clean it one time but it didn't seem to work much at all. Recently out of curiosity, I disconnected the MAF sensor and started the car it being started for a few days. No issue with idling whatsoever!.. ??
View 4 Replies
2002 Sante Fe, 2.7L Belt squeals for about 10 seconds when the vehicle is first started up (engine cold) in the morning. Doesn't do it any other time until next morning. I had this problem 6 months ago and replaced the belt (OEM) and Dayco Tensioner. Now I have same issue again! What gives?
View 6 Replies
CEL has been on for a few months, emissions testing came up so we read the codes (P0401 & p0401p) . We took it to the mechanic we always go to, a local one and they ran a full diagnostic and they said there were no leaks and no build up. Everything checked out fine and all they could suggest was replacing the Solenoid (Don't get me started on that) they said they were baffled (a wee bit worrying). So we did that and 20 minutes later the light was back on . In fact, every time we reset the code it comes on 20 minutes later.
The car is due back for Emissions in a month since it failed.
View 3 Replies
I have a 2006 Santa Fe with the 3.5l, AWD, 5 speed auto, and 65,000 miles. Its a daily drive. Out of the blue it won't start. It cranks, but it won't start. The battery is strong and it has 1/2 tank of gas. I figured my code reader would solve the mystery, but it's doesn't produce any error codes. With no codes I don't even know where to begin.
View 4 Replies
