Saab - 9-3 :: 2006 - Engine Seems To Miss Multiple Cylinders When Idling
Oct 10, 2014
I am having a problem with my 2006 Saab 9-3 Aero Combi Wagon w/130k miles. When idling, driving up hills, and accelerating to pass, the engine seems to miss multiple cylinders. I've had all spark plugs replaced within the last year, and all the cylinder coils were checked after bringing the car in for this problem (one was replaced). I took the car in yesterday to address this problem and the mechanic stated that he didn't know what to do. The check engine light is on, and the mechanic told me that the readout states that their might have been a problem with the gas cap, but they checked it out and it looked sound. Could this be a fuel pressure problem? spark plug wires?
View 5 Replies
Advertisement
I have a 2006 Saab 9-3 Aero that I bought back in August. Two weeks ago, I brought car into the dealership for a 90k road service. It had some idling issues (sometimes, upon starting it up (cold or not), the car would idle and sputter, but never actually die. During the tune up, they said there was a frayed cable, which they replaced.
Fast forward 1.5 weeks later. The check engine light has come on. And the car is now sometimes idling funny just as it was before, only now it actually sputters and actually dies sometimes upon start up. After it initially dies, if I start it up again, it runs fine up on the second start.
Took into the dealership this morning and after 2 hours of diagnosis, they say the check engine read-out is indicating the fuel pump pressure sensor is going out, and that's what's causing it to idle and stall. Is this diagnosis legit?
View 8 Replies
I have a MK4 Golf 2003 1.9Tdi PD100 , the problem is that the engine seems to miss when idling , so the question really is how can I tell which cylinder is missing , it seems to do it every 10 seconds or so and the engine shakes slightly at the time as if it were missing ! .
I suppose it would be easier if the cylinder was missing all the time , then maybe I could crack open a line at a time ! , but can you do that on a PD engine !
View 1 Replies
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
View 14 Replies
My 9-2 is misfiring on cylinders 2 and 4. At first we suspected a timing issue but that doesn't appear to be the case. My mechanic is looking at it but can't seem to locate the problem... so far:
- replaced old spark plugs
- checked the coils (moved them to see if the misfiring followed the coils--it did not)
- checked the timing belt (all good)
- compression is good
- fuel coming in is rich
He's dropping the exhaust today to check things from that end... A faulty mass airflow sensor wouldn't effect specific cylinders would it? and we'd see a degradation in the fuel richness right?
View 5 Replies
I have 2000 b5 passat with 150k on it. I've had the problem of a multiple misfire on cylinders 2 and 4. The last time it happened was about a month ago do I brought it to a vw dealership and had one of their mechanics and they told me I had a valve cover gasket leak and it was causing my coil pack to short out so they replaced my coil pack, plugs, and wires. They wanted way too much for the valve cover gasket leak so I decided to wait till I more money. The car ran great for a month or so then the misfires started happening again.
I made an appointment to get my valve covers replaced a they're getting replaced right this minute but the misfires are coming and going. One day the car runs great and the next day it's misfiring like crazy an shuddering bad. It only seems to happen when it rains or is wet outside.
View 3 Replies
I have a mysterious problem with the BMW 335d concerning the engine. The dealer detected a "miss" in the cylinders based on the check engine light, but there is no real drive problem. However, I have noticed a slight hesitation and noticeable reduction is fuel mileage. They don't really know what it is but suggested replacing the fuel injectors, in case that is the problem. And if not, maybe it needs cylinder head replacement. That seemed to be a rather expensive (for me) way to diagnose the problem. I can't believe that BMW somewhere has seen this problem before.
View 4 Replies
I have a 2001 1.8T Passat. I bought it used recently and have had tons of problems. I have been getting a lean air code for some time now and I think I recently resolved that. I had to replace a few vacuum lines, MAF, exhaust flex pipe (it was broken), fuel filter and fuel pressure regulator. The car was still running bad and throwing a lean air code (Bank 1) so I finally changed the O2 sensor and I think that did the trick. Now every time I start the car I get misfires until is warms up. I get misfires on all cylinders along with the multiple misfire code.
View 5 Replies
So my 2008 accent is my daily driver. I'm nearing the 300,000 mile mark but the last 100,000 miles have been plagued with random multiple misfires. I have changed the cables, crankshaft sensor, plugs, and I've been through numerous costly coils (I keep 4 with me). All listed parts were most recently changed at the same time. Why do I misfire on nearly every commute and get stuck operating on 3 cylinders?
View 11 Replies
Apparently yesterday (no known reason) my sons truck started to develop a miss (so it feels like to me).
2005 f150 5.4 auto 215000km 4x4 stx. No specific cylinder codes. All general codes.
P1000
P1464
P1550
P1703
P1780
None of which I can see causing the miss. No check engine lite, no other codes. Not sure what to look at next. I am starting to disconnect the coil packs one at a time and see if I can pin down the cylinder.
View 4 Replies
I'm getting Codes: P0300-306 (Misfires) and P0356.
I have researched the definitions of these codes and see that P0356 indicates an ignition coil failure on coil "F" (which would be Cylinder 6?)... but how is it possible only one coil is failing but I'm getting multiple/random misfires on all cylinders?
I've looked at the wiring diagrams and the only place that I can see a "single point failure" that can cause such a thing, would be the ECM itself...
View 14 Replies
2007 Passat 2.0T ... I just purchased this vehicle and after about two weeks of driving it has gone bananas. I found a ton of oil in the spark plug holes, and installed a new valve cover gasket...It no longer leaks. I am getting P0171, P0507 codes and multiple misfire codes from all cylinders...
View 6 Replies
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 Replies
I have a 2003 ford ranger edge with the 3.0l engine. It started acting up today so i brought it to get checked because the check engine light came on. Three codes where pulled p0300, p0306, and p0313. They were multiple/random cylinders misfiring, cylinder 6 misfire, and first misfire at 1000 rpm. I have replaced the plugs and coil and still have the trouble.
View 5 Replies
Its a 1994 with 4.0, automatic, 4x4. Running fine, parked it, a week later I'm getting a bad but sporadic miss that according to the stealership is the 3 cylinders on the right bank dropping in and out. Driving down the road you can feel them drop out and when they come back its a kick in the pants like a turbo kicked in.
Shop says wires are good, plugs are good, and then lost me when they started talking around in circles and not making much sense.
What could make 3 cylinders all on the same side of the engine drop in and out? This wasn't anything that slowly came on. Fine one day, crap the next. The only thing I did prior to was replace the IAC because it was idling high, it was cruddy inside, and it looked like it was original. It was running fine after that till this issue popped up out of nowhere.
Mileage was claimed to be 178k but I'm beginning to suspect it's probably 278k.
View 7 Replies
I have a 2012 F250, 6.2L, Crew Cab, FX4 with a little over 77,000 miles on it. I bought it used from a Ford dealership last summer. Prior to now, I've only had one issue with it and that was squirrel/rodent induced. Something chewed through the wiring harness right before the connection to the #7 cylinder. There was enough left over wire to solder it back together and put heat shrink around each wire.
It ran fine up until last weekend. The wife and I went to a store, she was driving and parked like a total jerk right in the front area of the parking lot. When we got back in the truck, she started it up and it was just running rough with hardly any power. My first thought was someone dumped something into the gas due to her amazing parking, but there were no smells or residue of anything near the gas cap when we got home only a couple miles away.
When I got home I ran my code scanner and found 300, 301, 305, 307, and 308. I dumped a bottle of ISO-Heet in it, let it sit for a bit then cranked her up and ran it for a few miles to the gas station and filled up...about 25/26 gallons, I don't remember...I was a little above 1/4 tank when this all started. No change in performance and the codes were all still the same. I pulled the MAF, it looked clean, but I wiped it down anyways and threw it back in. No change. I then changed all the plugs. This took care of 301 and 305 but 300, 307, and 308 were still coming up. I then picked up two new coil packs for cylinders 7 and 8, threw them on and still no change.
I sat with it running on a flat surface for a little while revving the engine randomly for about 15 minutes, during this I noticed a fast tapping noise at about 3400 RPM, it went away quickly with no changes in the gauges on the dash. I cant really tell where it's coming from, but kinda sounds like its under the middle of the truck. While sitting there I ran the codes again, and now its back to 300, 301, 307, and 308. I'm now at a loss of what to even look at...
I've also checked the voltage coming off the harness at the connector to the coil packs...just under 11 volts. I've searched all over for what that voltage is supposed to be, but have failed miserably in my searches.
View 6 Replies
2005 Saab 9-5 ARC 2.3T67,000 Miles
Noticed a problem 2 weeks ago with my little Swedish meatball while at a red light on the way home. While idling, the car just shut off. I'm assuming it was a stall, but the car did not sputter and it was idling at around 900-1k RPMs but then just cut out. I put the car in park, and it started right up without issue and I drove the rest of the way home with it running fine. A couple days later, the same exact thing happened.
I took it in to my local Saab shop for a radiator hose replacement and an oil change. I told him about the stall/cut out problem, so he hooked up the Tech II but could not find any trouble codes. So he did a software update to the computer and told me to monitor it and call him if it happens again.
After getting my car back, it ran fine for a few days. I tried to get it to stall again by just letting it run in idle for 10-15 minutes but it wouldn't cut out. One night, I went to the gym for about an hour and came out and my car started right up and I drove about 5 minutes and came to a light. Car cut out again. However this time, it did not start up again. The engine would crank, the computer would go through the checks and give me the Check OK but it just wouldn't turn over. I tried to start it 5 or 6 times but no luck. I got out and pushed it to the side of the road. After about 2 minutes for sitting there, I tried it again and it turned over. Started right up like nothing ever happened.
The car drove again fine for a few days and then yesterday it cut out again. Same thing. Car would crank but not turn over. I let it sit there for 2 minutes (as traffic was going around me at a red light ) and then tried it again. The engine turned over but it did not start up fine. It definitely stuttered as it was trying to start and I had to give it some gas to get it running smoothly.
Couple of observations: This has only happened while idling (in Park or Drive)This has only happened when the car was warm. I've never had an issue starting in the morning or before the car warms upThis appears to only occur when it has been warm outside. (We've had a few days in the 60s here in PA)The Check Engine Light has never come on. So no trouble codes have ever been logged.
I've been searching the forums and most people seem to recommend replacing the Crank Position Sensor (my mechanic wants to do this as well). However from what I understand, if it was the CPS the car wouldn't stutter like it did when starting after a stall and wouldn't the CPS cut off the engine while driving as well?
View 3 Replies
I am looking for a honest, (if there is any such thing) mechanic to keep my 2002 Saab 9-3 running. I am currently experiencing a loud noise while the car is idling. This is my only means of transportation and I cannot afford a car payment at this.
View 19 Replies
Car was idling and driving real rough and dying at stops. Turns out that the transmission mount was torn so I replaced it and verified that the other two motor mounts were good. Car was still running rough but on a drive with some jerky shifts (automatic) after about 20 miles all is well and I'm running as smooth as a baby's bottom with great turbo action. Cars just don't fix themselves. What could have been wrong? By the way there were no codes from the Tech ll. Using a pc of tubing I can't hear any vacuum leaks nor when spraying brake cleaner on the hose ends does the engine race.
View 3 Replies
I have a 2004 Cadillac it started to miss when your idling, a check engine light when on and it was #5 plug not firing so I changed the plugs in front 4 of them and also bought a coil pack and replaced that, but it still misses. What else can I check before thinking its a sticky Valve or internal engine problems.
View 6 Replies
I have a '06 Passat 3.6. I had the intake and valve cover off the other day and when I put it back together it started missing bad. The code it is throwing is a P0300/ random/multiple engine cylinder misfire. What is wrong?
View 2 Replies
