S-10 :: 2002 Blazer Has Power But Won't Crank / Start
Apr 28, 2016
Went to start the truck, turned the key - dash lit up, fuel pump primed, turned the key all the way and nothing. Truck did not even try to turn over, headlights did not dim, no starter, no crank.
I checked/tested the following:
-Battery and terminal connections - good fully charged 12.3v
-Ran battery charger on slow charge 10-15 min (quick) to full 13v
-Wiring to starter - good
-Relay box under hood - has power
-Starter relay - has wiring diagram on it - tested good.
-Every ignition related fuse in the relay box - all good
-Every ignition fuse in the driver's side dash fuse box - good
-I wiggled the ignition switch while turning every possible way - no crank
-I ran the gearshift lever through all the gears, tried to start it in neutral - no crank
-Rolled the truck a little, put in park - no crank
For some reason I decided to double check the # 24 RDO IGN fuse - it was fine. With the fuse still out I tried to start the truck and it STARTED!
I turned the truck off, replaced the fuse and the truck started again and, so far, ever since. I do not think the # 24 fuse had anything to do with it; I just got lucky.
View 11 Replies
Advertisement
2002 Chev trailblazer, I have had the throttle body cleaned.... Sometimes after short stops, my vehicle will not crank, some times I have to step on the gas several times and it will finally crank, it sets no codes, no check engine lights come on. If it sits overnight, or for more than 20 minutes it cranks right up.
View 3 Replies
For about two weeks, my Blazer would crank but not start on the first turn of the key. After a couple of tries it would start and as long as the engine was not off for more than a few hours, it would start again with no problem. While driving however, the engine would periodically "hitch" like it was missing a spark, or not getting any gas. As of last weekend, the engine will not catch at all, and a light on the dash shows "low fuel" even though the tank is almost full.
Spoke to a mechanic who (without looking at it) diagnosed a fuel pump problem at a cost of around $1,000. Is there any other problem which may cause this issue? I have very limited mechanical ability, and cannot pull the spark plugs to test them, as they seem to be buried in the lower half of the engine block.
View 5 Replies
Wants to crank. I notice when I turn the key switch on (not start) the gas gauge pegs out as if a super full tank and no fuel pump noise. At times, leading up to the crank but no start condition, I would turn the key on, hear the fuel pump and the gas gauge would indicate proper fuel level. When this happened, the vehicle ALWAYS started.
Here what I know now;
1. Fuel pump works. As indicated by the red auxellery jumper lead inside the engine well.
2. Good fuel pressure.
3. Starter checks good.
4. Battery hot and leads are cleaned.
5. Grounds in engine compartment and at fuel tank are cleaned.
6. Vehicle does have gas.
7. Air bag light stays on, even after pulling battery leads, letting set, and reinstalling.
This ABS light would come on and go off independently before the "crank but no start condition". So I'm assuming that the ABS might be its own problem; but not contributing to the crank but no start condition? There were problems leading up to the no start condition. Vehicle began to become hard to start (but would start). After starting (at idle) if the gas pedal was pressed aggressively, the "service engine" light would flash on and off rapidly and the "ABS" light would come on. At this point the vehicle wanted to die. No apparent codes were given.
Now the "crank but no start condition". Before this problem, the vehicle was sending the code for 3 o2 sensors. But a new fuel filter corrected this problem completely with no further apparent problems. Then (about 4 weeks later) the "crank but no start". I do not think the fuel filter and the "crank but no start" problems are related.? No other maintenance has been done to this vehicle that might cause this problem. At this point the manual I am using is useless...
View 14 Replies
I have a 2002 F-250 with a 7.3.
I have been having a no crank, no start issue off and on for a while. batteries are new, cables are new, connections are clean, and starter has been rebuilt and checked. I bought a "starter relay" which i thought was the top solenoid in this picture. I also replaced the lower solenoid in the picture. The bottom solenoid was replaced with what im sure is the correct replacement. The upper I think is wrong. It started but then shut down and will not restart. The upper solenoid also was very hot after it shut down.
Long story short what is the upper solenoid for? Im assuming its not the starter solenoid. If so where is the Starter solenoid on a 2002 7.3?
View 14 Replies
I just got delivered a 7.3L from down south. Batteries were dead so replaced both. Fuel was a couple notches above red line (much closer to red line than 1/4 tank) so I added about 7-8 gallons.
It will crank forever and ever...Won't start.
With starter fluid it starts but not strong enough to pump the pedal and rev it up to keep it idling.
I know s-fluid is bad but if I continuously spray with key turned forward it will run but as soon as I let go of key it shuts off.
20 degree weather and it was delivered to a parking lot so I cannot plug it in.
Was told to check filter cap, turn key, and see if it fills bowl with fuel....if not then it is fuel pump. Someone else mentioned that it could be bad crank position sensor? Does this sound like fuel pump?
View 2 Replies
I have an 02 Blazer w/ 110K miles. It's the 4.3L with 4WD. When I start it in the morning it usually has a low pulsing whirring sound for up to 30 seconds. It then goes away until the car is parked for a long time again, say overnight. It's a low volume sound, a lot like the sound of off road tires running down the highway. This has been going on for several months now.
All systems work fine. The alternator is new, the water pump has about 29K on it, and the top idler pulley has been replaced. Turning the A/C on or off makes no difference. The sound is loudest when you stand in front of the passenger side headlight which made me suspect and swap the alternator.
Could it be the belt? It was replaced with the WP and the ribs are not smooth inside. They are notched. I assume that's to improve the flexibility of the belt. If I take it to a shop they'll get 30 seconds each morning to diagnose it.
View 7 Replies
What would cause my truck to have a long turnover start, a really rough idle, and a loss of power after idling at a stop light for about a minute?
This problem gets worse as the truck warms up. It feels as if I'm not getting power from all 6 cylinders but this goes away after about 20 feet of acceleration. The truck has never not started. It just has to turn over for about 5 to 10 seconds before it fires up. I changed the spark plugs and wires thinking it was that and then i tried the fuel filter and it wasn't that either.
View 8 Replies
Replaced battery. It seems to crank fine and I can definitely hear the pump kick in for a couple seconds at first, but just will not start. It sat for several days in cold weather. Based on what I have read here I am thinking it is the fuel pressure, and that I need to get the tool to check that. There is about 1/4 tank fuel now, it seems that once before when it sat for several days around 1/4 tank it started and ran rough, then ran fine after I filled the tank. Could it be as simple as filling the tank?
View 14 Replies
I have a 2002 chevy s-10 pickup, 4.3 V6 vortec, 4 wheel drive. It has developed a crank-no start when it's wet outside. Snow, rain, even high humidity.
Things already done: cap/rotor/wires/plugs; coil; fuel pump (fuel psi between 45-55). There was an issue with the distributor being chewed up by the cam - cam gear was inspected and is supposed to be in good shape. A used distributor was installed by the local shop. Engine has 200,000 miles. I was told the timing chain is a bit stretched but there is no timing problem.
Good power, smooth idle, no smoke and there is no engine codes generated by the crank-no start problem. I have power to the coil when it's happening, fuel in the system, even have a spark out of each cylinder wire but it still won't start. I think the car is possessed!
View 2 Replies
2002 V6 Camry no crank/no start.
- Turn key, starter relay clicks, clock dims (headlights do not), no crank/no start.
When I arrived the battery appeared new, the connections clean / tight and I could put my hand on the starter relay and feel/hear it click. With a brass bar and hammer, I gave the solenoid a tap and the car started right up. We shut the car off, no start again, tapped the solenoid again and the car started right up... again. Bad starter contacts right? Sure.
Since the starter on the 02 V6 Camry doesn't have removable solenoid contacts, I went and bought a new solenoid (out of my pocket). I pulled the starter out, replaced the solenoid, re-installed and.... same symptoms, but tapping a new solenoid won't work...
Now I was so sure this was going to be the fix, that when I returned I only brought the tools I needed for the install... Frustrating. I did have an old meter in my truck that I used to measure voltage at the solenoid..
I read 8.5Volts to the solenoid coil with the key turned to START. I hooked up a jumper battery as well, and yes, 8.5v is what I read.... Now the meters batteries are weak, the readings it gives me are inaccurate, and I'll be going back Saturday with my good meter, more tools, and wiring diagrams etc.
Are there any common issues with this vehicle I could look for here that might cause low voltage in the solenoid's circuit; ignition switch, specific splice point, area where wires get chaffed or pins come loose in connectors etc?
View 6 Replies
So i got a 2002 gti 1.8t awp . Wont start unless I crank it about 2-4 times. Also noticed a bit of a grinding/high pitched noise when cranking. when the car starts up it idles perfect, doesn't die , drives perfect etc...
Eventually i got the car scanned. & got 2 codes.
P0341 : Camshaft Position Sensor A Circuit Range/ Performance B1
&
P0230 : Fuel Pump Primary Circuit Malfunction
So I went and bought a Fuel pump , Camshaft position sensor & Even a new starter. Nothing fixed it. & the problem still occurs..
Heres a video of me trying to crank it ; [URL] .....
View 14 Replies
2002 Jetta GLS 1.8T (engine stock except diverter valve) 171k miles
It's done this a couple times now. Both while raining out/high humidity. Prior to this, I could hear the pump "growling". Sounded like maybe starting to go. You could hear it prime when opening the door or turning the key forward but would stay sounding like that even when the car was started. Without the radio, you can hear the pump running.
1st time- The car will crank without issue but never start. I let it sit a few minutes, turned key, heard it prime,tried again, started right up like there wasn't an issue and I couldn't hear the pump this time while the car was running.
2nd time-The car will crank without issue but never start. I let it sit for an hour, opened door (couldn't hear prime), checked fuse 28 (good). Figured wth, let's try anyways. Turned key, couldn't hear prime, started right up. WTF. cold idle normal (1000-1200rpm), light revs to 3000 ish normal. Turned off car, let sit for a minute. Turned key, heard prime, car started without issue and I couldn't hear the pump again while the car was running.
My dad is thinking to replace the pump right away. Is there anything else to try? The relay is working... at least sorta. With the somewhat intermittent issue, where to start? Either way, relay or pump, I will be replacing fuel filter.
View 3 Replies
The problem started several months ago. At first it would only happen once in a while and would only last about 5 mins. The first time it happened I had it towed to my shop and it ran fine when it got there. Go figure. They told me they couldn't diagnose it if it wasn't acting up while they had it. Makes sense. But it never does it when I'm there for routine maintenance. Now it's doing it for twenty minutes at a crack. It's usually fine around town unless I get stuck in stop and go traffic. When it usually acts up is when I get on the road between work and home.
Every time I stop for gas I have to wait for it to decide it wants to start again. All of this is putting heavy wear on my starter. I changed the oxygen sensor (position no. 01), because that was the only error code that showed up. That didn't fix it. My mechanic says he thinks the next best step might be the cam and/or crank sensor. If not that, then he thinks we should change out the brain. Somebody else said it might be the fuel pump goin out. because I travel too far for work and I can't afford to fix things that probably won't solve the problem.
View 1 Replies
I've been working on this explorer for a week now and I figured it's time to ask around. My explorer won't start/crank, I've replaced the starter, battery terminals, tested voltages/amps/relays and fuses, still nothing. All i get is a heavy clunk, like the starter is engaging but the flexplate won't budge. It's a 2002 4.0 xlt automatic.
I'm fearing the engine is seized as I've tried manually turning the engine with a socket on the crank pulley bolt and even with a breaker bar I can't get it to move. The thing ran fine a week ago and I can't imagine this thing would seize at barely over 100k miles, not hydrolocked or anything I can think of, are these engines prone for spontaneous seizure or am I missing something?
View 14 Replies
I have a 2002 2.0L 5spd Jetta that has an intermittent crank no start issue. The car has about 140k miles on it. The car will crank, but will not always start. It seems to start about 8/10 times. During the cranking, there is a rough noise coming from the starter area. More on this noise later.
When the car starts, no codes are thrown. When it refuses to start, the following codes show up:
P0261 Cylinder I Injector Circuit Low
P0267 Cylinder 2 Injector Circuit Low
P0270 Cylinder 3 Injector Circuit Low
P0264 Cylinder 4 Injector Circuit Low
P0445 Evaporative Emission Control System Purge Control Valve Circuit Shorted
P0037 HO2S Heater Control Circuit Low B1S2
P0418 Secondary Air Injection System Relay "A" Circuit Malfunction
P0420 Catalyst System Efficiency Below Threshold (I don't think this is related to the intermittent starting issues)
I've read up on these codes, and there are instances of other people getting these codes as well, but unfortunately, I haven't found any "smoking gun" that's the root cause to solve the issue. What I've tried, chronological order; none of these solved the problem:
Checking for spark. The spark plugs are new (within 2 months), but I removed spark plug and checked for spark.
Check fuel system: I removed the fuel line to the engine and drained it to a jug. I saw fuel flow intermittently when I keyed on the car. (Should it flow continuously?)Replaced the fuel filterSwapped fuel relay 409Checked wires near relays for obvious signs of damage (admittedly maybe I missed something here)Swapped coil pack. The coil pack was replaced in April, but I put a different one on, to no avail.
The spark plug wires were replaced at the same time as the coil pack.Starter
Thought fixing the noise might fix the starting issue. The noise from the starter is a grinding noise that occurs during the cranking process (not after, as is a common problem with these Jettas. It's NOT this noise: [URL] .... In any case, I tried the fix for the above noise by removing the starter and regreasing the inside. That didn't work and the noise and the intermittent starting issues are still here.Finally took the starter to Advance Auto Parts, had it tested, and was told it was good.
I think I have two issues that may or may not be related- the intermittent starting issues and the noise issue. They started happening at close to the same time.
View 1 Replies
Will try to sum it up: Most of the time, the thing starts like a charm, first try. Every now and then, though, I'll turn the key and either a) nothing will happen or b) it will slowly crank and eventually start. If nothing happens, I have always been able to try again seconds later and everything works OK. Have been through several batteries. Current battery checks out OK, as does starter and alternator.
A short circuit, perhaps? If so, how would I check it out? Problem with taking it to a mechanic is, most of the time all is OK. No pattern as to when the trouble will occur (has yet to happen with vehicle in the shop, of course).
View 1 Replies
So my 2002 ford explorer with the 4.0 L V6, has been cranking along time before it starts. I thought i had this figured out already, i put a brand new fuel pump in it from the ford dealer. That seemed to work, but the problem came back.
Especially when it is cold, it cranks a lot longer than normal to start. and when it does start RMPS go way up briefly and come back down. Seems to only act up when its cold out, say 35 degrees and lower.
So the remote start wont work because it only cranks for a few seconds and then stops. it tries this three times and it gives up. i go out there to start it and cranks for 10 seconds it seems like, sometimes i have to feather the fuel pedal.
View 7 Replies
I have a 2002 F150 5.4L (VIN-L) that has been sitting in the driveway since February. I have been a mechanic for 30 years for large commercial trucks, and my own truck has me stumped. I'm sure I've forgotten something but I'll try to list everything I have tried so far. It started with crank no start, no check engine light, checked for trouble codes got a trouble code for the CHT(cylinder head temperature) sensor.
- Replaced the CHT sensor. Cleared codes.
- Dash lights up fine, shows mileage, and anti-theft is not flashing while cranking.
- Fuel Pump does not seem make any sounds. Hit the tank with a hammer. Nothing.
- A little fuel comes out of the schrader valve on the fuel rail when I push on it. I have not checked it with a pressure gauge.
- Attempted to start with ether, nothing, so I'm assuming no spark.
- Fuel pump inertia switch isn't triggered.
- Checked several ground connections to the frame and checked ground connections in the PCM harness. All have less than 5 ohm resistance.
- Unplugged and plugged back in cam shaft sensor.
- Checked voltage on the TPS(throttle position sensor) I'm unsure about the results, if the TPS was bad wouldn't it just idle funny and/or stall?
Fuel Pump and PCM relays in the underhood fuse block appear to be good. All other fuses and relays appear to be good. I have been swapping the relays with one I think is good, although. Searched all over for additional relays, and found 3 inside the cab behind the passenger air-bag. Can't seem to find anything in the Haynes/Chilton manual that lists what they do. They are about half the size of the fuel pump relay.
Manually grounded the fuel pump relay, relay clicks but I don't hear a buzz from the fuel pump. Id like to run 12V to the fuel pump directly to see if that's my issue, but I'm not sure where to connect it without frying something important.
I bought the alldata.com DIY guide for my truck and it hasn't worked much. I have read extensively about others with similar problems and I just don't know what to do next. My main question here is, if the fuel pump is bad, would that stop the spark plugs from working? I'd rather not replace the fuel pump without being absolutely sure.
View 3 Replies
Having some problems with my truck.... First off I bought a 2002 excursion and drove it for one day. Then I was at the car wash cleaning up the truck. Then I saw the window fogging up so I turned the car off. Now it won't start.
I had previously installed a new stereo, but had some problems, so I ran the remote wire to the fuse box, because the wire in the harness wasn't getting power.. So after a little trouble shooting we found out that the fuel pump wasn't working or was bad.
We replaced it, now it has pressure but will not start, will start with starting fluid but will not crank on its own. someone told me it may be a bad PCM? and a dealer can only replace it... I don't have tons of cash, as i bought this truck on 8/30/12 and this happened the day after i bought it.
The previous owner has paid or the fuel pump replacing but I don't think its right on my part to have him pay more money as this may be a mess up on my part with hooking the radio up to the fuse box... we have tried the fuses,realys, crank sensors...
View 6 Replies
I've got a 2002 Ford Sports Trac that won't start ! It will crank till battery dies but is not getting fuel. I have had it towed 4 times in the past year. of the 4 times,this last time it wont start. Every time that I have had it towed back to my house and dropped in the driveway it has started up with no problems. It will run for a few months or more.This last time it would not.
Could this be an electrical problem.Maybe loose ground somewhere or something else. Would like to rule out some things before investing in a fuel filter or fuel pump. Would hate to buy new FuelPump and that not be the problem. Can't find free wiring diaghrams for this issue.
View 3 Replies
