S-10 :: 2001 4 Wheel Drive Won't Engage
Mar 2, 2015
I have an 01 s10 with the 3 switch 4x4. When I switch into 4hi I hear the click at the dash and I hear the switch on the transfer case but it doesn't engage in 4x4. The lights o. The dash act normal and says its in 4 wheel. I've had problems with the switch on the front of the transfer case in the past and was able to clean it and it was OK for awhile and now nothing. I replaced that switch and hear it working but still not engaging. I did notice a bad vac line on the firewall but not sure where it goes yet. Is there an order I should be checking components? What should I look for next? Also should mention in 2hi I get a whining noise like a shaft is spinning but when in 4hi the noise goes away and it drives like its in 2hi.
View 1 Replies
Advertisement
on a 93' 4 runner that will not engage 4 wheel drive. The 4 wheel manual shifter works fine, and the linkage underneath looks fine; however, the indicator does not light up - and it definately only has rear wheel drive.
View 5 Replies
After I push the switch for the 4 wheel drive, the light on the dash blinks but the front differential won't lock in even after driving around the block.
View 14 Replies
I bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 Replies
Its a automatic transmission with a v6 4.3 vortec. The front axle will not engage, it is not the acuator (I replaced it and the cable) you can pull the cable and the axle will engage. There is a low buzzing noise(coming from the drivers side) until you give it gas. This noise stops when the front axle is engaged. The transfer case will go from hi to low without any problems.
View 1 Replies
I have a 2007 Santa Fe crdi automaticl. When I push the 4 wheel drive button, the light in the dash goes on but the axels do not lock up. There is no code number that show up. Is this a sensor problem or what?
View 1 Replies
I have a 1998 F-150 and when shifting into 4 wheel drive (manual floor mount shifter) the drive shaft from the transfer case turns but the wheels do not engage.
Looking for a diagram of how the axle works?
View 3 Replies
So my Push Button 4 wheel drive wont engage. The light on the dash wont light up and it doesn't shift into 4x4. Where to start? I would like to check the simple stuff first. O and my heat only gets hot when im giving the vehicle gas. This is all on a 2003 Ford Explorer.
View 2 Replies
I have just switched from GM to Ford and have a new F250 4x4 XLT. I am wondering how to engage 4 wheel drive correctly. I have the manual shifter and the manual lock hubs. However during my test drive I shifted the lever into 4H and 4L and it seemed to engage just fine. Do I need to lock my hubs as well? Or if im just in a wet spot can i just shift into 4h without locking my hubs? I know if I am in anything serious I need to lock the hubs. I just want to be sure before I get into a tricky situation. My 02 GM all i had to do was push a button and it shifted automatically.
View 7 Replies
I have a 2001 f250 7.3 powerstroke it is an automatic. It has the switch on the dash to engage the 4 wheel drive. When I turn the switch nothing happens.. no lights come on or anything. it has warren locking hubs. What my problem is???
View 2 Replies
I recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
View 2 Replies
Do a 2004 Saturn view front wheel drive transmission will fit in place of an all wheel drive...
View 1 Replies
2001 7.3 l 4X4. I have done a ton of work to get the suspension and steering right. Changed all the shocks, added hellwig sways to front and rear, replaced steering gear with redhead, ball joints and added warns hubs. My question is today was the first time engaging the four wheel drive. I locked the hubs and turned the switch to 4X4 low, it starting squeaking and squalling and felt like my wheels were coming off. I put everything back to 2WD. I switched it to four wheel with out locking the hubs. no problem. When I locked the hubs in it started again. Been doing some research and looking at needle bearings, wheel bearings and axle joints.
View 10 Replies
2004 Santa Fe, after starting car the brakes make a grinding noise, the nthe ABS, ESC and 4 wheel drive light come on. After the initial grinding the noise stops and the brakes work fine. Just the lights stay on.
View 4 Replies
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 Replies
Every time you engage the car in drive it blows a fuse. I have checked through the wiring but cannot see what the cause is.
View 14 Replies
Overhaul trans, new old pump, but doesn't engage in drive. Reverse and all three low work fine. Drive will only work when rpm's are applied. But without any power.
View 4 Replies
My wife and I have a R and a rabbit, she drives the R mostly and i drive the rabbit mostly..... I drive further to work, anyhow the past week she told me that the clutches feel like they are slipping and when she puts it into drive sometimes it wont engage... or when she puts it in p it says in d...... anyhow off to the dealer it goes for who knows what and how long... and the car is stock....
View 24 Replies
We recently had an issue with our 2011 GX460. My wife first experienced the transmission not wanting to engage after being put in drive. Once it did engage there was a loud bang/pop noise, then no issues afterwards. The same thing happened to me this weekend. It was weird, like the brakes had frozen up then suddenly released and the transmission slammed into gear. We bought the vehicle used a couple months ago with 39k miles. With factory warranty remaining it will be heading to the dealer shortly.
View 14 Replies
My Auto 2.4 850 SE (38600miles) does this lately:
- idles at about 1200 rpm, and takes long to settle to its 850 position, even when warm;
- when I engage Drive, idle drops to very low, car vibrates as if engine wants to switch off, then rises again as I give gas and pull away.
Why this is the case, and what I could do to remedy this? (About 2 months ago, idling was going really nuts! I removed the flame trap and fresh air hose: it was full of oily gunk and I gave all components a good clean up with carb cleaner and then replaced them, and then idling all fine after that).
View 11 Replies
My 1994 Chevy Suburban will not engage the front drive shaft. It has an electric actuator and it will not engage. the transfer case engages but not the front axal. When I shift the transfer case into 4Hi or 4Low it will shift itself but the light will not turn on. I have heared rumors that you might have to manualy connect it to the battery and have a kill switch in the cab. What is the problem and should I connect it manualy?
View 6 Replies
