S-10 :: 1999 Chevy Transmission Downshifting At Highway Speeds When Slightly Let Up On Throttle
Feb 18, 2014
My S10 started downshifting at highway speeds when I slightly let up on the throttle. It only starts after driving 20 or 30 miles down the road. (gets hot?) It also hesitates slightly starting from a dead stop as well after that. I dropped the pan, cleaned it up and added new fluid. There was a fine powdery sludge on the magnet in the pan, but no metal shavings. It is still doing the same thing.
It has 95,500 miles on it. 2.2 motor. The fluid was low a couple weeks ago. I added a bottle of conditioner. Don't remember the brand name. 2 reservoirs in the bottle so it mixes as you pour it in. It started acting up 7 days ago.
View 1 Replies
Advertisement
Have a 2008 Elantra GLS with 63K miles. A/T was serviced by dealer at 51K. Car now occasionally downshifts from 4th to 3rd when driving between 60 and 70 mph. Happens only when trans is hot (after 2-3 hours on hiway). When it occurs, it searches for the right gear, going back and forth from 3rd to 4th for several minutes before returning to normal. One thing odd is if I shut the car off for 5 minutes after it occurs, it runs fine afterwards. Do I need an ECU update or do I have a A/T problem?
View 11 Replies
I have a strange noise that occurs at both highway and surface street speeds. On surface streets at low speeds 45 mph and under, if I let off accelerator to coast and lightly step on accelerator I get this quick sharp noise.
Everything I have read regarding a similar noise is under load and being described as a turbo fart. Clearly I am not under any load. I'm lost.
Definitely not a low woooo noise. Also not a hard accel and release and definitely no chuckle and or popping. The sound is high pitched and quick, roughly .5 to 1 second at most. The sound is more like a "zzzrrp" or "zzzoop". I can replicate the sound 50% of the time easily at speeds under 45 mph by briefly coasting (no accelerator) and lightly tapping the accelerator and releasing or holding. Occasionally this sound will occur at full stop when I step off of the brake pedal and before I step on the accelerator. This sound can also occasionally be heard at highway speeds under similar accelerator conditions though it may be more frequent and I just don't notice it.
Would this condition throw a code? Just received "Total Ford Scan Tool Package Enhanced Bundle SP03" scanner from autoengenuity. Hoping to put it through its paces tomorrow.
Additional info: 145k miles. Injectors serviced by a reputable diesel shop here in Vegas approximately 1.5 years ago. Unknown oil leak where oil is collecting in the valley on top of the engine beneath the turbo. HPOP seals were replaced roughly 1 year ago at another reputable diesel shop here in Vegas. Still have an oil leak (turbo related?) Oil is under 500 miles old and acceptable level. Fuel filter is due for a change but that does not seem to affect condition. Air filter 1000 miles. Thinking about upgrading to AIS severe duty kit soon.
View 14 Replies
Noticed the steering wheel shakes just slightly at highway speeds. Happens to me when I'm at around 65-70mph and above. It's just very slight, so I really wasn't thinking its an alignment issue at all. I didn't know if this was a bit normal for these B7s or what. I've had alignment issues in cars before and this just doesn't feel that bad, but its enough to give me pause.
View 7 Replies
Took car in for normal service (69,000 miles) and had Tranny Fluid Service completed. When I took the car home I noticed some slight tranny slipping while accelerating up to highway speeds (so assuming 4th to 5th gear, maybe 5th to 6th). Took it back to the dealer and after a week it had a new transmission. Took it home and it slipped again, also only accelerating to highway speeds. Took it back and they told me they reset the computer that monitors my driving patterns. OK, not exactly sure what that means. So, now driving to work this morning it slipped (or maybe hesitated is a better word) again when accelerating from about 55 mph to 60 or so. Car has never had issues like this before, gas mileage is still in the 30 mpg range.
View 9 Replies
Got a strange one here. 1995 Buick Park Avenue, supercharged 3800, 159K miles... an older car, but an unmolested one. A little over a week ago I began to notice an occasional miss when cruising along at highway speeds, along with a slightly rougher idle. Both the fuel filter and the plugs/wires predated my ownership of the car (a little more than 6 months); so seeing no obvious culprit, I replaced them and hoped for improvement.
Unfortunately, neither had any impact. The missing continued to become more noticeable. It was never present under acceleration. Most of it was like a split-second long version of "bucking" that could be observed while cruising at lower (<2000) RPMs. It was also very noticeable at idle. Eventually a code was set: P0341, camshaft sensor issue. If the story had ended there, it would have been just another night in the garage. But it didn't.
As I was noticing the aforementioned symptom increase, I also noticed my voltmeter would occasionally "twitch" in the downward direction. Eventually I had an incident where I came to a stoplight... transmission in Drive, foot on brake, gauge dropped to around 10-11v. It returned to 14v momentarily, but dropped back down, held there for several seconds, returned, etc. No particular rhyme or rhythm. Of course my first guess was that the alternator was failing; a separate problem from the other.
I checked all the relevant connections (at the battery, at the alternator, etc), and cleaned them for good measure. All were tight, relatively clean, and the cables showed no resistance on the ohmmeter. It happened that I had another correct alternator on hand (used/working pull), so I swapped it in. No change. I reinstalled the original and was back where I started.
On my most recent drive, I noticed both issues had become very noticeable. The drop in voltage was happening at nearly every stop, and the missing was happening a few times per minute while coasting along. There seemed to be some correlation between the missing and voltage fluctuating, but it wasn't absolute.
I decided to attack the voltage issue again. Re-checked all the cables; same result as before (all OK). Looked all over the car for possible bad grounds, loose connections, or other visible problems, but found none. My next thought was to run a jumper from B+ to the voltage regulator's Sense input (have seen issues there on more than a few older vehicles) - but after reading that this car uses the PCM as the voltage regulator, I didn't proceed.
Just to be certain I'm going to have the alternator tested by the local auto parts store. But I suspect it'll pass.
View 8 Replies
for the last several weeks, I've noticed a problem that seems to be getting progressively worse... there is a vibration seemingly from the front end (possibly passenger side), and it only appears on the interstate at typical highway speeds (70-75 MPH). facts:
1. It does not happen below ~70 mph.
2. It doesn't appear to be a wheel bearing - no noticeable change in tone or "amplitude" while turning at speed.
3. I use cruise control all the time on the highway, and it is more noticeable going downhill (increases in vibration), when the engine is obviously off-throttle.
4. The car is a 99 V6 5mt.
5. The axles that are presently on the car are Raxles, and have been on it for ~4 1/2 to 5 years.
6. I recently changed over (this past weekend) to my winter/stock wheels and tires, but it was doing it with the summer wheels and tires.
7. It happens regardless if the gears are engaged or not (5th or neutral - I coasted down a hill on the interstate today in neutral to add more info).
8. I've replaced the wheel bearing on the passenger side about 6 weeks ago.
I'm thinking I have an inner CV Joint that is starting to fail. The boots are intact, as I inspected them recently while replacing the clutch/pressure plate/throwout bearing/flywheel. The transmission axle flanges had no play. The vibration was occuring prior to when I changed out the clutch.
Thoughts? Inner CV joint, or...???
View 4 Replies
I have a 2004 F150 XLT SCAB 5.4L 3v Fuel that I drive Daily, it has 280,000 miles on it. While driving to work (70mph) my throttle became unresponsive and it felt like the transmission was downshifting. Made my way to the edge of the highway and placed truck into Neutral, then the engine quit. Tried restarting at which point would not fire. After letting the truck sit (while waiting for a tow) I decided to try to start it. The Truck did start and ran for only about 2 minutes and then quit. The Tow truck finally arrived and I tried to start again with the same problem occurring, stated and ran for about 2 minutes (no throttle response) and died.
Got the truck home and decided to remove the Fuel line from the filter to see if there was fuel flowing, which there was none and no pressure. Replaced the FPDM with a new one, old unit was corroded but not cracked (replaced it once before). Tried to start and would only crank with out any fuel flowing (still had it removed from the filter). Thinking it may be the Fuel Pump but have to drain the tank being that I just filled it this morning before it died. The problem is, how to drain the tank before lowering it if the Fuel Pump is not running??? What the Problem is or how to test Fuel Pump or drain the Tank?
View 2 Replies
My 2006 expedition surges very slightly while cruising under very low throttle. Usually most noticeable at 60-65 mph with no headwind.
Took it in and had my mechanic check it out. He confirmed the slight surge and said it felt like the torque converter was locking and unlocking. No codes or pending codes were found related to the power train.
Abs light is on for a bad rear wheel speed sensor. Code for right rear. Checking the sensor showed 3 ohms for right, 5 ohms left ( left is less than a year old on a new wheel bearing.)
Initial thought was the bad sensor is giving bad input confusing the pcm/tcm. But the condition remains with the sensor unplugged.
Driving down the road watching the tach, it does appear that the converter is not staying locked. Condition goes away with more throttle. Motor runs smoothly otherwise with no indications of misfire. Plugs have 50k miles on them, as does the transmission fluid. Fluid is red and smells fine. Never gotten hotter than 210 by the gauge in the pressure port.
Why would it lock/unlock at very low throttle, but lock tight with more throttle? Tps flaking out? Throttle body motor getting twitchy? Can I pull my popup to the hills this weekend?
View 3 Replies
I have a '99 Silverado 1500 with a 4.3L V-6 amd 188,000. It picked up a problem recently that's been stumping me. Occassionally, and for no reason I can sort out, it starts to shimmy badly. This behavior has come about at several speeds. Sometimes just cruising down the road at 35-45 it starts to shimmy and wobble and the steering wheel shakes as if a wheel is horribly out of balance. Other times this occurs at highway speeds - it's noticeable and alarming. The problem can last a long while; othertimes the symptoms disappear in a few seconds. The first time it happened I thought I had a flat or was about to lose a wheel - this is not a subtle problem.
I've checked several things and came up empty. No delamination in the tires and nothing out of round, but just to be sure I had the wheels balanced and rotated - the balance was spot on when checked. Alignment is good. Did those things, but the symptoms continued. The vehicle is high mileage so I put in on the lift and checked the front-end. The steering rack has a very slight amount of play and the hub bearings have a very small amount of play too - I'll get after those, but they're not causing this intermittent problem. Everything else is tight. Shocks are fine, brakes are fine, I checked the rear-end as well - everything is straight and true. Air pressure is set correctly. I checked the driveshaft for runout and play - that's not the problem. The truck has never been in an accident and nothing seems misaligned.
The truck drives like a new truck most of the time, then suddenly, on a smooth road, it starts wobbling around. I'm starting to believe the problem might lie under the hood. I had a problem some time back with misfiring and the truck bucking - this turned out to be a worn distributor. A new distributor, rotor and wiring solved that problem. But these symptoms are not similar - this is not a bucking problem; the entire vehicle starts to shimmy and wobble with the steering wheel vibrating back and forth. It's hard to tell, but I cannot detect any misfiring or rough running in the engine when these symptoms appear and I have no 'check engine' warnings.
Are there any engine/transmission/drivetrain related issues that could cause intermittent symptoms that feel like an out of balance condition? A few other facts:- I have noticed the truck is a little down on power lately- The fuel economy has dropped off - I used to do around 20, now I'm down to 16mph highway- (Very) slightly rough idle
View 5 Replies
I have a 2004 Ford Escape XLT, auto,V-6, with 129000 miles on it. It runs fine except for a couple of things. One is, at highway speeds the transmission will seem to shift up and down. Also sometimes at highway speeds I get what I describe as a "bump" or "shudder" I think it is coming from the transmission.
View 4 Replies
I have a 2014 screw 4x4 v8 that has been in the shop 5 times now for something that the dealership can't duplicate, and that is intermittent enough for me that I can't determine what the conditions need to be in order to duplicate it myself.
My transmission will shift hard under two different situations:
1) when rolling through a stop, or a momentary stop at a stop sign, the transmission holds up between 3 and 1, and when I bring the rpms up, the transmission shifts down into 1, making a hard clunk;
2) at highway speeds, more so when using cruise, if I accelerate and the truck shifts down from 6 to 4, there will be a hard shift as well. In fact, when I'm on a long stretch of flat, open road using cruise at 70-75, I can feel a slight bump through the steering wheel and floorboard, as if the cruise is trying to engage the throttle a bit more, but only for a split second. But that will happen quite a few times within a couple miles until I come up on a grade and the throttle has to engage for a bit longer to keep speed. Sometimes, the hard shift will do occur going to 5 as well, but 90% of the time it will be a 6-4 shift. If the truck decides to shift from 6-3, there's no issue and it shifts and accelerates like it should.
Again, this is so intermittent, but when it happens, it happens several times. I've had the service tech ride in the truck with me, all the while not being able to duplicate the issue. I understand that these are learning transmissions, so the only thing I can think of is when I try to duplicate it by accelerating over and over, that the transmission adjusts the shift pattern or fluid pressure to compensate.
View 14 Replies
Is this behavior normal: I test drove a 2010 corolla LE with 4-spd auto, 41K miles. Noticed that on level highway 60 mph that whenever I eased up on the gas that the RPMs would shoot down. Vehicle speed was barely decelerating since I was on level. As soon as gas reapplied (gently), then the RPMs would shoot up. I'm guessing the delta was like 300 RPM. I get the impression that at highway speeds the car is mostly in 3rd gear or shifting up and down a lot. I've read a lot about a TSB for 2011 corollas but nothing for 2010. And I think that problem is different. So my question is whether this is "normal" for driving at highway speeds?
View 5 Replies
I have a 2001 chevy metro 4 cyl. with 13 inch wheels and automatic transmission. The engine rpm's are running high at highway speeds. Would a larger diameter wheel support this situation?
View 8 Replies
I recently overhauled a 5r110w torqshift in an 03 F350. The trans is acctually an 06 trans. The original problem was that the truck was "tieing up" on take off. When i tore the trans down i found the Low/Reverse clutches were burned bad and welded together. Everything else looked decent. I replaced all the clutches and checked all the clearances, except the OD clutch because i could not find any specs, or a way to adjust it. The trans has been doing good for around 200 miles. Now it has an intermittent problem.
When you first start the truck its like the converter has to fill up. It has a delayed engagement, but only AFTER you shut the truck off. Also, after driving about 10 miles, sometimes it will feel sluggish. I put my Solus Pro on it and while watching the trans data noticed that the transmission is not downshifting all the way int first gear at times. It will down shift, and then try to take off in 3rd and sometimes 5th gear. I was looking thru my ATSG manual and i can see which clutches turn in for 3rd. It seems like a solenoid is sticking on and allowing fluid to "leak" and keep the wrong clutch turned at the wrong time.
View 12 Replies
Ok so this is something I can't quite wrap my head around. I have a 1999 K1500 Suburban, 5.7L. I have only owned it a few months. The thing is, shortly after I got the truck, we took it out of town, where it died after a little over an hour of driving at highway speeds. I had punched the odometer to watch the gas mileage, and we had run it about 70 miles when it died. We got it to our friend's house, where we were headed anyway, and stayed over, planning to look at it in the morning because it was later than part stores stay open in our rural area. Thing is, in the morning it fired right up. So we headed home, and once again, after about another 70 miles, it shut down and refused to crank.
This time it happened as we were coming back into town, and on a hunch I said that something must be overheating for the problem not to be present until after an hour of road time. So we pushed it a safe distance off the road, and went and grabbed something to eat. After about an hour we made it back to the truck and success! It cranked back up and we made it the rest of the way home. Since I have driven it to town and back, and to my parents a few times, but never more than thirty or forty miles away. It never hesitates to crank, and sounds ok running. Although I will say, I have not owned a truck before or a V8, but it seems to not have the power it should (my thunderbird with a 3.8L had more punch), and I did noticed both times this happened that that problem seemed more pronounced right before it died. But I don't know if I just feel that way just because I am used to driving cars, and the truck is heavier. When it dies, you hear the starter relay click, and that's it.
View 9 Replies
I've tagged this as a Civic but it's a 1999 Honda City 1.5 EX. (Asian market vehicle)
Normally this car would shift to 2nd at 20km/hr and 3rd at 40. But if I hit 40+ and it shifts into third, then coast for a while and let the speed drop to below 40 (say 35), when I push the throttle now the car doesn't kick down and it feels like it has almost no power even if I push the throttle to the floor. The feeling of no power lasts for about 2 or 3 seconds, and then the car downshifts automatically and the RPMs shoot up. Quite dangerous trying to move around quickly in Asian city traffic. I adjusted the kick down cable to make it stiffer, but now the same problem happens at a higher speed and shifting at a higher RPM.
View 1 Replies
When my TREG is downshifting from 3rd to 2nd gear, it sometimes blips the throttle just a bit before settling into 2nd. Almost like one would do when down shifting a manual transmission.
View 3 Replies
I have a '99 Chevy 2500 diesel truck. After driving it at highway speeds for more than 20 minutes and turning it off, it won't restart. The problem seems to be in the battery cable and is definitely heat-related. In cold weather or after a fairly short drive, all it takes is popping the hood to cool off the engine compartment, and waiting. If the engine and/or the weather is too hot, that can take an hour. Then it starts just fine. I've cleaned the terminals and made sure the connections are tight. Two mechanics have looked at it and were stumped.
View 1 Replies
Just bought this car and when I am on the highway I let off the gas and it automatically downshifts. no engine light or anything. and when I press the gas again it returns to the proper gear.
View 3 Replies
The other day I pulled into the parking lot put it in park and let it idle for a couple minutes, it stumbled and when I started driving off it was missing. I pulled the valve covers off and check the connection.. I drove it home and it had a bad misfire at 1500 RPMs. The truck shook violently at that RPM but when I got it up over 2000 smooths out..
View 1 Replies
