I have a 1999 chevy s10 2.2 L that just shut down while driving, I have replaced crank shaft sensor, ecm, ignition control module, coil packs and still having issues, she will start now but won't stay running, what else it could be, it has been down for almost 5 months.
View 1 Repliesi have a 2005 chevy malibu classic. a few months ago it started sputtering when we would try to crank it and would take several tries before it would run, then it stopped. So far we have replaced the fuel filter, fuel pump, fuel pressure regulator, idle air control valve and crankshaft sensor, and it still wont stay running when you try to give it the gas, it dies....
View 4 RepliesMy truck is an 02 F250 7.3 with 280,000+ miles on it, so I wouldn't be surprised if I might have a number of things going wrong. It runs pretty good, but is still far from 100%, at least up to my standards. So the problem has been going on for the last two or three weeks and got worse today, and there were a few things leading up to it as well. I'll start off with the first thing that happened that I think might be related. It was about 6 months ago, my buddy and I were putting my new headlights in.
It was parked in his garage and we backed it out a little bit to try and adjust them. It was sitting there idling for a minute or two and just shut off or almost stalled out. Tried to restart it and it wouldn't start, tried multiple times to no avail. It acted similar to when I had glow plug troubles when I first got the truck, it would just crank and crank, but never actually kick over and start, along with putting white smoke out the exhaust. Ended up waiting about a half hour and then the truck fired right up with no problems after that, so I didn't think much of it.
Then fast forward to last week to when something similar happened. Started it up after sitting for a few days, started right up, idled for a few seconds and then just shut off. Started it back up ran for a second and died again. Tried a third time with the same result. Fourth time fired right up again and stayed running, let it run for a few minutes and was fine. Also along with this, there was a bad squeaking coming from the front of the truck, like what a belt would sound like. I have recently replaced the belt because it was squeaking and actually got chewed up and almost shredded completely apart.
So not sure why it is squeaking again, but not sure if this could be related or not. Then took it back to my dorm room to get my stuff, and then made it the hour or so drive home from school, without issue. Even went to a few stores before I went home, and shut the truck off and started it back up multiple times, again with no issues. When I drove back earlier this week it was fine until I got there and put it in park. It idled for few seconds and then cut out for a second, but then idled back up and continued to run fine. It has done that a few times as well. So it will do it on a cold start or after already fully warmed up.
Then it got worse today. Again had trouble starting it cold, same as what I explained early. Except second time cranking it wouldn't start at all, then on the third crank it started up and stayed running. But on the drive home is when it got worse. About 5 or 10 minutes into my drive, was just cruising doing at about 45 or 50, and truck just shut off, died/stalled out. It cut out and shut off for a second or two and then started itself back up and continued on like nothing happened. It scared the crap out of me the first time it happened, I was waiting for something like that to happen, but still wasn't quite ready for it.
The truck acted just like it would before you start it, with the key on, dash lights worked and the radio still worked. It did this 4 more times in similar ways, would die and then start back up, at various speeds and at roughly 5 or so minute intervals. I decided to just keep going as long as the truck would start and stay running, hoping to make it home. It did it a fifth time and this time the truck completely shut off and wouldn't restart itself. It was hard to see, as I was watching a few different things at one time, but I think it tried to restart, I noticed the tach bounce between 200-400 RPMS and then die. So I had to pull over and then restart it, fired up and drove fine. That was about half way home, and I made it the rest of the way home without any more problems.
So obviously I'm wondering what would be causing the truck to do this? I've done some reading and have a couple ideas, but not really for sure on anything. I was thinking maybe the CPS, I think it can cause a no start issue. Could ICP or the ICP sensor have something to do with it? I was also thinking maybe something fuel related, such as fuel pressure or a bad fuel pump. Any of those sound to be on the right track?
I have the torque pro app, but not exactly sure how to use it yet, and also just got access to my Uncle's Snap-on scanner, so I ran some tests and pulled some codes. How to more utilize these tools in diagnostics. I did get a few codes, but I'm not exactly sure how they might be related. The codes are pulled are:
P0470 Exhaust Pressure Sensor Circuit Fault. Just cleaned that out as well as the tube about a year ago, but I guess could be clogged again or has gone bad.
P1274 Cylinder 4 (E) High to Low Side Open. Did some reading and figured out that this could be UVCH related. At the same time, about a year ago, did new injector O-rings as well as all new Motorcraft UVCH's, so can't imagine that one is bad. Or that one could be loose, I would have guessed it would have happened more when I first did them, not a year later, but who knows.
Also pulled P1876 T-Case 2wd Solenoid Circuit Fault. Not sure if this is related at all, but also not sure what it means either. I read that it could be ESOF system related, which I do have, but I have manual lockout hubs, so maybe that's why it throws the code.
Also a few things that may or may not be related, but I think worth noting. Ever since I've had the truck the check engine light will pop on and off sometimes. It will do it on a cold start or, when I first start driving and its not fully warmed up yet. It does it most when the engine is still cold, and it almost never comes on once the truck is fully warmed up, but has came on and off more frequently lately. When driving, it will only stay on for a few seconds and more often when I'm lugging the engine or at lower rpms, and will commonly shut off if I let off the throttle.
I don't think it really comes on at higher rpms. I also have a slight oil leak in the valley of the engine, seems to maybe be coming from the front of the motor. Nothing too serious, leaves a small puddle where I park, loses enough to be at the add mark, a little before an oil change. Changed the oil about 1500 miles ago and have been able to notice a slight drop in oil level. Also I have changed the fuel filter in the last 500 miles.
So our battery died and after getting it jumped the Jeep would not stay running. As long as I was giving it gas it would stay running. As soon as I stopped giving it gas it would die.
View 4 Repliesi have a 1991 ford escort pony i w driving it fine all day then all a sudden i stopped to get water the car died when it did i tried to restart it , it bogged out and didnt start i waited a hr it started idled for 20 mins reved it up everything seemed ok but then i went to actually drive it i got 1/3 of a mile if that and it died on the side of the road with my lil daughter in the car and 104 degrees outside. me and my father thought it was a furl filter or pump but in the primer valvei t has plenty of fuel and pressure. what it could be?
View 1 RepliesI have a 89 Mercedes 190e. The car stays running and will drive but after so long starts acting like it's starving for fuel. I have spark and nothing wrong with fuel filter but when tested there was no pressure what's odd is the fuel pump was tested and it works fine all the lines have been cleared I'm stumped what else can I check...
View 13 Replies1992 Honda Civic Starts fine but kills as soon as you release the key. Hold the key in the position with the starter motor running and it keeps running. In the old days we would replace the resistor on the firewall. Today?
View 3 RepliesWhen its cold outside it starts and runs good for about a second and then shuts off or runs really rough and then takes off. I tried turning it off and starting it about 4 times. After the fourth time I gave it a little gas and it started after that. If the block heater is plugged in it starts fine. And starts great the rest of the day after the initial start. It is not that cold here, lower 20's in the morning. Where to start with this problem?
View 13 RepliesI recently replaced the transmission in my car. I put new oil pan gasket, valve cover gasket and plugs in it. Got everything back together and now it won't stay running. It starts but will not stay running . I pulled the plugs out to find they were the wring ones that a was sold So They gave me the correct ones. Still doing the same thing. I've checked every connection. All are plugged in all lines are hooked up.
View 4 RepliesI have my car and it takes a few times to start but once its on it wont stay running if i let go of the key or the ignition cylinder ....
View 4 RepliesI just bought a 1982 Chevy c10 305 small block.It had an oil leak so i began putting new valve cover gaskets, and then New Valve Covers(Edelbrock). Because the covers were taller, I had to remove the EGR valve and bend a new fuel line.There was a plate i installed inside the valve cover where the PVC goes into? is this a problem?I noticed the hose from the distributor rotor button(vacuum?) was not connected to anything.I plan on putting a EGR blocker plate, but was told it wasn't needed to run.
So now it starts up but will not stay running idle. Do i need an EGR blocker to run?IS that plate needed inside the Valve Cover?Does the hose from the Distributor rotor need to be connected?
So about 3 weeks ago, I was driving down the road at about 55 mph, on cruise control, when my car just started slowing down. I looked to see all of my dashboards lights on and I realized my car was not running. I shifted into neutral and the car started right up again, but when I pushed on the gas it just kind of stuttered and shuttered before dying again. When I came to a stop, again the car started right up, but repeated the shuttering and hesitating when I pushed on the gas and tried to get going again.
So, I repeated, but this time i just pushed very gently on the gas, getting up to between 5-10 mph before the car died again. At this point, it just stopped running completely. The engine would turn over, but would not keep running. When I got it into the shop, the mechanic said they put a fuel pressure gauge on there and the readings indicated that there was plenty of pressure, no problems the fuel pump or lines.
After further research, the mechanic said he thought it was an electrical problem, that it could be the crankshaft sensor or the ignition switch module, but he just did not really know for sure. I had him replace the crankshaft sensor, since it was the cheaper part, and it didn't fix the problem. So now I am just kind of stuck on what to do here.
1999 Chevy Blazer, 4.3L V6, 173,447 miles
Working on his 1999 Blazer that he just bought, it has an electrical problem.....the gauges are inop, and the engine wont shut down and the 4X4 wont engage unless the headlight switch is turned on and in some instances the high beams must be on. We have replaced the high beam multi switch, the headlight switch and the ignition module. We suspect that it might be a bad ground or the interior light module.
We just replaced the engine the other day but the problem existed prior to the motor swap.
I have a 2002 f250 SD v10 4x4. I had a ground wire break fixed that know noon of my instruments work. Dash lights up but nothing moves. Pulse my parking lights stay on when the truck is shut off or when I turn lights on then off. I have to disconnect the battery to get hem to shut off.
View 3 RepliesMT 2500 Where are you I've got a weird one. 99 Chevy 5.7 dully dump truck. The engine cuts out while driving at 3000rpms only. If you keep your foot in it it goes away at 3200. Does it in any gear(auto). Also, stopped and in park, it will do it at 4000rpms. Acts like a rev limiter. Fuel pressure does not change (60-62psi) when this happens, does it in open or closed loop. I disconnected the maf and no change. I've installed new cap, rotor, plugs, wires, coil, module(all original with 165K), no change. Runs sensational until 3K rpms.
View 14 RepliesAt first it wouldnt start without me burying the throttle, and wouldnt stay running if i took my foot off the gas, i replaced the throttle position sensor and it starts with no issue, but now if i give it any gas, it shuts of, unless i let off the gas very slowly, what do i do?
View 7 RepliesMy issue is not with the truck starting its with it staying running. I had plugged in all the night prior and all day while at work. When my shift was over went out started fine let it run for about 20 minutes and left to make my way home. During the trip it ran fine for about 1/2 a mile and then it started idling really rough at a stop light went to go threw the light and it as though I had left it out all night with plugging it in. I went to turn on a side street because this situation was not going to end well and it died trying to turn. It would not start back up I was able to get a jump and made another 1/4 of a mile and it died right in front of my house. I replaced both the batteries this morning and it fired right up lasted about a minute and then died again. All the gauge read fine, oil level is good, and the injectors were replaced 2 years ago.
View 14 Replies'99 K1500, 5.7L, 130K miles, regularly serviced and well maintained, no garage so sits out in weather. About 8 months ago we started to experience no starts after rains, engine would fire off, but not stay running, security light NEVER came on. Took to regular mechanic and had fuel pump replaced (needed it anyway), wiring "repaired" behind dash. No problems till last month, then same started again. Sometimes will start after 5-6 tries, other times will not start till 10-12 hours AFTER rain stops.
Security light came on ONCE while driving for 5 minutes, then went out. TSB's indicate possible corrosion in the Passlock sensor voltage, underhood or under body connections, may be reason. Where these are as I would prefer to check them myself to see if simple solution before pay mechanic to find the same. Since did not reoccur for a while after fuel pump replaced, are there connections that would have to be pulled to replace tank that may now be not sealing again with time? Any resource for wiring diagrams for Passlock path?
Got a 99 F450 7.3 with 190k miles, started acting sluggish. When cold, it wouldn't stay running, almost as if out of fuel. Would stall out when you pressed and released the accelerator but would idle fine. Now, it won't even stay running. Still acts like it's out of fuel. Changed the air filter, fuel filter, and added injector cleaner and conditioner. What else could it be? after warming up when shifting gears and letting off throttle it stalls and when restarted lets off blueish white smoke.
View 2 RepliesWhat's up power stroke fam. I have a 1999 F250 Super Duty 7.3 liter this is what happen, was leaving the job site the truck started just fine ran for about 3 city blocks stopped at a stop sign and it started to run ruff like it was out of fuel but had a half tank then poof it shut off. After towing the truck home and trying to start it I could hear a relay clicking very sporadic the service engine light came on then when off and the truck started and the exact same thing happened started running ruff and shut off. Where should I start other than taking it to the shop?
View 14 RepliesI Have a 2002 F 250 That I recently changed the fuel pump. and now I'm having a tail light problem. when i start the truck, my tail lights and plate lights comes on (dim). if i turn my head lights on the truck stalls out. if i step on the brake or put the truck in reverse it stalls out. if i put it in drive it runs just fine. i checked my fuses and relays and the problem is still there even when the relay and fuse for the lights are out. when i turn the truck off all the light go out.
can't seem to find any info on this problem anywhere.