S-10 :: 1993 Blazer Electric 4X4 Shift
Feb 12, 2012
I have a 93 S10 blazer that has electric 4X4 shift. The only way it will shift into 4X4 is to come to a complete stop put truck in neural and hit the 4X4 low then both lights flash then both lights remain lit then i can hit 4X4 high both light flash again I hear 4X4 module click and front axle engage but I'm not sure of its in 4X44 if I hit 4X4 hi again both lights flash again and I hear the clicks but when u go 2 drive its like its in super super low gear if u don't put truck in neutral and come to a complete stop no matter wat button hi or low u hit nothing will happen.
View 14 Replies
Advertisement
1993 Chevrolet S10 Blazer will not turn over the battery is fully charged when key is turned there is nothing not a sound only smoke coming from a wire on top of fender under hood.
View 2 Replies
I have a 93 Nissan 240sx that exhibits weird electrical behavior. I've had the battery and alternator checked at two local Advance Auto Parts locations with results indicating no problems. The car starts and drives fine. Immediately after start, my automatic seatbelts are engaged and the RPMs drop to about 400 and the car shakes violently (while pressing brakes and even when not pressing brakes). RPMs drop anytime accessories are in use. When braking at a stop light, the RPMs drop and the car shakes again. Using my headlights causes the RPMs to drop but not a point where I feel shaking. The problem is worst at night when I am pulling up to my apartment complex with lights on, braking, and using my power windows to access my gate card reader. I don't know if this problem is related, but when I am listening to the radio and turn the volume all the way up, the radio keeps cuts on and off. I have a suspicion it's the grounds, but before I start tracing all my wires. I'd like to hear everyone's input. I determined it was the brake booster vacuum because it also happens when not using the brakes and pinching the line has no effect on idle.
View 10 Replies
I seem to have a problem getting our 2002 Chevy Blazer to shift out of 4WD. We hardly ever use the 4wd, but quite a bit of snow today, so switched it on. Later in the day, it started to melt and we had dry pavement, so we tried to switch it back to the 2HI position.
After pressing the 2HI button, there were several clicks, sounding like it was coming from the glove compartment area, the 2HI light would flash for a couple seconds, then switch back to 4HI.
It is an automatic, I searched the manual and tried everything it suggested, I'm thinking maybe some type of relay, sensor or fuse is out?
View 6 Replies
I own a Elantra 2011 and I have a major problem. I cannot shift from PARK to DRIVE and my electric windows doesn't work either ! Everything else working fine and the car start normally !! The dealer cannot find the trouble and the car just have 19802 KM on it!!
View 3 Replies
My brother in law has a 93 explorer which developed a serious transmission leak and had to be towed home. We suspected a blown front seal, which we replaced. We also replaced the transmission filter and pan gasket. When we started it up, it seemed like it was stuck in gear and wanted to move forward no matter what gear it was set to. Even wanted to go in park and neutral. We topped off the fluid, and finally got park to work, but all other gears including reverse want to go forward and it seems as though it is not shifting at all. Could we have forgotten a connection of some sort, of could something internal been damaged when the fluid was lost?
View 6 Replies
I have a 1993 corolla auto trans and when I first try to take it out of park it will not shift. I noticed that when I push the brake pedal to the floor it finally shifts. I recently replaced the brake switch, could the adjustment be a problem?
View 1 Replies
I have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
View 1 Replies
Just cleaned out the oil seperator box on my 93 850, put new injector seals in and a new intake gasket. Start up the car ran rough for a little then idles like a champ. The problem-shift up indicator is blinking. Barely put my fut on the gas shifts up a gear then back down then back up, I think I unplugged something by accident.
View 1 Replies
I have a 93 taurus 3.8L V6 automatic GL. After I start my car up with my foot on the brake it won't shift into gear from park. But if I pump the brakes a few times it will then go into gear. What is wrong with my car?
View 7 Replies
I'm trying to diagnose a problem with my dad's 93 F250 7.3 diesel 4x4 with a ZF S5-42 5 speed manual transmission. It seems to not want to shift back into gear once the truck has warmed up, with 1st, 2nd and reverse being the toughest gears to get into. We've done a transmission fluid change with the required dextron/mercon substitute but the problem existed before the change and the change didn't seem to solve the problem any.
This problem didn't exist until I did a couple hundred miles of towing with it, some of which was done in 5th gear (overdrive?), so I'm hoping the 5th gear towing didn't ruin the transmission. From a cold start the transmission has no trouble shifting into any gear as well as with the engine off when either warm or cold, but with the engine idling and the truck at operating temperature it can be difficult to impossible to shift into gear, especially reverse.
I think heat has something to do with the problem because the shifts were worse a when its driven longer and during the tow/driving that was done in the last part of summer. It sat most of the time since then but we took it out today to test some things. Hot or cold the external hydraulic slave had roughly the same range of movement, but the drive line seems to jerk more noticeably like power is applied to it during a shift when its warm.
This all makes me think, even though the clutch hydraulic system is working like I think it should, that the clutch is not fully disengaging when at temp. I'm not a transmission guy so before I start throwing parts/labor at a problem.
View 8 Replies
I have a 93 F250 diesel 4X4 with the automatic, the transmission was rebuilt by a reputable shop les than 10000. miles ago, every few months it will act up, it will act like I put it in neutral then it slams back in gear, then it shifts very hard, sometimes it will not shift until i lift the throttle. Sometimes I can shut it off and when i start it again it will be back to normal, other times it will do this for a few days, then work fine for another month or two.
View 5 Replies
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
View 10 Replies
My 93 Honda Civic (manual T) is starting to be difficult to shift into gear. I mainly notice it when the car is idle and in neutral. I go to put into 1st or reverse and it won't go. I try all gears at that point, and it's the same. When it finally does go, it's a loud thud-like noise. People around look over at me! It doesn't happen every time, but I am noticing it more and more. And it's a bit scary when I have been at an intersection or something and I can't get moving. It has 189k. I have also noticed that the car is loud, too, when I am in reverse up our driveway and the clutch is slightly depressed.
View 7 Replies
190000 miles... Driving on the highway my car began to vibrate and lose speed. I had to shift out of overdrive before I could get the car to respond again. It continued to feel incredibly impeded. I could not push the car over 65mph and couldn't remain at speed going uphill. From a dead stop, the car accelerates incredibly slow in any gear. The engine feels impeded even in P and N almost like the trans does not disengage.
The trans will downshift and kick up RPM when the pedal is put to the floor like normal. What could be causing the trouble and how much it could cost to have repaired? I have checked the trans fluid in park at op temp and it's perfect. No fluid is leaking from the car. Car feels like it's in drive and I'm holding the brakes while hitting the gas... even in P and N so I don't think it could be brakes.
View 2 Replies
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 Replies
I have my suspicion about what is the culprit, and well, the likelihood of it contuing to work.
Occasionally when I am at a stop and try to shift into gear with the clutch depressed to the floor, it does not want to go into gear. So far, I have been able to wiggle the shifter around, try a few different gears then go back to first and it works. Also at a stoplight today, with the clutch depressed to the floor for a few minutes with the car in 1st, after about 3-5 minutes the car started to slowly creep forward.
What are your suspects on this one?
View 10 Replies
Recently my 93 Ranger 4.0 has started to take longer to shift into 2nd gear and the rpms are way up there. shortened 2nd gear then 3rd will be fine and so on. This only happens after the engine goes completely cold. I took it to a transmission shop and they said tranny is fine...Other than this issue the truck is fine.
View 6 Replies
I have a 93 f250 4x4 with a 5.8 liter with 69 thousand miles.. the problem I'm having Is if I put It in drive it won't shift out of first but if I manually shift it from 1st to 2nd to drive it works but shifts very hard. Sometimes it will shift in drive but It shifts really hard. I don't know what It could be. We just put the transmisson back into the truck due to having to change a broken flywheel. It just don't Seem like it has any power...
View 5 Replies
So my 92 blazer won't start now I put an new alternator in and it won't kick over it want to start but wont..
View 3 Replies
After replacing the lower intake manifold gasket, along with the plenum and valve cover gaskets, I've discovered my AC isn't cooling at all. During the above repair I unbolted the compressor and set it on the passenger side out of the way. Checked the low side pressure and had no pressure. Thought I might have loosened something and caused a leak. Hooked my gauges and vacuum pump up and vacuumed for about an hour pulling 29in. Hg. Turned off and after three hours the needle had barely moved. Decided I'd add some R134A until I got enough in to activate the clutch on compressor, read gauges and try to see where I was with it.
Initially I had readings of 100 on low side and only 50 on high side. I'd added about 2/3 of can of refrigerant and my clutch had activated the compressor. Turned off and checked the electrical connection to compressor which appeared okay. Honestly I didn't know what to do next. Fired up the engine again and still had the crazy reading when the compressor clutch kicked in. Actually it was doing what I think is called, "Short Cycling," on and off every five seconds or so. When the compressor was running the gauges would show fifty psi on low side and a hundred on high side. Also the sight glass on my gauges was filled with oil. I'd planned to put some dye in the system to show any leaks I might have, but with the way things were going I didn't get to it. This experience has shown me I've got a lot to learn about auto ac systems!
View 10 Replies
