How many bolts actually holding the intake manifold onto the heads. Are there more inside the plenium when you take the top off or can you remove the unit as one piece to replace the intake manifold gaskets?
View 1 Replies I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
2.4 Santa Fe ... I just took my Car to MOT inspection and found out there's a leak at my intake manifold and it's coming out of this place. it feels like brake fluid but my brake fluid is full?? I have seen many cars but never seen a part like this before. what is it doing there and why is it leaking ?
View 6 RepliesWhat are signs the intake manifold may be cracked? 2001 V10 Excursion....
View 4 RepliesI am about to replace the intake manifold and gaskets. I know all of that process, but first question is if there is anything i should do whilst in there. Second question; what can I do with my intake to get more power? Mainly just kind of wondering before I get my parts ordered.
View 4 RepliesLooking at a 2003 Prius with 77K miles. Turn the key, the engine starts, runs smooth for about 5-7 seconds. After that it starts to run rough and rattle, then shuts off. The only code I pulled was P3191. I pulled off the air cleaner to clean the throttle body, and noticed a small pool of oil in the bottom of the intake manifold. Is that normal, or could that be causing the code issue? BTW, I cleaned the MAF and throttle body, and the engine still does the same thing.
View 14 RepliesIt doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?
View 14 RepliesI have a 2001 F150 Super Crew 5.4. I had a leak where the water transfer connects to the intake manifold. I decided to get a new manifold rather than trying to repair it. The new manifold from Dorman came and the gaskets were built into the manifold. I torqued the manifold to specs. I replaced everything and it starts fine.
I can hear what sounds like a leak, but can't find anything. I checked every hose that is connected and they are all snug and connected. I had the check engine light checked and it said it was running lean on both sides (p0174, p0171). Also a p0122. I thought something might have damaged the Throttle Body Position Sensor, so I replaced it...but no change.
I'm still driving it everyday because I need to. It won't change gears so smoothly sometimes. The most noticeable problem is that the A/C doesn't work. It just blows hot air. And the worst part about it is...it does it even when the air isn't turned on! I just go around with the windows down...in 95+ degree heat...with hot air blowing!
This is my first time to attempt a manifold change out. What I should check?
There are two bosses on back of hpop cover that have bolts holding heat shroud for the exhaust. How difficult are these to remove? The drivers side looks fairly accessible, but passenger side I am not too sure of. I will be back to disassembling everything in a couple of days, and just getting a heads up on it.
View 5 RepliesI can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 RepliesI just replaced the turbo to manifold gasket and bolts but the but bolt closest to the engine keeps backing out.. i cnt seem to find a tool that can tighten all the way..
View 5 RepliesTruck has 107 thousand miles; had to take it in for an manifold exhaust leak. Mechanic said bolts are so rusted they break.
1) was there ever a ALERT from ford about these bolt's?
2) Thought i read ford had stainless bolts for this problem...
I've had F150's only since the mid 70's and this 04 has cost me more in repairs than ANY previous F150..
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesSo I had recently developed a leak in the up pipes behind the collector. Big surprise, right?
Well, a 6-point socket was spinning on the collector bolts (probably from rust) so I decided to cut the manifold to up pipe bolts. Got the up pipes off/out. Well after and <acronym title="Manifold Absolute Pressure">MAP</acronym> gas torch, I can't punch ANY of the bolts out.
There is little to no room to get to the bolts. (I have the down pipe removed.) At this point I'll try a few more doses of hot wrench and PB Blaster, but if I have to do the manifolds I'll just pull the engine, since chances are there will be at least one stuck bolt there, too. I really don't want to go that, but eventually I'll need to install my new oil pan anyway.
I have a problem with exhaust fumes in my 2003 Silverado truck. Initially, 3 head bolts on the manifold were found to be popped off. After replacing the bolts, the exhaust fumes in the cab still existed. The truck has been evaluated by a Cherolet dealership and 2 independent garages who found no system exhaust leaks. Obviously, I am very frustrated and not sure what to do next or where to go.
View 1 RepliesBolts breaking on the exhaust manifold. If so why isn't ford doing a recall on this problem I have a F350 V10 90K miles and 3 on the top drivers side are missing not sure on the passenger side. Is this a problem with all the ford engines I have never had this problem with any other truck or car I have owned.
View 5 RepliesI've got the dreaded broken exhaust manifold studs on my 2004 F250 V10. I don't drive it much (just 50,000 miles in 10 years) and confess I've ignored the hissing for quite a while. Is there really a permanent fix for these broken studs? Or should I expect to be replacing broken studs every 2 or 3 years?
If there is a permanent fix what is it? Special studs? Special manifold? I want to keep this truck a long time and don't want to be replacing these studs every few years.
Today I was on my way back home from a weekend trip to see family when the CEL came on. The car was running fine no problems (we had driven 200 miles). Gas mileage was good, good power, no weird noises, engine temp was fine (it was 100 degrees outside). But being how the car has 39k on it and its the most expensive thing I own; I pulled over and had autozone scan it for me. It came up as Intake Manifold Sensor. I have never worked on this car but Im going to at some point, I'll replace it myself if it isn't to hard. I am wondering if it is as simple as replacing the sensor or could there be an underlying issue like a blown intake manifold gasket (like i said the car was running fine though)?
View 6 RepliesOur F-450 with 102000 miles lost both turbos also broken exhaust manifold bolts. This truck carries tools fuel tank and sometimes skid loader on trailer. Heard lots of bad things about 6.4 liter motor now first hand experience. Asked dealer if 6500.00 bill could be reduced since so close to 100000 mile warranty and was told nothing could be done. Can not afford to sell truck now also have two other Ford F-250s newest one 2012. Is there any other approach that could be taken to get some relief from this expense.
View 14 RepliesTurned the key on my 2002 MC SS, V6, 3.8L, and the Intake Manifold exploded.
Intake Manifold Exploding on a GM V6, 3.8L? It sounded like a 12ga shotgun. Fortunately no one was looking into the engine compartment at the time as they likely would have been killed given the amount of shrapnel from this explosion. Note that the explosion was powerful enough to blow off the oil cap, which is screwed on with very thick threads.
The vehicle was at my mechanics at time and in his forty years he's not seen an intake manifold explode save for those residing on Top Fuel or Funny Cars.
One of the nozzles on the back of my intake manifold broke off. I don't know how to better explain it. The ones the back of the manifold closest to the firewall there are several hoses that hook to the manifold. The second one from the left broke.
View 7 Replies