Ranger :: 2000 Ford XLT - Clutch Pedal Stuck After About 15 Minutes Of Driving
Nov 8, 2015
I'll drive my 2000 Ford Ranger, 4cyl XLT about 5 miles to the store without a problem. On the way home, after a few miles, the clutch pedal will either jam at the top, or go all the way to the floor without engaging the clutch. If I wait 5 or 10 minutes, the clutch pedal will start working again for a short time.
If I feel the clutch pedal starting to misbehave, if I ride the clutch and don't release the clutch pedal all the way, and if I don't push the clutch pedal all the way down, I can keep driving the truck. As soon as I release the clutch pedal, it will jam up again, or the clutch pedal will go all the way to the floor without engaging the clutch. I don't like riding the clutch, but that seems to be the only way to get home once the clutch pedal starts jamming.
It certainly seems related to the engine warming, or heating up. Sometimes, after the clutch jams up, I'll wait 5-10 minutes and the clutch pedal will start working as if nothing every happened. So, it can't be strictly a hot engine, hot clutch fluid issue, right?
What would you attempt to replace first, the Slave Cylinder? The Master? Changing the fluid? Shooting the truck!?
View 8 Replies
Advertisement
So I have had an issue with my Ranger. When the car is cold it's fine. After a while...maybe 20-30 minutes of driving, the clutch will start to stick. No better way to describe it. I will take my foot off and it will stick on its way back. It starts subtle but the this will gradually get worse and eventually the clutch will seize up and I can't press it anymore and the car stalls and I'm stuck. The car cools off and everything will be fine no problem.....but the problem keeps resurfacing.
View 6 Replies
95 ford ranger clutch pedal very hard when hot. Will not engage clutch. Ok after setting for 1 hour.
View 1 Replies
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
View 14 Replies
When I bought my ranger used, the clutch felt ok. But as a couple weeks had passed, it started to get hard to shift. The clutch doesn't slip at all so a friend of mine said there might be air in the system.
I would pump the clutch pedal a few times and then it would shift ok for a while, then back to shifting hard. I found the bleeder and had my son assist me with bleeding the system. Everything was fine at first but I made a big mistake and now i have no pedal feel at all.
My mistake was i didn't realize what I thought was the reservoir was not the actual reservoir. There was a black rubber thing in the reservoir that I filled with fluid. My mistake was I needed to take out this black rubber thing.
So now i am stuck with no pedal and don't know what to do. When I pulled out the black rubber thing, the reservoir was empty so i filled it and it bubbled for a second and then stopped. Tried pedal at this point and there is no feel at all. It just goes to floor with no effort.
View 8 Replies
I've had my truck a few years now but for 2 it was basically parked. When I started trying to use it again I am having issues with the clutch now. When it is cold everything is fine, but on hot days or after I have been driving for a while It will lock the pedal up and will not let me dis-engage the clutch at all. Sometimes when it does eventually let the pedal down it will go to the floor and stay there for a few seconds until it slaps back up and engages slamming the truck into gear.
I have yet to try much. I'm not good at working on anything other than stereos in cars but I am willing to try. My thought is some water got into the system and is boiling in the lines but I am not sure. Places to start? I really need my truck going and the couple places I've taken it dont even want to try it seems like.
View 2 Replies
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 Replies
My wife has a 2003 Camry that we had to replace the clutch last year. Now her clutch pedal goes to the floor and does not return.
View 2 Replies
This is unusual. After driving into town for new tires, the clutch pedal was hard and I could not depress it after the tire tech parked the truck. It did finally depress with a pop, though the pedal functioned there after the clutch did not function properly.
At times it seemed to be ok at other times it seemed weak. I stopped by Autozone and checked the fluid, seemed low and I added some. Continued home not completely confident that I would make it. Had to make one stop along the way.
Once again the clutch pedal was stuck at the top and would not depress. I finally slid the safety switch up the clutch shaft to start the truck, when the engine started the pedal depressed. I was able to continue home but the clutch is not functioning properly.
View 2 Replies
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
View 6 Replies
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
View 16 Replies
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
View 2 Replies
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies
I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
View 5 Replies
I have a 88 ranger supercab 2.9l 4x4 with the fm146 trans and recently I have had a problem with my clutch master cylinder rod falling off my clutch pedal. I bought the new bushing and put it on and it was fine until yesterday. It wants to keep coming off. Is there a clip of some sort to hold it on or no. I looked at a few at the salvage yard and they did not have a clip just the bushing. So what do I do?
View 1 Replies
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 Replies
1998 Passat 1.8T FWD. My clutch pedal is stuck to the floor and wont spring back up. I can't seem to find the little tank to check the clutch fluid. I have heard the it uses the same tank as the brake lines do, but the tank that holds the brake fluid is full. Can it be the slave cylinder is gone? or just got a air pocket in the line?
View 1 Replies
I'm looking for a part number for the rubber stop that mounts behind the clutch pedal on the firewall for a 2001 Ford Ranger 4cyl 2.3L 5spd Manual. Can't seem to find it on the web. It looks like it snaps/presses into a mounting hole behind the pedal. The original one decided to disintegrate and now I get a nice knocking noise when ever the pedal is depressed.
View 7 Replies
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 Replies
I've been driving manual 12 years, all my driving life, and been in 10+ manual vehicles during that time, including a 10+ year stint in a 1.8T Passat with a 5-speed.
In all that time, and all those experiences, I've never replaced a clutch, damaged a clutch, or had one problem. In fact, I consider myself a very good operator of the manual transmission.
This is preface to my current situation. 2009 Tiguan (early build) 2.0T 6M, driving at 57mph in 6th gear - downshift to 4th to pass a truck and WHAM. Grinding, confusion, and then the clutch pedal stuck straight to the floor. Glide to a stop on the side of the bayou road.
Totally immobile vehicle. Impossible to shift into gear, or get the pedal off the floor except by pulling. Smell of acrid smoke.
VW dealership says "we're doing a courtesy warranty repair" on the clutch, flywheel and bearings, as if it's my fault. Impossible. This is a mechanical defect if I ever saw one.
View 9 Replies
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies
