Ram / SRT10 :: 1988 318 / 5.2 Runs Rough And Stalls When Hot (after Around 20 Miles)
Jun 29, 2014
Truck in question has 175k, is the TBI version (fuel injected carburetor design), has had the plugs cap and rotor replaced fairly recently.
When cold, it starts and runs normally. As it warms (after around 20 miles) it starts running rough, then after getting warmer/full operating temp, it will stall at stop signs and runs very rich - so rich you can smell the unburned fuel. At this point it is also difficult to start and requires adding some gas pedal.
I am thinking a vacuum issue, or something that is not allowing it to transition from the warm up cycle to normal cycle.
View 1 Replies
Advertisement
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....
View 2 Replies
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
View 4 Replies
I have a 1997 Buick Park Avenue with a 3800 series II motor that runs perfectly in dry weather. However, in wet conditions, rain melting snow, etc. it will begin to miss and throw out a P0300 OBDII engine code. This is the code for multiple random misfire. If I leave it to idle on its own it will get worse and die out right. Sometimes restarting it is an option though it still runs rough, but I can limp it to somewhere I can work on it. I think its electrical, since it doesn't seem to get the spark it should though fuel doesn't seem to be a problem as you can smell it after a bit of cranking.
I've been battling with this thing for over a year so far and have replaced the following, ECU, all 3 coil packs, spark plugs/wires(newest parts), mass airflow sensor, cam position sensor, ERG?(emissions deal I believe, mechanic friend put it on) valve. I had the battery trickle charged and tested at an Autozone, I haven't had the alternator tested yet.
Its a very frustrating problem, as far as I can tell I've replaced everything on the ignition system with the hopes that it did the job only to get stranded during the next long rain. It does take quite a while in wet weather for it to start acting up, but once it starts missing a little bit, it doesn't stop until the entire engine compartment has had a few days to dry. Engine temp doesn't seem tosolve the problem dry out. I'd also like to note that I've noticed on this latest trouble that the interior lights have been flickering and headlights too. It may have been doing this earlier, but I hadn't noticed if it was. I'm going to check what kind of voltages the alternator is throwing out next time I have it running.
View 6 Replies
I just bought this 99 f250 7.3 Powerstroke last week.. drove it all week fine, I car pool with a family member to work and asked his girlfriend to plug my truck in for me, well she didn't and it had stalled on the way home one morning but started up after cranking a few times i thought nothing of it. Drove it a little bit that day and it was fine, while I let it idle in my drive way as I prepared to go work it started running really rough then died. It took a long time to start again..now it's happening all the time. I changed the fuel filter and someones telling me there's air in the lines..
View 5 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
Let me start with I have a 2003 f250 5.4. The motor blew on my truck and I had a 100k motor dropped in it. I've put new spark plugs, ohmd out the coils. I tried both sets of injectors. cat delete and new fuel pump. It has rough idle and stalls but runs fine at higher rpms. Also has basically no brakes. I am thinking vacuum but I've check all the lines. No codes either!! also cleaned throttle body.
View 4 Replies
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
View 2 Replies
We have replaced crank position sensor, ecm/ coil packs and computer. got good pressure on fuel rail. Starts cold, will run normally for approximately 5 minutes before it dies and will not start.
Sometimes we can hold accelerator to floor and it will "hit" a few licks but promptly dies when accelerator is released. We've checked fuses and relays; what are we missing?
View 1 Replies
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 Replies
I have a 2001 ram 1500 sometimes when I go to start it, it begins to run rough like it is off timing and then it dies, do a restart and it runs ok, it has done this a few times when I come to a traffic signal. it just starts running rough and the stalls.
View 5 Replies
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 Replies
My 1988 jaguar it don't matter whether the weather is hot or cold it will run great for about six or seven miles then it will just shut off like you turned the key off. well then you can wait about 15 or 20 minutes and ti will start and run fine for another few miles off again.
View 11 Replies
My1988 ford ranger 2.9ltr stalls when driving or after it warms up. Will restart most of time a few minutes later. Runs smoothly till it dies. Changed fuel pressure regulator and fuel filter. Drives for miles before it stalls sometimes.
View 5 Replies
my 88 camry will start and idle fine however whenever you attempt to accelerate the vechicle the car trys to stall and hesitate badly and will not move. i have changed the fuel filter the spark plugs and plug wires i cannot figure it out. also this started out of nowere the car was driving i had been driving for about ten miles stopped at a red light and that is when the car started doing this.
View 9 Replies
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 Replies
For the past couple weeks on the way home from work the ICE runs non-stop for 20+ miles. My drive is 25 miles and the weather has been 105+. In the morning everything seems to work fine. In the afternoon even with the AC off, battery almost fully charged the ICE does not shut off at all even at a stop. I even tried putting it in EV mode and it tells me Not Currently Available. My Prius is a 2012 3 with 5500 miles. Is this normal in hot weather or is there something wrong??? Also the mileage sucks, in the morning with the AC on, weather around 90 I get 55-58mpg. In the afternoon I get low 40's even with the AC off.
View 19 Replies
2010 Cobalt, LS 2.2 Ecotec, with 13.7k miles. Oil level normal and battery voltage = 12.5V.
I've bought the car new in Feb. 2001. Car started and ran normally for the work commute on Friday, 9/2. Today the Cobalt starts normally, runs for 2-3 seconds, and then stalls. The accelerator has no effect. It's already been towed to the dealer..
View 1 Replies
I have a 2000 Subaru outback (150,000 miles). Recently after starting, the car will feel sluggish or like it's pulling. When I come to a complete stop it will shake and feel like it's about to shut off... and recently it has been shutting off. Last night I changed the spark plugs, spark plug wires, and fuel filter... after that the car was driving worse. My check engine light is on and the code is for a knock sensor. Also there was oil on my spark plugs which I believe is an idication that there is a broken or leaky gasket. I am at a loss... would the leaky or broken gasket cause car the run sluggish and stall, would a faulty knock sensor cause the the same? I also need to get my rotors changed but I don't think that would cause any of this.
View 3 Replies
