Prius (Gen 3) :: Check Engine Lights Up - No Error Code Detected
Feb 18, 2016
My car is a Prius Plus 2012.
One day, I decided to go to a mechanic to clean the EGR pipe. Only the pipe, not the whole EGR. It was an extremely simple operation a mechanical one, not electrical etc. Starting from that day, when I go with the car, from time to time, check engine lights up. For a fraction of a second to up to 2 seconds then it disappear.
The car behave itself without a problem. But still the on-off check engine is really annoying.
So a went to the dealer. Put the car on tester.
Result: no code error !
I went to another garage , put another tester on the car, no error..
How can I actually see what the error is if nothing is stocked in the ECU of the car?
View 4 Replies
Advertisement
As far as the owner can tell, the car is running fine. He hasn't driven it aside from getting home after the light came on. It seems to give a very informative error message. What it's saying?
View 4 Replies
AutoZone provided this code for my check engine light: P0010.
Definition: Intake camshaft position actuator circuit open
Explanation: ECM has detected a low voltage on the VCT circuit
Probable Cause: 1) Open or short circuit condition on the VCT circuit; 2) failed VCT solenoid
Is there a part I can replace myself that can fix this, or is this a dealer repair?
View 2 Replies
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
View 8 Replies
I had a check engine light cane on. I took it for it to get checked and they gave me this code- P0457 EVAP small leak detected. ECM has detected a large leak in the EVAP System during a system monitor test.
The paper said I had a leak in the Evap canister or hose. I took the truck to a mechanic and was told I had Bad oxygen sensors. Can Bad/Dirty oxygen sensors make this error code come up?
Exactly where the oxygen sensors are? I was told they were behind the mufflers but I didn't see any and the diagram I found was not accurate.
2002 Ford Ranger XLT v6 extra cab.
View 2 Replies
My r32 mk5 is throwing that code.
I replaced new o2 sensor with oem new one.post cat on driver side.
I have erased dtc and drove 15 miles dtc came back again.
Now i have replaced catalysator on driver side and same thing again.
View 2 Replies
The CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 Replies
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
View 3 Replies
In the past few weeks I have seen an intermittent "Level Error-Workshop". However every suspension function has worked perfectly, and no height was lost even while sitting at the airport for a week.
How to track down the leak. I can see a tank pressure of about 13 PSI. Is that about right. I did a raise / lower while VCDS was connected and there was a pressure drop to about 11.7 PSI but no level error. What is the correct range of tank pressure settings?
Address 34: Level Control Labels: 3D0-907-553.lbl
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0005521
Shop #: WSC 01065 000 00000
VCID: 2757057592F60B6
1 Fault Found:
01583 - Leak in System Detected
000 - - - Intermittent
View 4 Replies
2003 1.8t passat wagon. 50k miles... The check engine light came on today. Oil and engine temp are fine. Can most shops plug in and diagnose? Can I get one of those code readers at Advanced Auto parts to read the error code?
View 5 Replies
What is the meaning or the fault concerning 4608. The above error code was reported on the computer diagnose machine and it referred me to look into the vehicle ownership manual book BUT its rather unfortunate that i could not find that book. So, what to tackle or replace on the engine to enable the check engine lite go off.
View 17 Replies
I got a P0118 error code on my car. Looked up some things and most people were saying change coolant temperature sensor. I changed it 2 days ago and have not had a chance to clear the CEL. Its still on now, guy at Autozone would not clear it, said it was against company policy.
Will this turn off automatically once problem corrects itself? I went to Autozone and had them rescan the error, this time another code poped up P0444, EVAP(Evaporative Emission System)Evaporative Emission Control System Purge Control Valve Circuit Open. What this can be?
View 3 Replies
I own a 06 limited and my Check engine along with VSC lights came on. Autozone read the code and it is a P2195 error. According to AZ the O2 sensor cost $500, according to websites the fix is O2 sensor and manifold ~$1800. I don't have that much money. The dealer told me that it was ok to drive with warning lights on. I checked the MAF sensor and it is clean. The O2 sensor or A/F sensor Stuck Lean - bank 1 sensor 1. If I want to do the work myself, any diagrams, picts, instructions etc......
View 8 Replies
I have a CEL on my 2007 Avalon so I decided to take it to Autozone to get a scan. Error code P0015 was returned. This code has to do with B Camshaft Position, Timing Over Retarded (Bank 1). I've done a little research and I've read that this could possibly from a dirty screen on the Oil Control Valve, the OCV itself, or the Cam Position Sensor. Before replacing parts, what I would like to do first is to check/clean the screen on the OCV. Secondly, I would like to swap the Cam Position Sensor to a different bank and see if the other bank throws an error. If the other bank throws an error, then I know the sensor is bad and needs to be replaced. With this said, I am having trouble locating the OCV and CPS. Where the valve and sensor is located. A diagram would be useful.
View 14 Replies
I got a 2012 Hyundai Accent SE manual 112000 mostly highway miles. For a month now I am getting the MIL on and P2191 code (System too lean at higher load bank1) after erasing the code it appeared again in 3-4 days. I replaced air filter check all valves and vacuum in air flow, changed to premium gas. Pipe that connected to the valve from EVAP system looks not damaged and valve works as intended. While changing spark plugs I noticed that all of them were quite charred. I am thinking to replace both O2 up/down stream sensors. Which not OEM sensors would be the best match for my Accent?
View 11 Replies
I recently bought a 2007 Hyundai Sonata Limited from a private seller. This car has been perfect for the few weeks I've had it. Now, my check engine light came up and the error code "P0660 Intake Manifold Tuning Valve Control Circuit / Open Bank 1" popped up. I'm not really sure what piece to look for, or which connectors to check.
View 3 Replies
I have two codes off my "digi moto lite" obd2 scanner....
P0201 - internet search suggests it's a fuel injection code....
However I can't find anything on code C3203....
View 8 Replies
I am far from home. Taking a road trip. Day 2 out of 6. My check engine light came on, so I just pulled over. All fluids were fine. Found some place to read the code:
P2757 TCC pressure control Sol Ckt Perf / Stuck off
The guy said it was something to do with trans.
View 3 Replies
From time to time, the engine lights comes on with error code P0365, it usually disappears within two days (it disappears by itself), but it appears once per month and stays for two days.
The code scanner says :P0365 Camshaft Position Sensor B Circuit Malfunction (Bank 1)
Do I need to change the sensor? and where is it located?
my Sonata is 2009, 2.0L (Korean imported) 4 cylinder ...
View 8 Replies
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 Replies
I had a Check Engine Light a couple months ago, and I took the car to the garage to have it checked out. They told me they got a Fuel Pressure Sensor malfunction code, and that the sensor had to be replaced. I did so myself, an it is ridiculously easy, and the car worked fine. I noticed the Check Engine Light blinked a couple of times while I was driving, but never got steady. A couple of days ago, it did. Out of a bad gut-feeling, I purchased a ODBII scanner, and I scanned the car myself. I got the same error code as the garage did, but the sensor should be fine.
View 5 Replies
