Both of my front sway bar links have a bad joint and are making a bad noise.. I purchased the replacements and tried to loosen the nuts with no success. I put some oil to loosen them and will let them set over night. Next attempt will include a breaker bar.
View 4 RepliesI plan on replacing as I have a clunk happening. Thought I'd try here first.
Is there a brand that's better? 1Aauto has OEM. Is there a brand that's better or makes a difference?
Or is a front sway bar end link a front sway bar end link?
I want to change the front sway bar links on a 2005 Camry that has been driven in central New York (ice, salt, corrosion) for 10 years. There is definite wiggle and noise. I recently replaced the ball joints. That was difficult. How difficult is it to remove the sway bar links? Looks like a 5MM or so allen wrench is supposed to hold the ball joint type link to allow 18MM nut to be removed. A 5MM allen wrench is about 4 inches long and skinny. An 18MM wrench is about 12 inches long and beefy. I am skeptical about breaking the nut loose.
Will I need to heat the nut? If yes, how? With a simple propane torch? If yes, how does that work? Apply heat and wait for a sound that indicates the rust has broken? Apply heat for a time, try to hold with the allen wrench and try to undo the nut? Keep trying that again and again until it works? This would be after multiple rust busting spraying to make this easier. I used a 4 inch grinder to grind the nuts off the ball joints to remove them (I know how that sounds, but that is what I did). Thoughts about that for the sway bar links? I am a bolt turner who can stand some aggravation.
What is the correct length of the front sway bar end links. I need that info to order replacements for my 04 X EB 6.0 4x4. I just don't want to wait another day.
View 3 RepliesI'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesOne is coming apart, so I'm gonna replace the pair. My Chilton book says to jack the front end up. The part instruction sheet makes no mention of doing that.
Raising the front would allow the control arms to hang. That would seem to me to make it harder to deal with the links.
Can the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 RepliesMy 04 6.0 Limited and both front and rear sway bars. The front links keep wearing out after 3-4000 miles. But, I saw someone in here put F350 Sway Bars in their Excursion? REALLY?? Is this right or is this snake oil? Is their another way to fix the front links so they don't wear out so quickly??
View 4 RepliesThe Honda dealership told me my 2005 CRV has loose sway bar links. How are these fixed? They quoted a price of $290 for the front links and $374 for the rear links. Does this sound reasonable.
View 14 RepliesMy car is a 2000 Corolla CE.
If I replace the rear sway bar end links, do I need to get an alignment? (I just got an alignment 2 days ago). Here is a DIY on replacing the rear sway bar end links: [URL]
The top attaches to the strut.....what is the bar the other end attaches to?
I just installed rear sway bar & links, this made a world of difference in the way the car handles as soon as I made the first turn I could feel the difference in the car it definitely corners flatter, the install only took about an hour did it in the driveway on ramps, I installed the kia sway bar 555102T000 the bar is 18.3 mm while the stock one is only 15mm I included some pics...
View 8 RepliesMy mechanic says I need to replace both front sway bar links on my 2002 Jetta....I am, of course, hesitant to do it at this price. How critical is it to replace? Can I get junk yard sway bars to make it cheaper? And can I do it myself (have no experience fixing anything....
View 11 RepliesI've been having the loud clunk under the drivers side floor, that many others have as well. Did many hours of research and replaced the sway bar end links. Napa only had the left side in stock so I did it first last weekend and did the right side this weekend. One thing I noticed when doing the right side was the hole in the frame was all wallowed out. Drilled out the bushing in the upper end link and used a bigger bolt to fill the gap up. went for a drive and the clunk was way worse than it ever was still on the left side. So I took off the left one and went for a drive. Sure enough no clunk, the left one was wallowed out as well. So I did the same thing on that side and the evil clunk is finally gone. Just thought I would throw that out that if have a clunk after replacing the end links, Check the upper holes.
View 14 RepliesSo putting the new extended links on my truck, not sure if they are supposed to be seated flush on both the frame and sway bar itself before tightening them down. This is how they are sitting now --
You can see a little gap between the rubber fitting where the bushing sits and the frame mount. Just wanted to make sure before I torque it down. Its the same on the other side as well. They are sitting flush on the sway bar.
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 RepliesI'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 RepliesAfter 2 months my hellwig sway bar is starting to make a lot of noise I've checked to make sure everything is still tight and it is. It does it on sharp corners and braking ....
View 2 RepliesChasing a noise in the front, seems to be more on the passenger side, and I think I have it narrowed down to the link ends or subframe. I have ST coil overs, came on the car, and already did the 034 mounts and bearings to solve another noise but this one is different. The links are original and I saw some performance ones that are a bit shorter for a slightly lowered car. Should it have shorter ones due to the coil overs?
View 5 RepliesTrying to change the front sway bar bushing with a PU version? Does it improve handling and steering feedback?
View 1 RepliesSo I'm backing out of my driveway today and I hear the loudest (in one of my cars) double clunk noise ever, coming from the passenger side front. Turns out one of my kw v2's decided it wanted to try and come apart at that corner.
Note: I had one side on a jackstand and could not find the cause until I removed the front swaybar endlink. It was putting tension on the arm and not allowing the movement to be found.
The shock insert inside the coilover body was moving up and down about a 1/8 inch clunking at the top and bottom of its travel. This is the retainer that loosen causing the clunking. I found that the spanner wrench from my dewalt angle grinder, fit the retainer well enough to tighten it down snug.
I’ve noticed that when I close my C4 passenger front door it makes a chinsey hollow twanging noise. However my driver front door makes a nice high quality and solid thunk.
View 9 Replies