Prius (Gen 2) :: CEL Going On And Off - Code P1221 / Fluid Control Valve
Nov 29, 2012
My check engine light was going on and off, then stayed on. Took to dealer, said it was fluid control valve. Replaced at a cost of $544. (Still smarting from sticker shock.) Now, the heat does not work in my car and last night the Master Warning Light went on, as did the light for high coolant temp. warning. These flashed on then off. Hasn't happened again.
Questions: Should I be worried if the lights only flashed briefly before going away? Is it likely the replacement and lack of heat are connected?
View 11 Replies
Advertisement
i have a 2005 Toyota Prius that the air conditioner wont work in. it has Freon in it the compressor wont kick so I did some research and my cooling fans aren't kicking on so I did a by pass test and the cooling fans motor is good they just wont kick on. I just replaced my 2 cooling fan relays and they still wont kick on. the check engine light was on in the car when I got it. it throws the code P1121 coolant valve control. I got the part just got to get it put on. Could this part stop my cooling fans from kicking on or my ac compressor from coming on.
View 3 Replies
The check engine light on my '05 Prius has gone on and off a couple of times and is giving me a P1121 code, which I found out means "Coolant Flow Control Valve Position Sensor Stuck". Does this have anything to do with the hybrid electric coolant pump that was replaced under recall a while back?
View 5 Replies
It's been a long week for me and my 2007 Prius. Brought it to the dealer after receiving my first ever CEL. I have 222,000 miles on the vehicle. The a/c was also blowing warm when the CEL came on. They checked that and told me that the compressor was "breaking up." Then they call me back to tell me that my 12V battery died. They asked me if I had problems with starting the vehicle. I said never. Never had any issues with the car in 222,000 miles.
Well, told them to replace the battery (no choice) and the car is 5.5 years old in Florida heat so it was ready to die. Very suspicious that it died while they had the vehicle, but what can I say. Told them to not repair the coolant flow valve or the a/c until I could investigate further on my own. CEL is now off. The a/c is blowing cool again.
View 10 Replies
The check engine light came on yesterday. 2004 with 115K. Auto Zone read the codes and they are as follows:
Definition:
Idle Air Control Valve control circuit.
Probable Cause:
Open or short circuit condition.
Poor Electrical Connection
Failed IAC motor
View 11 Replies
Got Engine Code P0022. Listed several things, Cam Position Indicator (replaced it) and CVVT Oil Control Valve Bank 2. Dealer calls them "front" and "rear". Is Bank 2 the rear (Black or gray also).
View 1 Replies
I need the PCM pinout for a 2002 F150 4.6 For the Purge Control Valve Circuit. If possible the wire schematic would be nice also. Getting code PO443 (( hard code )) I have checked battery voltage at valve connector with key on (( 12.2 volts )) valve resistance is at be 35 ohms so I'm thinking I may have a bad wire or a bad PCM .
View 2 Replies
I have this sensor unplugged. Is there a way to defeat this sensor so I don't pull this code?
View 3 Replies
2004 Prius, 98K miles ... I recently replaced the coolant control valve (received code P1121) and added coolant. Trouble codes were cleared. I am now getting the red triangle intermittently. When I drive the car, after a few minutes, the red triangle comes on. I can shut off the car, and turn it back on, and the red triangle comes back after a few minutes. The car seems to drive normally.
View 3 Replies
I was getting a check engine light with a P1112 code, so I had a mechanic replace the coolant flow control valve. There's a TSB on that and it seems to be the thing to do. But after the replacement, I'm getting overheat warning light whenever the engine needs to work hard. Also, the cabin heater only works when the gasoline engine is not running... when the engine is off, I get heat (though it's not as hot as I'd think when I have it on max heat), but when the gas engine kicks in, the cabin heat disappears.
View 8 Replies
My wifes 2008 prius check engine light just came on. Its the control valve sensor. My question is, does that have any serious impact on safety? I've heard mixed on what this valve does (overheating etc).
View 6 Replies
For several months now, my 2007 Prius has been making an intermittent buzzing sound from the engine bay. When I first heard it, I thought I had hit the little lines they cut into the road to let you know you've drifted over the center line - the sound is like that, a low-pitched buzzing noise. Today, the check engine light came on as it was making that noise. I put a code reader on the car and got P1121, a bad coolant flow control valve. Wondering if the sound and the faulty control valve are just coincidental or if the valve might make that noise when it fails? And if not the valve, what the sound might be?
View 19 Replies
I had the red triangle pop up on my Prius. I codes I got P0A93 and P1121 I needed a new control valve and inverter water pump. I installed both the valve and the inverter pump filled it with new coolant and bled both systems.
I went into maintenance mode so I could run the motor and bleed out all the water. My question is the red triangle is still on in my car when I start it up.. Is there some way to clear the red triangle or does it just go away on its own? Not sure what to do.
View 13 Replies
So I drive a 2008 and a couple months ago I started getting the Check Engine Light. Codes P1121 & P1116. Found out it was most likely related to a faulty Coolant Control Valve or Electric Water Pump. Since the pump was just recently changed I went ahead and got the valve changed.
The light is still coming and going but now when I go on the expressway that red triangle with the exclamation pops on with a little beep. Only pops on for a couple seconds and keeps coming back until I drive a bit slower.
View 1 Replies
What is the to cause to check engine light go off. I will take my car to auto zone tomorrow morning to hopefully get a code and see if I can fix it myself... if not, then I am going to have to go to the dealership.
View 19 Replies
How to fix the HCAC bypass valve P1436 code?
US TSB EG015-02
M.I.L. "ON" P1436-HCAC Bypass Valve Improvement, 2001-2002 Prius.
(Road salt may cause issues with valve. possible fix is to replace the Front Exhaust Pipe Assembly if any shaft binding is evident.)
View 1 Replies
I have read all the posts pertaining to this code, replaced my coolant flow valve, bled all the air out of the coolant system and still am getting the cel with the 1121 code.
I have tried setting multiple coolant flow valve positions, checked all wiring in harness, coolant level is full in rad and reservoir, checked temp sensor at bottom of storage tank, checked pump operation at top of tank to attempt to clear this code to no avail.
Is there a default position the valve is to be in before cold start up?
Is there anything else that can trigger this code? What am I missing?
View 11 Replies
I have an 02 f150 5.4 and since I got it it hasn't had cruse control. I went to a local ford dealership and they ran the vin and didn't find any recall on it. Under the hood on the master cylinder there is brake fluid coming out of the brake control switch. Would I have to do something with the harness too?
View 9 Replies
My check engine light was throwing the code P1121 for the coolant flow valve. Toyota replaced it under a warranty enhancement (I have 134k on it), and since then my mpgs have gone from 46 to 50.
My AC is working much better now, too. My theory is that the valve can be in a semi-failure mode for a long time before throwing a code. Now that My coolant is flowing the way that it should, heat is being dissipated more efficiently.
View 4 Replies
This is a 2008 Prius with no check engine light or other operational issues. The car runs fine. When doing a health check with a Techstream scanner (new toy), it shows the code U0073 along with U0123, 124, 126, and 293. Need to further diagnose what may be wrong?
View 7 Replies
I replaced both rear pads calipers on my jimmy. Its 4 wheel drive. Now after installing them, I tried to them, and i nothing from the bleeder valve s. Someone said I could have the wrong caliper on the wrong side? Is that even possible? Also, the manual food this truck says it may be necessary to use a scan tool cycle/bleed these brakes. Ive changed calipers etc before, never had this issue on other vehicles.
View 19 Replies
