I'm still trying to get my project 2001 Prius to attempt to start the ICE. I can drive the car around electric only, so MG2 is OK. I see a pulse of current going to MG1 as it does it's startup tests. So I'm thinking maybe the MG1 position sensor is faulty. Where on the transaxle the MG1 position sensor wire is located?
View 9 RepliesBackground: Check engine light indicated a problem with the throttle position sensor (unfortunately, don't have the exact code). The TPS on my model ('96 Dodge Intrepid 3.3L) is the non-adjustable type. There are three wires going to the TPS -- a power source, a signal wire, and a ground. The TPS acts as a potentiometer and depending on the throttle position, sends a voltage signal down the signal wire to the computer.
Here's my question/issue: After disconnecting the TPS, I tested the three wires with a multimeter. Power source (5V) and ground were fine. But I'm getting a voltage reading of about 4.35V on the signal wire. It's my understanding that with the TPS disconnected, I shouldn't be getting any voltage on that wire. Does that sound correct? If so, what would be causing me to get a voltage reading there? I'm assuming some type of problems with the wires, maybe an exposed wire on the signal wire somewhere?
I have a 2001 ford explorer sport and realized that the oxygen sensor on the passenger side behind the cat was unplugged from the harness.
I am unable to find the harness and dont know where its supposed to go.
I would like to get this fixed right away but can not find a diagram anywhere, or a manual...
The "Check Hybrid System" message came up on my dashboard. I took it to the dealer, and they said the temperature sensor on the transaxle was giving erratic readings. Unfortunately, they said that the only way to fix it is to replace the entire transaxle. They said I could keep driving it and that it would probably go into disabled mode before it caused any more damage. What I should do? It's a rebuilt 2012 Prius with 25k miles.
View 19 RepliesHow to do the transaxle fluid change and finally did it myself. I dropped and clean the pan and put new gasket. The MPG dropped a little, I was getting 44.6 before fluid change and after fluid change it dropped to 43.3 ... Why this happened.
View 1 RepliesAfter heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 Replies2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesI have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.
View 2 RepliesWe bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
I've a 2.0L Santa Fe CRDI 4WD, 2003. My Crank position sensor has blown. My question is, does the timing belt have to be replaced with the sensor, or can the sensor be replaced alone? I know the belt must be replaced with petrol models but I've been told it may not be necessary with diesels.
View 1 RepliesI am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesGetting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
my old lady has a 2001 olds intrigue with the 3.5L in it. Sunday evening we replaced the Throttle Position Sensor and the Coolant Temp Sensor. Monday she was on her way back to Iowa and the tempature gauge spiked up to the Hot area. I looked it over and could not find anything wrong. I sent her on her way and she made it about a mile before it did it again. The car will spike up to the hot area but the motor shows no signs of over heating. I checked the temps with a heat gun while the car is idling and read out Thermostat housing-160, Rad-80, Rad hose-130, and coolant 170. I than ran the car up so it shows on the gauge its hot and than checked again, it than reads Thermostat housing-172, Rad-100, Rad hose-134, and coolant 184. If I am running it at 1500 rpms it will spike up but once i take it up to 2500 rpms it drops back down to normal on the gauge. I am lost for what it could be.
View 19 Replies2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 Replies33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
Yesterday the Check Engine light came on, the code was P1121 Accelerator Pedal Position Sensor Error, Performance/Range. I have not yet had the pedal replaced related to the recall (bad me), is the sensor incorporated in the new assembly or is this separate and I'll need to replace it?
View 19 RepliesThe Check engine light on my 2006 Prius came on and I used my OBD reader to determine the code was P1121 - "Accelerator pedal position (APP) sensor - range/performance problem". I cleared the code to see if it would register again and a few weeks later same code showed up, but after driving it awhile the check engine light went out with out me clearing it and it remains off. The car drives normally with no other problems and when I monitor the APP sensor output I don't see anything particularly unusual. I can spend the $300 to have a new pedal installed, but I'm not sure there's problem especially if Toyota's design allows for a non-catastrophic failure mode.
My question is how does Toyota's engine control module manage a failure of the APP sensor? Is there a fail safe backup or is there potential for loss of throttle control like we heard about years ago in the news?
I took the car out for a little spin about 8 miles. We where about .5 of a mile from the house and there is a section where you have to stop on a little bit of a hill. I stalled the car due to the new Dm clutch then headed to the house and the car started to run like crap. I hooked up VAGCOM and had this code:
17748.P1340 camshaft position sensor-G40/ Engine speed sensor-G28: incorrect allocation(#1)
I swapped out the 2 cam position sensors and cleared the code and started the car and it still ran like crap. I just happen to have a new Cam position sensor(hall sensor) so I swapped it out in both cam positions one at a time and cleared the code and the car still runs like crap.
Is there a way to check(test) with vagcom to see if its one of the engine speed sensors?