Prius (Gen 1) :: Check Engine Light Turned On - HV ECU Malfunction
Nov 9, 2010
This morning, I tried to start the 2003 Prius and got a 'check engine' light and nothing. The cabin lights were bright so the 12V looked OK. After three tries, I used the VOM and measured 12.55 V on the battery. But the traction battery level looked unusually low.
So I tried again and it started. Using the ScanGauge, no codes were displayed. So I turned the car off and on three times and cleared the "check engine" light. Then I connected the Auto Ingenuity and read out:
P1636 - HV ECU Malfunction on the HV ECU to ECM bus.
C1213 - HV ECU Communication Circuit Malfunction between HV ECU and Brake ECU
P3002 - HV ECU Communication Malfunction on the HV ECU to Battery ECU
So it looks like there was an HV ECU problem that 'cleared while testing.' Certainly it makes sense to inspect the HV ECU connectors and re-seat them and clean out any debris.
View 2 Replies
Advertisement
I always take care of my car oil changes on time. And in the last week my check engine light turned on for a few hours then turned off. And today it turned on again. I kinda regret getting rid of my scan gauge now.
View 11 Replies
Yesterday, I was driving home in EV mode, PHEV on, about 80°F, no hills, not accelerating, SOC about 4 bars, about 1/2 mile out, when it dropped out of EV mode, and then I got the red triangle and the check engine light. Today I grabbed the code with an OBD2 reader, and got this:
Freeze Frame Information:
1. DTC for which Freeze Frame was Stored - P0A92.
2. Engine Coolant Temp - 138.20 °F.
3. Engine RPM - 1,888.00 Rpm.
4. Vehicle Speed Sensor - 14.91 Mph.
5. Intake Air Temperature - 96.80 °F.
6. Time Since Engine Start - 101 Sec.
7. # Warm-ups since DTC Cleared - 74.
8. Distance since DTC Cleared - 706.50 Mi.
9. Control Module Voltage - 13.69 V.
10. Ambient Air Temperature - 80.60 °F.
11. Accelerator Pedal Position D - 30.98 %.
12. Accelerator Pedal Position E - 46.67 %.
13. Time since DTC Cleared - 30 Hr32sec.
Does this happen because it's in EV mode? Do I just have to put up with it every so often? (This is the second time it happened.)
View 4 Replies
I own a 2005 prius. It is stock and i recently had the check engine light pop up as well as "problem" when car was started and 2 lights with exclamation point, one on a car and ones in lil brackets. I believe it is called a "hybrid malfunction light". Well one day they all pop up and about 3 days later theyre gone. Only thing i did was fill up the tank, when they came on only 1 bar was left on the tank. My question is should i still take it in to see whats wrong with it? and what could of caused both lights to come on?
View 1 Replies
My 2005 Prius has 105,000 miles. The check engine light came on for the first time ever. Dealer will diagnose tomorrow. If it's the main battery, should I sell it?
View 3 Replies
My check engine light went off last month and when I had it looked at my dealership they said it was due to the seal where the gas cap locks into I believe. Anyway, a week later my light went off again and now they are saying it is the charcoal cannister which I found out is very expensive. Here are my two questions. First of all, can I get this part replaced and installed at a non-dealership? My second question is since they reset my check engine light, it came back on a few days later for two days and then turned off completely. Should the light have turned off on its own? Should I be concerned that it is no longer on? It just makes me wonder if they diagnosed this issue correctly or not.
View 7 Replies
This morning I started my 2008 Prius (approx. 31k miles) and found the big red triangle with an exclamation mark and check engine light turned on.
I drove my car <1 mile to a smog check station where they ran a diagnostic on it and came back with the P0A9C code.
A quick internet search turns up that this is "HYBRID BATTERY TEMPERATURE SENSOR "A" RANGE/PERFORMANCE."
View 5 Replies
So this little gem of an SUV has been good enough to me over the year that I have had it, but it is one of those used vehicles that has me scared to look underneath cause there is always something a miss.
I have been having some power problems and the OBD check engine light has been coming on. The engine like to putter like if it's not getting enough fuel from a clogged fuel filter when it gets going, hot or cold. Have confirmed that the fuel pump is with proper voltage and pressure. Though haven't noticed a big difference with the new filter. The check engine light cycles a code of 21, which is refinanced to the O2 sensor, both upstream and down stream. That tells me that there are TWO O2 sensors for this model. And research has confirmed this. One ahead of the cat and one behind the cat.
Here's the kicker, I only have one O2 sensor at the head of the cat and the location of where the second one would be located is only a solid section of pipe from cat to muffler. I haven't been able to track down the plug connection for the second sensor and these codes and problem only came after I gave the Jeep a tune up.
1994 Jeep Grand Cherokee Limited V8
View 5 Replies
The check engine light on my 1997 Integra (LS, 119K miles) has come on for the second time. Including background below.
Incident #1: Carin mid-June, the car sputtered or shook a bit when starting and the check engine light came on.The car had been sitting in the garage only about a day. Codes were P0303 (Cyl 3), 0304 (Cyl 4), P1399 (multiple misfire), P1300 (random Cyl misfiring). The p0303 code set at 1600 rpm & at 75F degrees. Misfire code set during warm-up. The shop performed block test (came negative). Compression tests show 1, 2, 4 at 200 psi & 3 at 190 psi. The shop replaced spark plugs & inspected plug wires & connectors as well. Valve clearance adjustments also were done. The shop cleared the engine light code.
Incident #2: Last week (early Aug), the car again sputtered & shook when trying to start (had been sitting in the garage for about 2.5 days). Showed signs of low or dead battery but started after cranking a few times. The check engine light came on again. Codes (checked at home using the jump method) indicate Cyl 1 & 3 misfire.
Will be taking to the shop for the diagnosis again but wondering if it is battery or ignition related; shop doesn't suspect the battery, however, I do sense that the battery 'feels' weak esp. when starting. New battery put in May. What could be going on?
View 6 Replies
I am having a “Check Engine” light problem on a stock 06, 4 cylinder Jeep Wrangler with manual transmission. A local highly regarded independent mechanic has had it in his shop 3 or 4 times for more than a day each time. On the first visit he replaced a purge solenoid valve and reset the light. It stayed off for more than 400 miles and then relit. He went over it and checked the wires and connections and reset the light. Again it stayed off for some time and then relit. He has checked the Jeep site.
After the last visit he suggested I drive it and see if it would reset itself as it had been doing in the past. It did reset itself twice but it only stayed off for 10 miles the first time and 2 the second. The code indicates an electrical problem and he is now planning to drop the fuel tank and check the wires and sensors there. The next step may be an ECM transplant. This is only an emission system problem and the mechanic says it is OK to drive. We do not have emission inspections here. How important is it to fix the problem?
View 4 Replies
I have a 2001.5 passat and the check engine light turned on. It just so happens that whenever i put gas in the car.... and try to start it back up, it won't start! it takes about 3 or 4 tries for it to start up.
View 3 Replies
Bought an R32 yesterday. used of course.. was doing fine feels like a brand new clutch. got it from a ford dealership, and the check engine light just turned on. I will go back for the 14 day policy but i was wondering if it could be my clutch.
View 8 Replies
I have a 2006 Sonata. My check engine light came on and also my ESC light. My car does not accelerate. It takes literally about 40 seconds to get up to 20 miles an hour. I called the hyundai 800 number and they said there is a recall for a "stop lamp switch malfunction".
View 3 Replies
I have a '98 For Ranger. After 256,000 miles, I recently had a new (rebuilt) motor put in my truck. After about 2 days of driving with the new engine, the Check Engine light came on. I went to Auto Zone and had the codes checked, and these two codes came up:
"Misfire monitor malfunction"
"Oxygen circuit slow response bank 2 sensor 1"
The guy at Auto Zone couldn't tell me what they meant. Is this something serious that needs to be checked out immediately or have anything to do with the new motor that was put in?
View 3 Replies
My check engine light just turned on recently. Just hit 115K miles on my SC430 a few weeks ago. Is there a service that I'm missing? Running absolutely fine, oil change recently as well.
View 14 Replies
'95 LeSabre, 250K, runs great. Check engine light on randomly and signs point to a computer malfunction causing the light to come on. Is it true that only a dealership can replace the computer, not an indy mechanic? How much for the repair? Will it run ok w/o a new computer?
View 6 Replies
My check engine light came on at 102,000 miles. The dealer service dept. says that the diagnostic showed no clear cause(?)but I need new spark plugs ($240),ejectors cleaned, and of course the cost of the diagnostic ($130) The total was around $475. Am I being ripped?? My big question is what will they do to get the light out?? Should I disconnect the battery and reset the clock and radio buttons to see if it goes out? Then I can worry again if it comes back on.
View 30 Replies
I have a Hyundai Elantra 2007 with 123,000 miles on it. Three weeks ago the engine About two weeks ago the engine light turned on. I took it into an auto parts store so they could use the digital code reader, it said the upstream O2 sensor needed to be replaced. I replace it and still have bad gas mileage, the second time I had it read with the code read it said both of the O2 sensors were bad so I replaced the downstream one week later. There was still bad gas mileage and the code reader still said it was both of the O2 sensors, the auto part's representative said when the engine light is on that the computer turns off the O2 sensors so he recommended to erase the codes on my car with the code reader (I pushed the button and he looked away). Still nothing changed so I disconnected the negative terminal on the battery to restart the computer. Still horrible gas mileage with no engine light anymore. Gas mileage averages about 15 mpgs in city and 32-35 on the highway. The highway seems about right but I've never seen any mpg below 30 for city mpg before this problem. I also cleaned the mass air flow sensor with mass air flow cleaner after dealing with the O2 sensor. All preventive maintenance is kept up by me and I have had no problems with this car before. Water pump replacement, timing belt replacement, and transmission flush have occurred in the last ~50,000 miles.
View 19 Replies
My mother in-law has a 94 Chrysler LHS, 3.5 V6, auto, 66k. Yesterday she was driving home and said the check engine light was on. I went to check it out and the light was not on. The light come on when the key is turned on but goes out when it is started. This is not an OBD-2 car it has a little blue plug and i do not have a code reader for it. Took it to auto zone and they do not have a code reader for this car. Auto Zone and Pep Boys both told me that if the light is off there will not be a code. Further checking on the internet I found out you can get a two digit code by turning the key on and off and count the flashing check engine light. It worked I got code 12 and 51. 51 means lean O2 sensor. If this is true that why does the CEL not stay on. How can I test the O2 sensors?
View 2 Replies
Check engine light issue. For the past 3 months, my check engine light has been turning on. The first time it happened, the garage replaced the EVAP Purge Solenoid (which includes the vapor can purge solenoid and the EVAP canister purge solenoid). Of course, a few months later, the check engine light turned on again. The second time, the garage replaced the gas cap. Then the check engine light turned on again the next day.
So, the third time, the garage performed maintenance/repair on the vapor can purge solenoid and the EVAP canister purge solenoid. Of course, three days after driving my car, the check engine light turned back on. I've contacted the garage for the fourth time now. I explained that their diagnostics have obviously been exhausted, and they aren't really sure what the problem is. I'm going back in a few days to speak to the lead mechanic hoping to be compensated for their guess-work or at the least to be given an honest "I don't know" answer.
View 7 Replies
I have a 2001 Ford F-150 v6 2wd. A few weeks ago, the check engine light turned on so I drove to the nearest autozone to hook up their computer and see what the error code was. The technician gave me the code (I don't remember it off the top of my head but it wasn't something imminent). Before leaving, I asked him if he could clear the light, figuring that if it didn't come back on after 50 miles, that it might have just been a fluke with one of the truck's sensors. Later that day, I realized that when I started the truck, the check engine light was no longer turning on momentarily the way that all the dashboard lights do to tell you that they're working.
I went back to a different autozone (one closer to my house) and explained the situation. They checked the computer for codes again and found none and said that the light must not be turning on because the bulb is burned out. I find this to be a striking coincidence that the bulb should happen to blow out exactly when the technician used his computer to clear the light. Is it possible that he did something with his computer that permanently disabled the check engine light? It's been a few weeks and I've since bought an inexpensive bluetooth code reader of my own, hooked it up, and found that there is still no active code. Is it possible that the code has returned or will return, but that I won't have a way to know because something he did suppressed not just the light but my car's code reporting mechanism?
For now, the truck drives fine, but I'm afraid to travel long distances when there might be a problem I don't know about.
View 7 Replies
