I just found a nice Prius C for sale with little damage to the front right corner, no frame damage or anything, just some bodywork needed. So, after it was fixed up. I brought the car back and there is weird issue that I have - turn signals and Hazard lights dont work. When I turn it on, i can hear clicks from it, but I dont see lights blinking on the dashboard and my head/tail lights dont blink as well.
View 5 RepliesI have a no spark no fuel situation. But my check engine light does not come on and my clock does not work. My turn signals dont work on the dash and the bulbs. But my hazerds work fine. 1997 yukon 5.7L...
View 7 RepliesI have had this problem for a while now, but can't seem to figure it out. I'm sure it's an electrical issue, but I'm not that great with electrical. My turn signals don't click when I push the handle in either direction. The turn signals come on and stay on but don't blink like they should. I checked the lights in the front and back and they just stay on but don't blink. Also my hazards don't blink. They just stay on and don't make clicking noise either. My horn doesn't work and my door doesn't ding with the key still in the ignition but in the off position. I don't know of it's all related or different issues.
View 10 RepliesHow to fix or solve front turn signals that are not working? I just realized that both the front signals on my Prius doesn't light or flash when making a turn, the rear are working fine. Is this an easy fix or should I bring it to the dealer?
View 4 RepliesI just bought a 98 passat sedan v6 four days ago. When I purchased it the turn signals and hazards were working. I was driving yesterday and they went out all of the sudden. Thought it was the fuse at first, changed it, still not working. I bought a turn signal flasher relay, but the repair manual doesn't tell me which one it is so I can change it.
View 2 RepliesRecently my Infiniti G20's turn signals and hazard lights stopped working. I replaced the flasher relay and turn signal switch but it did not solve the problem. Here is the kicker or clue. The lights flash when locking or unlocking the car with the remote FOB.
View 7 RepliesCar is 2000 Corolla with 58k miles. Today, I had my hazard signals on while parked when suddenly....they stopped blinking. The signal lights in the dash just stay on...they do not blink. I also verified that both front and rear lights also turns on...it just doesn't blink.
The corolla has a fuse box under the hood in the drivers side. Here is the schematic for the fusebox: [URL] .....
From what little I know about mechanics/electricity, can I just pull the wiper fuse and put it into the turn signal fuse while I wait for a new fuse? Do I need to disconnect the battery?
How to confirm this is the part I'm suppose to install: [URL] ....
I have had an ongoing issue with my 2010 Santa Fe Limited with the battery randomly being drawn down and would not start the vehicle.
I saw a post somewhere on the internet to remove the Negative connection on the fender and grind it down to the bare metal so that it has a good ground connection.
I have done that last week, but last night before turning in for the night i looked out the window and saw lights in my driveway. I went out to investigate and found that the Santa Fe's turn signal/hazard lights were all on front and back and not flashing.
I got in the vehicle and turned the lights on and off with no keys and they all went out.
I got the schematics for the Santa Fe and i believe it could be the Hazard relay that seems to be located inside the I/P Junction box or could be the Hazard Relay Control in the BCM.
I have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?
View 2 RepliesI have a 2006 F250 Superduty 4x4 that the brake lights hazards and turn signals have stopped working in the rear.. The middle cab brake light does not work either.. The running lights do work as well as the turn signal and all lights in the front.. I also checked the trailer plugs and both work for running brake and signal lights.. I have checked all fuses under the hood as well under the dash with a test light and i have nothing blown.. I have replaced the Brake switch as well as the flasher module under the dash and picked up a new multifunction switch (Turn signal/hazard) and that didn't work either.. I'm stumped at this point.. I have not checked the bulbs yet but wouldn't think they would all blow at the same time.. (will do this next)..
View 3 RepliesMy 2007 F150's turn signals and hazard lights quit working. I checked the fuse and it was blown. Once I pulled the old fuse out the truck wouldn't start at all. What happened?
View 3 RepliesI was adding some more running lights today and tried to tie in to the front running/turn signal light. Next thing I know I hear a pop and now no turn signals, hazards or brake lights on my 99 F250 SD V10. My 3rd (center) brake light does work though when I press the brake, it's just the tail brake lights that dont work.
I can't find a blown fuse for the turn signals or brake lights (not really sure which fuse box it's in since the manual doesn't tell me what fuse is what)
I however did find what I'm guessing are the flashers behind the radio. What might have went wrong where before I start dumping money in to flashers and relays.
The next question is, can I jump in to the marker/turn signals and add another single LED light to them off the front? If I can which color wire does what?
Recently, I lost function of brake lights, turn signals, and hazard flashers. All happened at the same time. Some threads discuss flasher relays, short steering column wiring (position of steering wheel), and fuse failures.
I checked #18 fuse and a few others. All had continuity. I assumed my bulbs were all good. My hazard push-pull switch did not feel right. There didn't seem to be engagement. At this point, there was a good chance that the multi-function column switch had failed so I decided to try replacing it. I'm happy to report that this switch was the cause of all the light function failures and now, all is well again.
Removal is done by prying the key lock switch cover off,, removing three 1" Philips head screws that attach the lower column shield to the upper shield. At that point the upper shield can be completely removed. The lower shield was not totally removed because the tilt lever was left on. The switch is attached to the column with two 3/4" Torx 20 fasteners. The upper is easily accessible and the lower fastener can be removed by pulling the lower column shield down so access can be achieved. The two wiring harnesses have a conventional harness lock to depress and the connectors pull outward from the switch. Installation is the reverse of removal, noting the dowel locator and small plastic dowel on the lower shield.
1994 Econoline E350. All the other lights work but on the front right the turn signal light flashes but the Hazard lite will not flash. I check for power at the wire at the light and there is none.
View 6 RepliesThe turn signals/hazard flasher on my 99 Sebring Jxi stopped working a couple of weeks ago. When I use the signal lever or press the hazard flasher switch, you don't hear any click of the flasher relay, and the lights (front and rear, and on the dash) don't light up at all.
So far, I have:
* Checked the fuse
* Replaced the flasher
* Replaced the turn signal switch
* Replaced the flasher AGAIN (mechanic says that if there was a problem with the turn signal switch, it can burn out the flasher)
* Checked the fuse AGAIN, and even replaced it (even though it's the same fuse for the wiper/washer, and that's still working)
I asked my mechanic about it, and he said that a bad ground can also cause problems. The big question is: where do I begin to look?
I have a 2003 V10 Excursion with an electrical problem. The right turn, right brake and right hazard light do not work but the flasher makes the clicking noise. When the right turn signal is on, the right front turn signal light works but is at double speed. The right rear light does not work. Same when brake and hazard are applied.
I checked the bulb socket with a multi meter and have no current. I also checked my trailer plug and have all functions work. Fuses were checked also for the brake circuit and were all ok.
I have a chevrolet optra 2007 and the hazard lights won't work unless the turn signal (left or right) is switched on at the same time. Turn signals work perfectly fine.
View 7 RepliesThe right turn signal on my 1998 Ford Explorer recently stopped working. The flasher was making a horrible buzzing sound when I tried to signal right, but worked fine signaling left.
I just replaced the flasher, which has cleared up the buzzing noise when trying to signal right. The flasher clicks like it's supposed to, but the lights still do not flash.
Here's a summary of the current symptoms:
-Hazard lights work fineFlasher clicks; interior indicators flash; exterior lights flash
-Left right signal indicator works fineFlasher clicks; interior indicators flash; exterior lights flash
-Right turn signal does not work
-Flasher clicks
-Interior indicator stash off; exterior lights stay off
What to check next???
I just got a 2000 F350 cc drw 7.3l.
I did search but have had no luck. My turn signals do not work, unless my foot is on the brake pedal my green arrow indicator wont even turn on. When they do my bulbs work but don't cycle so I know all the bulbs are good as I had my wife check all four corners when I got them to come on for a split second. I have tried replacing the MFS and the turn signal relay under the radio in the dash.... When I do turn on my blinkers I can hear the relay click once but that is it, no more.
I tried checking the wiring in the column and tilting the column to its extremes while trying to engage the turn signals. Also, if I unplug the brake light switch then I do not get an arrow on the IC to light up so I am guessing the power flows through that switch. I don't have a chilton manual yet and the owners manual was not in the truck. I did check fuse 23 ?
I have a 2003 Chevy Malibu - periodically, they turns signals decide not to work. I don't know that one thing in particular causes them not to work. What could be the issue and is this something I can fix easily (I'm a novice), cheaply and quickly myself?
View 2 RepliesToday, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.