Fearing the worse here on my 2011 Prius Four, not IV. When I press the "on" A/C button I hear a grinding noise for about two seconds. Seems to be coming from a low area in engine.
View 15 RepliesI've got a new issue that is happening on the front end of my truck. Whenever I try turning my wheel while driving, I get this rubbing/grinding noise coming from the front of my truck. It only happens when the wheels are in motion. It seems to happen less when I'm driving at higher speeds, but I can notice it make the sound at any speed. I tried driving it slowly in an empty parking lot while turning and it's definitely making the sound every time the tires rotate.
I took it in for an alignment because this was happening every time I drove, whether it be driving straight or making a turn. Now that my alignment has been fixed, it no longer make this noise if I am driving in a straight line, so it only seems to happen when I'm turning. I had the mechanic check to see if they could reproduce the issue. The mechanic was able to hear what I hear, but when he put it on the lift at the shop, he was not able to reproduce the sound.
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
Just purchased a used 2008 prius with 80,000 miles on it. Braking system makes slight grinding noises when getting below around 10mph. I know the brakes are different, so I'm not sure if this is normal or if it means my brake pads need replacing? Car didn't come with an owners manual .
View 6 RepliesI have a 2001 Ford F-250 with the gas v-10. Yesterday it started just fine as always. Today I get into it and it starts to turn over just fine then starts to make a grinding sound and the truck won't start. I have had a fuel issue in the mornings with once it started you had to barely press the gass to keep it running. But never makes a funny sound and always runs fine. This only last for a couple of min and then it runs fine for the rest of the day. The grinding is not the starter. I took it off and had it checked and it was fine.
The truck had been using oil. When I checked the oil level it was low but it was still on the stick. "I know a motor needs oil to run smooth but it's my dads truck and well let's just say he is not the best on maintenance". Also I smelled the oil and it does have a gas smell to it. So it definitely does have some gas in the oil. I tried to light the dipstick with a lighter and it wouldn't light. So not sure how much gas is in it but that's what I did.
So the question is, would something just in mid crank go bad and then not let the motor crank. Truck made no weird noises before this so I find it hard to believe the barrings just went out in mid crank and now it is shot.
Also I just checked compression on front cylinders.
Driver side read 75lbs
passenger side read 100lbs
My car just started making a grinding noise when accelerating. It does not make it while maintaining a constant speed or revving the engine in neutral. I never had this problem before and I am at a loss to explain it. Car is 1995 Camry for what that is worth.
View 4 Replies01 Passat v6 150K tiptronic. When cold, the tranny makes an occasional grinding noise however when at operating temp it runs fine with no slippage. Changed the fluid/filter and added lucas treatment. It worked a little but my mech said to warm up the car before driving. Might be the torque converter?
View 3 RepliesShould I hear my Touareg wind down everytime I shut it off? Almost sounds like an airplane coming to a stop but its not that loud.
View 3 RepliesI have had this problem since day one. The idle seems to be very rough once you give it some gas and drive the car it runs smooth as silk. The dealer told me that is the wayit should be due to the narrow V6 with one head cylinder. I have had an 02 Passat V6 and I dont remember it having a rough idle.
My other issue is again since day one when I am moving very slow like when I am backing out of my drive way there is what I would describe as a grinding sound. It does it all the time forwards and back, all day not just the first thing in the morning. Again the dealer says it is normal.
I just had my first oil change about 2 weeks ago and was hoping these were just thing that would be addressed then but they dont seem to be better or worse always the same.
1950 cadillac - standard drums on all 4 corners.
I put new wheel cylinders on each drum, and replaced the drivers front hose, as it was clogged. The passenger side I left because it works and doesnt leak. I've cleaned all the brake surfaces, shoes and drums, and bled everything.
When I brake, and only when I brake, the front right makes a grinding noise and the car pulls to the right.
I tried tightening the star wheel today to bring the shoes inward in hopes that would equalize brake pressure up front, but when trying again today, I got that grinding sound still.
There is no scoring or gouges on the shoes, drum, and the inner and outer ball bearings seem fine - round chrome balls with no discoloration, no gouges on the spindles. Granted I don't drive this far at all, especially now that I have this grinding.
How can I really tell if its the ball bearings? It only makes the grind when I am on the brakes.
Changing wheel bearing on mk4. makes noise when i turn to the right. what side is bad? i like working on my own car but this might be out of my hands.
View 12 RepliesI have a 2003 f150 4X4. Whenever I go around a round about slowly, the truck sort of grind under the frame and shakes a little bit like I am in 4 wheel drive.
View 2 RepliesOn my xl-7 upon turning left it makes a poppping noise, its real bad at complete stops,its almost like a cv axle noise. Ive taken it to the dealer at least 8 times and they replaced struts , but it still makes this noise.I also called the main Suzuki customer office and complained. They told me its just one of the characteristics of the new Xl7.
View 4 RepliesI have a power steering pump that makes a moaning noise when turning. Normally this means your fluid is low, but mine is full. Is it possible the reservoir is clogged not allowing fluid into the pump? When you take the cover off the reservoir the fluid is frothy so you know the pump is cavitating.
View 4 RepliesHere's my problem, I have a B5.5 1.8 5speed and my power steering makes a whining noise when Im turning. I checked the fluid and it's full. A few years ago on a roadtrip from CA to NM, my PS cooler hard pipe had a leak and drained all the fluid. It's was 11pm and still had 30 miles to get home and all I could get was Pennzoil PS fluid from Walgreens. So for the past 3 years I've been using Pennzoil PS fluid. Just recently it started making this noise. Luckily I picked up a 98 AEB parts car for $300 and my question is,
Would a power steering pump from my B5 fit my B5.5??? And, If the problem isn't my pump, would the PS rack fit also??
Recently had this problem which started up about a week ago where my car would make this clicking noise whenever I turn left while driving. When I turn to the right there is no noise. Some said that it could be that CV joints need to be replaced. I have a video showing the side that is making the sound, maybe there is something abnormal that I don't see.
[URL]
I've recently replaced the power steering pulleys and belts. Now when i turn car, it makes a clunking /clicking noise and sometimes the power steering tugs back a bit. 2010 camry.
View 3 RepliesI have a 2008 Elantra with 59,000 miles. When it is warm out (70 F+), the sterering wheel makes a binding noise (squeeking noise - it is hard to describe) when turning. It doesn't do this all the time and it is much more noticeable when it is warm out. The temps are usually mild. This is a recent problem as I haven't noticed it before.
Should I be concerned about this? I want to get it checked before the 60,000 mile mark in case this is a serious issue such as rack and pinion steering problems.
I have a 2007 ford edge that when you turn left or right it sounds like the traction control is activating and makes a ratcheting noise. I have replaced cv joints and wheel bearings.
View 4 RepliesI am in the process of replacing the front hub seals so my ESOF works again. I tested both front hubs with a mityvac and neither one of them holds any vacuum at all. All the lines are good, and the pump and solenoid seem to be working fine.
I have the driver's side apart and I have a couple of questions.
What's a good source for the vacuum seal? I've checked rockauto, riff raff, and diesel o-rings. Diesel o-rings has it, but the description says it's only for 2003+ Excursions so I didn't order it.
There is no yellow o-ring anywhere on the hub. I assume that someone forgot to put this o-ring back in and this is why I don't have ESOF? I guess what I really want to know is that there isn't some 2000-specific thing where there's no o-ring, right?
After I got the hub off, I spun it around on my workbench and it doesn't sound good at all. It makes a slight metallic grinding noise about 1/2 way around. I assume this isn't normal? AFAIK these are all original parts - but the missing o-ring means to me that someone already had it apart.
There was a lot of water intrusion and rusty colored grease but nothing was dry, the needle bearings were intact and the shaft isn't scored at all where the bearing rides. I'm hoping new seals and good cleaning and it should be good as new. And then it's off to the next side.