I have a 2014 Prius C and for the last month or so it's sometimes difficult to shift from P. I always park car with handbrake. It's specially difficult if I push down hand brake before stepping on the brakes and car shifts a little while on park. Car has 35,000km.
View 9 RepliesMy 2004 Explorer XLT 4.6L V8 AT is very difficult to shift out of park. Sometimes I have to push very hard on the brake in order to get the transmission selector out of park. Other times it is no problem.
View 1 RepliesI recently had a spin out on the ice in my 2001 Honda Oddessy Minivan and had to have the back wheel and front rim replaced. I definitely hit the sidewalk at least once and ended up backward in traffic with the back of my van on the sidewalk. Just after getting the work done I noticed for the first time that my car was having trouble shifting out of park into any other gear when starting and when I had it running but put it in park. I have to either press the brake several times, all the way into the floor to get it to shift out of park or pump it once or twice quickly and when I hear a little click, shift it into gear. Is this a transmission problem? Could it have been caused by my spin out?
View 3 RepliesI have a 04 W12 that is having trouble recognizing that it is in park. when i shut the car off and go to remove the key it says please place in park. i purchased a known electrical gremlin car so i am chalking it up to that but should probably fix it. it also does not detect the speed the car is traveling so no digital speedo/ accompanying readings. other than that it is pretty solid. haven't noticed any other "glitches" the park problem is new started yesterday. i have had the car for 2+ months and love it. i have been looking for a W12 for some time now. a
View 5 Replies2009 F150 4wd.. I have no - power windows, door locks, radio, blinkers, will not shift out of park, no dome lights. all started last night after it was parked for about an hour the lights flashed on their own and when I went to leave this morning all of this is going on. I have :
- checked fuses - good
- checked for codes - none
Truck runs fine, you have to press the shift lock button to get it out of park,runs like normal.
I have a 2010 Lariat and it randomly gives me fits by not letting me shift out of park. This started yesterday and I want to know where to start looking so I don't get stranded in BFE! Its a center console shifter.
View 2 RepliesSo I drove my F150 to work as always, with no problems. I went to leave and it fired right up, but it wouldn't shift out of park. The emergency brake light was on even though the brake was not applied, the traction control light was on even though I wasn't moving, and the tire pressure warning light was on even though all tires are new and inflated properly. I removed the cables from the battery and brushed the contacts even though there was no grime on them, and when I went to start it, it just kept cranking without turning over. So I turned it to off and gave it one more shot and it fired right up, and drove like it was perfectly fine. Why this happened? I got 75k miles on it and have never had a problem...
View 6 RepliesI had a clutch, slave cylinder, and master cylinder replaced about 20,000 miles ago. Everything seemed to be working fine until I drove across the Rockies. The transmission was extremely difficult to shift, and the vehicle would actually roll forward when cranking the engine at fuel stops (temps were minus twenties). Once I got out of the mountains on both ends of the trip (where it was warmer), the clutch worked normally. The local Ford dealer found lots of air in the hydraulic clutch system, bled it, and it worked fine for several months.
The clutch is doing the same thing currently, but not all the time. Some days it's fine, other days it's difficult to shift although double clutching seems to work. It gets particularly hard to shift after a long drive (e.g., interstate driving for a couple of hours). I took it back in this morning to see if the dealer could figure out what is going on, they're saying it's likely a bad slave cylinder. I've heard the 1995 Explorer clutches are a bear to properly bleed, and can't work but think there may still be some air in the system.
My son has a 2008 Ranger 4.0 4wd 5 speed. Every month or so we need to bleed the clutch as the transmission becomes very difficult to shift. It does not lose fluid, but seems to be holding air. And it's not easy to bleed this setup. Slave going bad? I guess the transmission will need to come out then.
View 3 RepliesOn my 2002 sometimes when I come to a stop after rolling around with the ICE off, then right after I shift in Park the ICE starts up. Why would it do that? Is this a bug or is it normal?
View 16 Replies2nd time I've had this problem. With the car turned on "ready light" on, the car will not shift into D. It just stays in park, and yes my foot is on the brake. I've tried to reset by turning the car off, turning it on again and shifting into D, still no luck. By retrying this over and over it finally goes into Drive and away I go. I've had the car for 3months and 5k miles, and this has only happened twice.
The second time occurred when I was stopped by a flagman at a road construction site. Instead of shutting down, I just pushed the park button. The lights were on, the radio playing and my garmin was plugged in and the AC was on, would the high load have caused the problem? When I pulled the plug on the Garmin, the car went into gear on the next try, but I don't know if there is a cause and effect. I finally got it going after about 25 cars had to go around me and the last car was passing me when it finally went into D.
I was successfully able to install my Prius backup camera, but a few hours later I found that I could not shift out park. I was getting code U0293 on my scangauge. I can push the override button next to the shifter to shift out of park, but I can't figure out whats going on.
View 6 RepliesWhen I start the car and get the Ready light, I try to shift into P or R, or anything, it doesn't shift. Then it beeps once. I've tried turning everything off. Exiting, locking, unlocking and retrying.
I get the Ready light and the gas engine even starts, it just won't shift. But beeps once after I try to shift into any gear.
I am replacing the rear passenger hub assembly and as soon as i put a significant amount of torque to the axle nut...i get a crazy grinding noise and the hub becomes very difficult to turn. When I disassembled the old assembly it took very little effort to push the axle freely in the splines of the hub after i took the 32mm nut off. Now when i start to get the grinding, i remove the axle nut and it take some serious whacks with a larger hammer and brass drift to free the axle spline in the hub.
Ive dug around online and found someone that had to slip a couple pieces of wood in between the sheet metal dust shield and the end of the axle to fully seat it.
1992 Buick Park Avenue, Base. For awhile now I've had trouble shifting into park from other gears. Sometimes, it'll flow right into park without trouble. Other times, I have to work it, to kind of baby it in. However, it simply will not shift into park from reverse. Period. If I'm in reverse and want to park, I have to go into drive, neutral, etc, and then try to move it into park.
A mechanic I know looked at the neutral safety switch and thought it could be causing the problem. We figured it wasn't in the steering column or the cable to the switch because if we disconnect the cable, you can slide that lever all day long. So I purchased a new neutral safety switch and had him install it, but the same problem is there. Actually, let me clarify: while it was in his garage, with the old switch, it would no longer go into park at all, regardless (kind of decided to just stop altogether). At least with the new switch we can baby it into park, but it is basically back to where it was last week. He mentioned it might be deeper in the transmission, but that's out of his league.
I have just bought a 2001 Prius with 127,550 miles. Hybrid battery has been replaced with a used one and all systems seem to work fine except the shift lever in the "Park" position does not lock the transmission. No big problem as long as the Parking Brake works. Preliminary investigation does not reveal any easy fix.
View 6 RepliesWife was driving 2008 w/70k miles, powered off completely in middle of street, coasted into parking lot. No warnings or lights on dash. Unable to shift to park. Won't power on to acc mode even. Interior lights etc work fine. Battery measures 13.6, 14.2 at front terminals? Slight burning smell from engine compartment possibly right side. Disconnected battery for hard reboot, no change. Unable to read codes as won't power on.
View 19 RepliesToday, I was parking the '05 Prius and noticed the gear shift stuck in the drive position instead of the usual "pop back" you experience when you put it in drive. The park button woud not engage. The same thing happens in reverse.
The dealer said they have had to replace the gear shift on a bunch of cars with this sticky gear shift problem.
Everything was working fine until I started messing with camera settings in the service menu today . Now when I shift into reverse, it says "system not ready". Will not let me parallel park or reverse park now. I tried to reset the settings but maybe I don't know how to "save" settings.
View 5 RepliesToday, without explanation the shift indicator on the dash on my 98 Passat Wagon highlights all gears. When you shift to any gear. . . . the display does not change. Further, shifting is rough from 'park.'
I noticed this problem after looking at all the fuses to see why the radio was not powering up. I have checked fuses. . . . and unplugged the battery and plugged it back in.
I have a 2013 Prius C 4. If you try to manually enter destination addresses in the system, it's quite quirky and non-intuitive. It can take a number of minutes to enter in an address, and the system will often offer up suggestions about what it thinks you're entering that are incorrect. If you don't enter the fields in a certain order, such as Street number first, then street name, then city, it may not display the right options you need to complete the address.
View 19 Replies