Prius (2004-09) :: How To Install Front License Plate
Jul 18, 2015
had a couple questions about installing the front license plate. I currently do not have any holes drilled in the front bumper (though I can see the places where they are supposed to go). I have the black plastic attachment. What is the best way to drill those holes? Can it be done if I don't have a drill (i.e., just with a screwdriver and force)? Is this something the dealer might do for free (I don't have a warranty, bought my car used)?
View 9 Replies
Advertisement
License plate light comes on when any door opens? it fades out a little after it's shut. stays on for a minute or so. (like interior lights would if i had the door dome switch on).
Any way to turn this license plate light off for this function? stays on if the hatch is open, or any door. I car camp a lot and crack the hatch for air. license plate light stays on.
Also the lower door lights, when they are individually open. I'd like them to not come on. Yes I could just remove those bulbs.
I had installed led lights on the whole car/ every bulb inside and out. even fog lights. i didn't replace the hid headlights, though I'd like to.
View 11 Replies
I need to mount a plate on front bumper and there are dimples for 2 holes. Do I just use self tapping screws here as I've read you don't need a mounting frame?
View 3 Replies
Mounting front license plate somewhere other than the "official" mounting location? I don't like the thought of putting holes in my front bumper. I can move it down a bit such that the holes are in the bumper just above the air opening. So, they would be less noticeable. This would block some of the airflow through the lower opening. But, unless I'm driving in 100+ deg temps, it probably won't matter.
I could also offset it to the right or left in the lower opening.
View 14 Replies
After going through the car wash several times now in my 2010 RX 350, my front license plate has been bent in all different directions. Car wash guys say it's due to not having a full plate holder, where as 4 screws secure the plate vs. only the top 2 as we have. Any plate holder from another vehicle that I might adapt to overcome this?
View 14 Replies
I plan to remove the front license holder from my car, fill the holes, and paint/clear coat/sand them. Any recommendation as to what to fill the holes with (I'm not going to use a plug.) Exactly what the bumper cover is made of, I can find the right material to bond to it.
View 2 Replies
How do I get rid of license plate holes on my front bumper? I took my front plate off and now I am stuck with annoying holes drilled into my front bumper. Its not noticeable but i know its there so it irritates me.
View 4 Replies
Ok, Im trying to get my front licence plate holder off. I've looked in all the DIY forums and cant find what im looking for. My question is how do i get this thing off?? I've took the two screws that hold the thing to the bumper off, and its still soild as before i took the screws out. Is it held on by the rub strip?
View 24 Replies
I have a 2010 RX450h and live in Minnesota where it is hard to hand wash my car. The darn car washes tend to catch the front of my license plate frame and bend it and the license. I have tried several different plate frames and none worked. Minnesota plates are now the thin, non-stamped plates so they are very flimsy.
I even tried putting a plastic plate behind the license to make it more rigid but that failed too.
View 1 Replies
yesterday I got the idea to move the plate bracket on the front all the way down so it gives it a much cleaner look and doesn't obstruct the grille. To do so test mount the bracket on the lowest position, then have someone hold it. Then you take a 1/8 drill bit and make the two new wholes then put everything back together.
View 8 Replies
replacing the entire front bumper.I have removed the front license plate holder, and would like to fill the holes where it was screwed into the front bumper.
View 8 Replies
I'm in the process of replacing license plate bulbs. I broke the old housing for one of the bulbs so I bought new LED lights on eBay and they came with the housing. The problem is, I can't get the cover to stay clipped in to the tailgate. How to get the lights to stay in? What am I doing wrong?
View 7 Replies
I try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 Replies
I am trying to swap out my stock license plate bulbs on a 2012 Prius.
After getting to the bulb socket holding thing, I have read that you're supposed to turn it 1/4 counterclockwise and pull but mine is stuck and won't turn either way.
View 7 Replies
No tail, turn, backup, flasher, license plate - NOTHING. i checked fuses - cleaned both connectors under the truck by drivers door, cleaned connectors by the spare tire (2) one large one and one small round, the cleaned ground lug on top of spare tire bracket, all bulbs are new. cleaned with LPS contact cleaner, they were new and shiny and reinstalled. NOW - turn is very weak and when i push on brake they go off and the front blinkers blink twice as fast? I a aircraft technician and know my way with an ohm meter but totally stumped.
View 8 Replies
How to change license plate bulbs? The little clear covers dont seem to pop off ........
View 3 Replies
Was trying to remove the licenses plate screws today. One comes out easily, the other won't budge. I've sprayed a couple of times with WD40 but its still stuck.
View 14 Replies
So I bought LED license plate lights, the same ones Track5tar has (who sent me the link to get them). I got em off the bay, and I put them in and they don't work! The Heatsink gets hot but the lights don't light up in both of them!
View 24 Replies
So I was replacing the lights with the new leds change one toke some pics to compare. Everything fine...
Removed the other feston put the new led and they won't turn on anymore..
Change them back. Put them upside down, up, sideways... Nothing
Check all three fuse boxes all ok
Every other light on, inside trunk on, side markers on...
Everything but the license plate lights.
View 12 Replies
Bulbs are fine, I turned the light switch from off to on (12 o'clock position) and they flicker for a split second. What can be wrong? I checked the harness on the rear hatch and it looks fine. Maybe the switch itself?
View 2 Replies
So I took my GTI in for my 10k service and to have them fix the wastegate rattle and the subframe shifting. They fixed the wastegate by installing the clip but didn't have the shims in stock for the subframe so I need to go back anyway, but I'd really like to fix my license plate lights before then.
Is there a possibility the tech could have accidentally unplugged a cable for the lights when he was rotating the tires or messing with the wastegate, etc? Maybe a blown fuse? I'm running LEDs and I already tried putting the incandescent bulbs back in but they don't work either.
View 5 Replies