Prius (2004-09) :: Turn Off Intermittent Beeping When Red Triangle Lights Up?
Jul 31, 2014
I have a 2007 Prius 5 with 205,000 miles. Just recently, while Im driving the Red Triangle blinks on intermittently along with an annoying beeping. I took to dealer and they diagnosed error code C1300 which indicated that I needed a new "Brake actuator assembly with skid control ECU". I declined price tag because they said it's nothing critical (despite that it sounds rather important), and car will run fine without replacing this part. However, they said "nothing we can do about the intermittent red triangle and beeping".
Is this true? It's a very annoying noise. I know that it is possible to turn off the reverse beeping. Isn't there a fuse associated with "beeping" that could simply be disconnected?
View 8 Replies
Advertisement
I have a 2006 with 106K miles. Noticed after making a sharp left turn in a parking lot that the Red Triangle came on along with a beep and the message, "Problem" on the touch screen. Started happening more frequently either when the wheel is turning left or if I'm driving straight and the car drifts a little towards the left if I'm on the highway. Today it happened about 6 times. Warning goes off after a couple of seconds.
View 9 Replies
Just got a diagnostic from the nice people at Prius Battery Repair. Check engine light was on and intermittent red triangle when I make a left turn. Code PO505 came up- Idle control System. I have 162,000 miles and just put in a reconditioned battery that checks out fine.
View 5 Replies
I have a 2007 Prius which now has 164,000 miles on it. Never had ANY issues. Just this past week, I was riding with my husband driving, and when he downshifts into "B" gear and turns to the left, the triangle of death flashes on the screen, a loud beeping occurs, and on the top of the main info screen the word "Problem" appears. I want to make an appointment to take it to my dealer, but they aren't too sharp and might tell me I'm nuts. I'm not.
View 3 Replies
Our '06 has 68K on it. Last weekend I changed the front bumper (just cracked from small accident last year) and changed the oil. Used Mobil 1 5/30 and a Fram Oil Filter.
After about 125 miles of driving intermittent Red T.O.D. Always when ICE is running.
Oil level is OK - not loosing any oil. Filter and bolt on the pan are fine - no leaks.
View 9 Replies
PPH: (Possibly Pertinent History)
Original Hybrid battery failed April 2015.
1st rebuilt (Dorman) battery installed April 15 - Failed July 2015.
2nd rebuilt (Dorman) battery installed July 2015 - Failed October 2015.
3rd OEM (Toyota) battery installed October 2015.
Front end alignment (stay with me) May 2016.
Intermittent Red Triangle of Doom June 2016-present.
Installed Camber kit (yesterday...)
After I realized that I could duplicate the conditions for the triangle appearing/disappearing (brake/veer left to make it come on, accelerate/veer right to make it go away), I relaxed on the urgency of getting this addressed. After all - if the triangle goes away, there really isn't much of an enduring problem (I thought).
Brought the Prius to Legacy Toyota (Tallahassee, FL - BTW, I have only good things to say about this Toyota dealership) and the mechanic and I replicated the conditions while the Toyota diagnostic computer was attached.
View 14 Replies
Seems like issues with my 06 prius battery are back, however this time it is rather strange but very predictable. I cannot read any trouble code as the red triangle on the dash (and "problem" on the display) never stays on more than a few seconds (1-5 seconds at most).
At first it was doing this only after long downhill driving (like my 1.5 mile downhill street at 25 mph) - charging the battery and once getting to the last green bar I would get a Bip, red triangle and "problem" on the display. This has been going on for 4 weeks roughly.
But it's gradually getting worse, the same symptoms would appear after shorter downhill driving. And now it does almost every time I get the foot of the accelerator (assuming the car has decent momentum to regenerate).
I am guessing a module is starting to fail but last time I had a failed block, it didn't do that. One day I got the red triangle along with a bunch of other lights and that was it.
View 5 Replies
Strange thing on my 2006. Driving on curvy road, would occasionally get just the "Red Triangle" exclamation point (for a second or so) -- and also the word "Problem." would flash up on the display.
No permanent check engine light or other icons lighting up. Still getting 40MPH, everything seems to be driving right. Have 135K on the odometer.
Question - does that triangle thing store codes that can be read by an OBDII reader each time it flashes -- or does the check engine light need to be on?
Second Question - Any clue what the word "Problem." with no description could refer to? It goes away at the same time the red triangle goes away.
View 4 Replies
So let's start with this. A week ago my dad went to start his car after going to the store. I wasn't there so can't say exactly what happened but when I got there the car would basically go into accessory mode with check engine light VSC and triangle on. Also displayed problem on the screen. I checked 12v battery with just the radio on (one button press with foot off brake) and it only showed 12.0 volts. So I hooked our jump box directly to the battery and it still wouldn't start. I scanned it for error codes and it showed nothing but I could erase them and the lights went off so probably codes from one of the hybrid computers I can't read but the car still wouldn't ready. I unhooked the 12v for about 30 second seconds and the car started fine without the jump box hooked up.
At this point I don't have any codes and with nothing to go off of I'm at a loss. We drive it 8 miles back to our shop and it drove normally with no errors. Once it was back in the shop after turning the car on and off 10 times or so still no errors. On the last time it was in ready mode and the errors came back on, still with no codes I could read. His 12v optima was still under warranty so we got it exchanged for free even though I was reluctant that it would fix the issue. Well a week went by and all seemed to be fine until yesterday.
My dad had left the car in ready mode for probably 20 minutes and when he got back in it all the lights were on. I will also add that the battery fan was operating normally and not screaming like if there was a traction battery issue. I changed one of the modules in his traction battery about 6 months ago when one failed. Without any codes I don't know where to start with this problem. 2005 with 170k miles....
View 6 Replies
I've been having an on going issue where my Pirus will start beeping but there is no indicator light I can see showing any kind of issue. It will start beeping during startup and after driving for a while, no exact time something like after 25~30 mins. It sounds like the seatbelt beep but louder and both will beep when my wife does not have hers on.
I replaced the Aux battery(was old needed to anyway) with a yellow top but that didn't fix it. And again there is no indicator on the dash or display showing issues no red or orange triangles. Checked the prius's diagnostics but no codes appear under the diagnosis check I or II, sycheck mode or LAN monitor.
View 7 Replies
Have been driving my Prius with no issue all week. I leave the car home and take my wife's vehicle, while she drives it today without incident. I come home and hear the car making some strange beeping noise (NOT the anti-theft alarm, different). I hop into the car and try to start it, and the check engine and ABS lights come on for a second before other lights in the speedometer area kinda half come on. The gear indicator comes on and has boxes blinking on all of the letters.
The MFD never comes on.
It appears to be the 12V battery dying. The car has 150k miles and I have never replaced the battery, so it seems I was way overdue for this.
View 7 Replies
My 2010 Prius (130k miles) has recently started beeping on curves, turns and braking on occasion. The red triangle also comes on. There is no problem otherwise. It is a bit annoying. What is the cause of this? Could I have the beep turned off?
View 5 Replies
Recently while pulling into the gas station the brake, Triangle !, ABS and VSC lights came on. The dealer reset the error and said my ECU needs replacement at a cost of $1843. The Prius is a 2005 with 147000 miles. No problems since the reset so I am hopefull. I don't recall reading about a lot of others having to have expensive ECU replacements so I wonder how many have had similar problems and replaced their ECU.
View 2 Replies
The battery in the back looks like it got smashed a little. Do you think this is the cause of the lights? It was a small suv so it missed the bumper and went straight into the battery area. Trunk wont latch anymore the it got pushed in.
Is there an electronic box back there that could have caused the lights to come on?
View 5 Replies
Just bought 04 prius. Anyhow fast forward to yesterday and I am driving home and notice the Brake light, (!), ABS, VCS lights come on. I read a couple forums about bridging pins 4,13 to get codes and this is what I have. (!)69, 57 ABS 42, VSC 45
I tested the battery and it was 13.8 V on and around 12.3 or something off. I felt around where the inverter pump is and it feels like there something going on in the middle hose. I tried to look in the reservoir but honestly I couldn't get it pumping when I had the hood up so I couldn't confirm movement in the reservoir.
I reset the codes (stomping on brakes 8 times) and it went away until I started driving home again today and they;re back. I added a file the is the sounds I hear when pressing the brakes. Truthfully I hear this all the time when I turn off the prius. I just noticed though that when I hit the brakes I hear it now. In the sound file you hear a pause when I press and release the brake pedals and reapply.
View 16 Replies
I have had the Prius for a little over 2 years now. Bought used and currently close to 150K miles on it and have put on about 25K miles a year.
This evening on way back home, when I turned on the Prius, I got the Red Triangle along with a bunch of other lights ON the dashboard.
Pressing the power button and everything would take much longer than usual - the lights(on the clock) was dim, the windows moved up and down rather slowly.
Eventually, i had to jump start and carefully drive home. Afraid it would stop somewhere at stop signs or long red lights, i constantly kept pumping the accelerator(not sure if that was good). Seems like need to replace the 12V battery.
View 19 Replies
Bought my daughter a used 05 prius. So far had had to repair the MFD, ac blower, 12v battery.
The engine light, red car light, the triangle light turned on. We replaced the 12v battery since we didn't know if it had ever been replaced. Drive the car for about 5 minutes, then all the red lights reappeared followed by not being able to accelerate. Immediately drove back home. First looked up the acceleration problem and it says to check engine coolant levels.
Low and behold the reservoir was empty. Purchased some, added it and drove around the neighborhood. The acceleration problem gone! Engine lights gone! Just as I am getting home, the dash lights disappear and the engine light only is lit, and red car on MFD. I drove it to our mechanic for error codes. It drove perfectly. As i go to turn off car, it wont turn off. It took another 5 minutes of power button holding, brake release and parking holding. It finally turns off.
View 10 Replies
2007 Prius 215,000 miles. Car has been a champ for the almost 2 years I've owned it, buying it with 150K miles. No real troubles and I've been driving it constantly as you can tell. Had an extended warranty repair done back in the winter when dash lights went out completely yet car would still start & run. Replaced 12V battery back them trying to diagnose trouble and it was original battery anyway. Daughter was driving when almost all dash lights came on including the red triangle. She came back home, turned it off. Next start was just red triangle and check engine light with red car on center display. Now it's just the check engine light and red car after sitting for an hour. I plan to take it in to get check engine light checked out.
View 4 Replies
I replaced my rear brake shoes this past weekend. Immediately after I replaced them, the ABS, VSC, ((!)), and Parking Brake lights came on. I had not read that I should've disconnected the 12V battery before changing the shoes, so I wonder if that's related to the issue. I've read through as many threads here that I could dig up, but I still have questions. Here is what I know so far:
Car Info: 2004, 210k miles, Original 12V battery
Relevant Info: While replacing the shoes, one of the seals(?) (rubber part that slid over the piston(?)) slid off. I put it back on, and have checked for any fluids leaking, and have found none. I may pull the rotors off and check this again, though. There were no DTCs logged prior to the shoe replacement. Battery has shown no signs of dying, although I am going to check the voltage on it after I post this.
I tried jumping the pins, and I get the following flash codes (I tried resetting, but they came back immediately):
ABS: 4-2
VSC: 4-5
((!)): 6-5
I tried finding information on these flash codes, but have found nothing...
My CHS Tank was damaged in an accident a few years ago. I just replaced the CHS tank and the Inverter Coolant Pump within the last 12 months. It is still running when I power the car on and off as it should. I also jumped the fuse with a paperclip to double check that it runs.
My brake fluid levels are fine right now.
Possibly unrelated to the lights, but applying the parking brake is very easy. I don't think I adjusted the star adjuster enough. This is my first time messing with drum brakes, so it's possible I didn't adjust that correctly. Are these self-adjusting, or do I need to go back and adjust them by hand?
View 5 Replies
I have done some maintenance on a recently purchased 2004 Prius. Namely, replaced the inverter cooling pump, the right front wheel bearing and rear brake pads.
At a certain point, the brake, (!), VSC and ABS lights came on on the dashboard.
My wife is driving this car so I did not get the exact moment when the lights came on after my repair jobs.
I then replaced the 12V battery with a new one and reset the lights with the PIN 4-13 jumper on the OBDII connector. I did retrieved the error codes of each light and I googled them without any result and I now lost the paper where I had then written on
View 10 Replies
I have a 2008 Prius, with SKS and Nav, and 103,000 miles on the odometer. I bought it from the original owner in 2010. So far it has been trouble free, with just oil changes and scheduled maintenance.
When I turn power on, I get a red triangle with exclamation point. Also a row of yellow indicator lights. Also along the top of the LCD display there is a red car shape with an exclamation point on it.
I followed the procedure for checking the voltage of the 12v battery using the diagnostic screens, using the procedure at weird-stuff-happening-mpgs-dropping-test-the-battery.73400/and I got 11.8 volts.
Since it seemed likely that my problem is related to the (original OEM) 12v battery, which is now 6 years old, I took my handy jump-start battery thing (see photo below) and attached its red alligator clip to the positive post under the hood, and the black clip to the frame. I hoped that would allow me to start the car, but it did not start. The error lights on the dash were unchanged.
Question 1. Does the fact that the symptoms remain the same after I have connected my jump-start battery mean that the problem I'm having is NOT my 12v battery?
I then hooked up my cheap OBDII code scanner (see photo below) and checked for codes. It found none.
Question 2. Does the OBDII scanner not finding any codes have any importance? When people write about having their car towed to the dealer and having error codes read there, does that refer to OBDII codes, or are they referring to some other type of codes that can only be read by a dealer?
While I was in the diagnostic screens, I found three screens of error codes. The screens are called DSP-AMP, EMV, and NAVI. See 3 photos below.
Question 3. Do these error codes have significance?
View 19 Replies
