Prius (2004-09) :: Starts Fine But Idles A Little Rough
Feb 17, 2011
Just recently my Prius Taxi with 340,000+Km has developed a little problem,it starts fine but after 20-30 seconds it begins to feel like it's not running properly on all four cylinders,if i go to the exhaust pipe it seems like it's spluttering slightly.
Yesterday I changed the plugs,checked air filter and all connections,everything fine, when I accelerate it feels hesitant but after the car gets up to temp it seems to go away,it only happens when i start it first thing or if it's been left for a few hours, it's never had the throttle body cleaned and I'm wondering if what I'm describing is a symptom of this?
View 19 Replies
Advertisement
2007 5.4 . Starts good , idles all day. As soon as you try to rev it, it stumbles rattles etc. Shut it off, wait a second, restart then Idles fine. I watched live Data and it carries on when the VVT solenoids become active (above 800 rpm).There duty cycle goes to 60-70 percent while revving. I think it Is just one side of the engine. Could be VVT solenoids sticking on? yes ? No?
View 3 Replies
I have a 99 jimmy replaced rotary button, cap, plugs, wires. The truck doesn't seem to run right. It idles fine but when in load it starts to sputter a bit. Going down the road between 2000 and 2500 rpms the tach jumps a bit. Now if I put it to the floor the truck runs out fine.
View 3 Replies
Today I acquired a 1982 F150 with a 302 engine, 4 brl. Edelbrock carb. The truck starts and idles just fine, but when I come to a stop, try to give it gas to go it dies. It starts right back up, and I have to rev it high a couple of times then put it in gear and it will finally go. When I got it home I let it idle a few minutes and tried playing with the air and fuel mix but don't know what I'm doing, really. It seems I can hear a hiss, and when I was reaching for the air/fuel screws I got a little shock on the hand from the distributor. We want to use this truck as a farm truck, and plan to get a manual for it, but what might I might check for the cause of it stalling.
View 1 Replies
I have a 2002 Nissan Quest. It starts fine, idles great. But, when I try to accelerate, the car bogs, hesitates, misfires and I get p0300 random misfire, p0325 knock sensor. I get no dtc when it is just idling. The fuel pressure is fine, regulator works good, the cam sensor is clean, the coil tests good, the compression is good, as are the wires, cap and rotor.
View 2 Replies
The car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 Replies
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
View 11 Replies
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
View 13 Replies
So my "farm truck" is idling very rough, to the point that sometimes that it stalls out. At high idle it runs fine but when its at a idle its very rough. Its been running fine until probably a month ago or so and its just getting worse. What it could be? I am thinking it might be that something is dirty but i just dont know where to start with figuring out what the problem is.
View 9 Replies
The problem I have is when it is cold out under 40 degrees, my car starts rough and idles rough until it gets to temperature. My research has concluded it may be cold start. Does this sound right?
View 5 Replies
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.
View 14 Replies
I have a 2003 2.0 gas Jetta (181k miles, automatic.) that won't rev over 3k, starts rough, idles rough and wont stop setting a P0341 cam position sensor code.
The car was not running when i got it, i replaced the coil pack and it ran but not over 3k. Cleared codes, it sets the P0341 immediately.
Had timing belt, water pump, tensioner and cam pos sensor replaced. Still, sets p0341 code, starts rough, idles rough and wont rev over 3k.
The throttle servo makes a little noise when actuated, shop thinks this is my demon - suggests replace throttle body.
View 7 Replies
1991 Regal, 3800 v6.
So here's an interesting observation. When i turn the ignition to ON, I hear no sound nor feel any vibration from the fuel pump. Is there any scenario where a fuel pump fails to prime yet kicks into gear after a start? So, I've got rough idles and misfires on cold starts. Before I start replacing parts my diagnostic plans is as follows:
Remove and inspect spark plugs.
Inspect and test starter coil/distributor (still have to research how to do this)
Test resistance on fuel injectors.
Test pressure drop on fuel rails.
Test compression for possible small head leak.
I'm wondering, if I do have a tiny head leak that is letting in a drip or two of coolant after hours of the engine sitting, will I be able to see this on the gauge doing a compression test? I've never done one before and still need to buy a gauge, but maybe I'm better off just doing the other tests and if they all check out I can be certain it is a minor head leak.
My assumption is that I have a leaking injector; just trying to do things the proper way.
View 19 Replies
Just picked up my 2004 Prius from the Toyota dealer body shop. The driver's side was scraped by someone who wanted to be in my lane. Fortunately, we were only going 35 mph. The rear door skin had to be replaced, and most of the side had to be prepped and painted. There are a few silly mistakes: they forgot to replace the driver's door plug, forgot to replace a lower clip, and smudged a tiny area new paint on the bumper. I brought that to their attention and they are going to take care of it... they have to order the plug and clip.
However, as soon as that conversation was complete, it was time for them to close shop. I sat in my Prius, started it, and the check engine light was on. Wasn't on when I dropped it off for the repairs. Also, on the way home, I noticed the engine wasn't turning off when I came to a complete stop (even though the animation says it was off). At idle, the engine is also rough. Looked at the charge bars, and well, there were only two bars showing.
I thought perhaps, though it's not done this before without the animation screen showing it, the engine was on merely to recharge the traction battery. On the way home, the traction battery returned to full charge (green), but the engine still was not turning off when the vehicle was at a complete stop... not was it turning off when coasting... and when arriving home, even with the car in park... and still idling rough. All the while, the animation on the screen is indicating the engine should be off.
When I replaced the traction battery three years ago, I also replaced the 12v with an yellow top Optima. I wouldn't think the Optima is already going bad. I also do not believe in coincidence. I wonder if perhaps some bad fumes have tainted the MAF, or who knows.
View 9 Replies
My 94 850 turbo wagon starts rough and idles very high. the rpms dont come down. After turning car off, wont restart again unless I let in sit for a while.
View 11 Replies
We have a Ford Focus wagon that idles rough once the engine starts coming up to temperature. When you first start the car it's fine. For example, today I started the car, drove it up the road to the store and it was fine, but upon returning to my driveway just a few minutes later, as the engine temperature was just starting to come up, it started idling really rough. The idle is so rough it sounds like it's on the verge of stalling, but it never has actually stalled. An oxygen sensor has been replaced and it was good for a while, but now the problem is back. The check engine light is on as well.
View 2 Replies
I just got a 4.6 4WD Explorer in for rough running. It had timing chain noise and some odd codes for primary coil H codes along with cylinder 8 misfire.
I replaced the coil to get rid of the "H" code and it was fine. Still misfires on 8, and I really don't care because it's coincidence that the timing could be affecting it or perhaps.... bent valves!
The vehicle starts and idles a bit rough. Can't go very fast, and of course I know I should run it as little as possible!
Here is the deal, how should I present this to the customer? Should I let him know that some valves could be bent after replacing the chain (and all associated parts) and that it could still be effed? Or will I be fine after replacing? Pretty much, where they had a tensioner failure/guide breakage and valves bent too?
View 14 Replies
I have a 04 ls that has been with a mechanic who gives up. The car idles fine but has no power or acceleration all COP's have been changed. Also the computer is not throwing any codes. Mechanic says that cylinder 3,2,1 have sever mis fire and are pretty much dead but dose not know why.
View 3 Replies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
View 5 Replies
I Have a 93 bronco with a5.8 the truck will start up and run fine for a while and then the engine gets really ruff starts back firing and shuts off it only starts with starting fluid or after it sits for about 30 mins.
View 7 Replies
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....
View 2 Replies
