I drive an 06 Prius and it just started making this squeaking sound from the wheels when I steer. When I make turns you can hear the sound both ways when turning the wheel.
I took it to the dealership for the steering recall but they didn't seem to find anything. Is it just something I can lube up to make it go away or is it something more serious?
I have been hearing a loud squeek coming from the wheels in the front. It sounds like a brake wear bar but isn't it a little early to replace the pads already? I searched the forum last night briefly and found some threads where people commented the brakes should last much much longer than 50000.
I do not ride my brakes and I don't think I am hard on them. They still work great and do not feel worn. The noise is constant (not only when i turn the wheel) and it goes away after a certain speed.
I had the front struts replaced. I looked at the strut diagram and replaced most of the parts associated with the front struts. The rear shocks were also replaced. New brakes were installed on the front and rear. The front rotors were replaced. Mileage 124000 miles.
I thought this would might solve the squeaking when I went over a speed bump in the parking lot. It did not. How to fix the squeaking.
We had a terrible grinding/juddering on front wheels when turning which did disappear after driving for a few minutes most times, what the problem might be?
View 1 RepliesWhen turning left , I felt that there was a shock from front wheels. The service person told me that it was a differential problem and the controller unit is needed to reprogrmmed. Is it true? When my Touareg ran over the bump, I felt that the front suspensions were not adjusted well. Is it normal?
View 2 RepliesHave my truck in signature making a very high pitched, annoying squeak from the front end. I believe it is coming from the right side because i just took the wheel off and it has a coating of brake dust on it (the 3 other wheels are clean). Only makes the noise when turning right at speed, and goes away when i straight it out or hit the brakes. I am not very good with brakes or the front end parts.. what could be causing this noise? Could the slide pins be frozen? i know that is a problem with these trucks... but not sure if these are the symptoms.
View 14 Repliesi have a Subaru legacy rs 1996 twin turbo, about 6 months ago now i replaced both front outer CV joints and boots due to a grinding when turning at slow speed e.g a car park. the grinding had gone and its was all fine until now the same grinding as come back. its it normal for the CV joint to wear out that fast or could there be a different problem?
View 5 RepliesStarted hearing a squeak from drivers front wheel area when turning right, thought maybe pads might need replacing but they were fine as were the pins. So I checked for play with tire off ground and there was def some play pulling from top to bottom, so that lead me to the front hub, I read some posts about pulling the abs sensor and getting some grease in the the hub bearing so I did that but when I replaced the sensor and spun the hub it was scrubbing on the bearing.?
So I shimmed the sensor with a washer but now the abs light comes on but there doesn't seem to be a squeak when turning right anymore. Any example of doing this and had the sensor scrub? And with the play I would assume I need to plan to replace the hub assembly fairly soon...
2000 X 4x4 V10 with 147k
2005 2.3Liter 4wd Mariner, 225k miles
I have been experiencing clunk noise on the front end when braking or accelerating and turning wheels.
I have replaced: front control arms, ball joints, tie rod ends, sway bar bushings and stabilizer links and 2 days ago I replaced strut mounts and bearings.
The steering is smooth after the strut mounts replaced but I can still hear cluck noise mostly on left now when going over bumps, braking and accelerating.
Car also has new engine/trans mounts.
I am so lost right now because I cannot figure out what is it. The only thing I didn't replace are the struts but the I test them and they seem to function fine.
I have an 04 GLI with around 130,000 miles. I have developed a squeaking noise coming from the front end of the car. I cant really tell if its the right or left side. I can tell you i only hear it when driving under 30 mph and it seems to happen more often when i slightly turn the wheel to the right. Also when i accelerate from a stop or let off the clutch pedal into 2nd or 3rd. I wonder if it could be the wheel bearings going bad? I replaced both front and rear control arm bushings back in December just for some background. FYI, by squeaking i mean the sound of metal to metal. Its not a squeal or hiss, or anything to do with a boost leak. When you hear it, it sounds like a squeak, squeak, squeak kinda pattern but comes and goes depending on speed and the turning of the steering wheel.
View 2 Repliesso I was heading off the freeway to take my exit at night. Didn't see there was a little curb island between the main freeway and exit. Went with the car over the curb and my right passenger tire went out.
I changed the tire and driven off, then noticed the car sound got much louder all of a sudden and when I turn the steering wheel right or left, I hear or feel a heavy sharp sensation- yet the car turns fine, it just sounds louder when I press the gas and when I turn the steering wheel I can feel my feet vibrating a bit and a soft/sharp squeak sound comes out.
What could this be?
Have a moderate pitch whine in front end only when steering or turning to right. Gets louder w higher speeds but pitch is about the same. Thought it was a left front wheeling bearing. Also needed new pads and rotor. While doing the job noticed grease all over the lower ball jt. Discovered a tear in the outer axle boot. Net net replaced pads, rotor, axle hub assembly and axle complete. To my chagrin the noise has changed one bit. The noise also doesn't change when I put the car in neutral while traveling downhill. With the hope that I replaced the wrong bearing I have ordered a new one for the right passenger side. When I tried the 6-12 wheel rocking test on the right there did not appear to be any looseness.
View 5 RepliesI have a 2000 Mercury Mountaineer 5.0L V8. Recently it has developed a squeak in one of the pulley wheels. I think it is the middle one but it may be the alternator. My question is can I change these pulleys or do I even need to? My mechanic said its nothing to worry about but I am of the opinion that bad news does not get better with age. A squeak indicates that something is not right.
View 3 RepliesI have a 2005 KR that the 4wd doesn't lock in the front wheels. I haven't seen my exact problem as I have been searching it. When I turn the switch. The dash lights both in high and low 4wd. I hear the transfer motor engage in both hi and low. No ratcheting noises from the wheels. I have replaced the solenoid. And still nothing. Checked fuses And they are OK.
View 3 RepliesI just recently bought a used 2004 fx4 with 148k and everything appears to be engaging but front wheels not pulling. I've already replaced the IWE solenoid behind the battery to avail, my question is, when I put it in 4H, light comes comes on, but I don't "feel" the transfer case engage, when I put it in 4L, light on I feel it shift. So could the shift motor not be engaging the front driveshaft even though the lights come on?
View 10 RepliesMy 96 xj started to get this annoying squeak on the passenger side. It does it when you turn the wheel in any direction, I traced it to the wheel hub area but not sure what is causing the squeak, i just replaced the tie rod and I went and greased all the fittings on that side side but it still does it The ball joints were replaced just over a year ago.
View 9 RepliesI jacked up both front wheels and I can't move them at all. I was able to get the car into neutral and still they won't move. emergency brake off as well (even though that only stops the rear wheel) Could the disc brakes be too tight or could they just be on all the time somehow? I had noticed that when driving, it felt like the brakes were on. This feeling was especially evident when taking my foot off the gas pedal to glide on flat ground, and the car would slow down faster than I thought it should. Also notice a huge drop in MPGs. I know the car is FWD, so maybe there is supposed to be resistance but I can barely get either wheel to turn more than an inch or two.
View 12 RepliesJust wondering... should there be any plastic pieces inside the wheel wells directly in front of the rear wheels? There is empty space on mine where it looks like leaves and whatnot could collect. I can get a picture if needed. I expected there to be a plastic cover of some sort. Then again, maybe it is on purpose so if stuff collects in there you will see it and clean it out.
View 8 Replies109K and runs great except for when accelerating from start to any speed. The front end acts likes the front wheels are slightly out of balance. Once you stop accelerating all is fine. Tires have plenty of tread and no I haven't rotated them to the rear which I might do?
View 1 RepliesI have a 2006 XLT w/ the 5.4L engine. Manual transfer case, I'm wondering where to start looking for problems w/ the 4x4...the front wheels don't engage.
View 3 Replies2006 Lariat 4x4 Troubleshooting. My front wheels wont engage when I select 4H or 4L. No dash lights are ever lit.
I read up and understand how the system works and plan to replace the solenoid, transfer case motor and both hub actuators. I swapped out the solenoid and wanted to test that it was functioning properly so I followed the video below:
YouTube........
With the engine running and selector switch at 2WD, I pull the vacuum lines off and can feel vacuum at the supply. I then hook up just the supply line up (to the bottom port) and expect to feel vacuum at the other solenoid port (top port - what I would call the outlet) and cannot feel any vacuum.
This has halted my repair attempts as I am not convinced this is functioning and would pull in the actuators if they were functional. I know it's a small vacuum from a small orifice but I would think I should feel it by hand, no?
The solenoid's electrical connector is plugged in during this as well. I get the same performance with the old solenoid and the new. If I bypass the solenoid I can feel vacuum at the front wheel hubs.
Should I try a third solenoid? Seems unlikely I would have 2 bad ones...No OBDII codes at all. What to try next?