Cleaned the engine and determined the location of this oil leak. I am posting two pics. The far away shot shows the leak in the center of the picture...near the motor mount. The close up pic u can see the leak coming from a vertical seam just Below where the half shaft enters the transaxle. It is definitely motor oil, not transmission oil.
View 5 RepliesI have noticed oil spots under my 06 lately and finally got under it to see where it's coming from. It's collecting and dripping from the bottom motor mount but it's hard to determine exactly where it's coming from. I can't tell if it's coming from higher up or down low and running back and up from the wind. I just cleaned it with degreaser and have it running to hopefully dry it and be able to see where it's coming from.
View 11 RepliesI have a 2009 toyota camry le 4 cyl with 170000 miles. I had my rear main seal replaced because there was an oil leak. Now after I got it back from the shop, there is a oil leak near the front motor mount and my engine had gotten louder when i accelerate. also it smells like paint or something inside my car. what did the shop do?
View 3 RepliesI need to replace the motor mounts on my truck. Is there any special tools or tricks I will need before I get half way into it and find myself in a bind? Oh yeah it's a 5.4L
View 1 RepliesThe vehicle in question is a 96 Buick Century. I don't use it a whole lot, but occasionally lend it out or use for some undesirable task. Anyway, I have to get it to pass inspection.
View 4 RepliesI need to change the all support mount motor of my Camry 2003 v2.4l. but I don't know where find the best model or manufacturer.
View 2 RepliesMy passenger-side motor mount is cracked out. Is this a common failure? The aluminum part that connects the "frame" to the engine mount is cracked, the hydraulic rubber mount looks almost new, not sure how the previous owner missed the crack in the aluminum. Car has 140K miles on it. I'm thinking about just having it welded up.
View 8 RepliesWhat hardware I need to install the passenger side motor mount spacer from Euro Image Tuning. Been sitting on it for a while and cant find the hardware that it came with. Would like to install it, but dont remember what it came with..
View 2 RepliesThe passenger-side motor mount on my '99 1.8t has blown (again). I'm on my second mount already and want to make sure I address all other possible causes before I go through another one. Looking for keeping this new mount intact a bit longer? (BTW the original mount lasted approx. 120k miles and the replacement has "only" lasted 85k miles)...
View 4 RepliesThe other day when i wanted to start the car, I found out my battery was death so i decided to ask my buddy to push me and crank it on gear. Car shakes as normal and engine started, but then i heard a weird noise like if something was rubbing. I turned it off and popped the hood. I found my engine leaning forward and toward the passenger side.
So the next morning, I checked the bay again and i found out that it wasn't the motor mount. Motor mount is ok, but then i found a broken bolt that holds the bracket to the block; the one that goes right next to the water pump to be more specific. Also in the back of the block there is a bolt that hold bracket to the block again and the thread whole was enough weak to break when the other bolt failed. So I did some research and i found that there is a solution for the bolt in back of the block.
What I am concerned is for the on the goes right next to the water pump. It seems that it broke the whole thing including the part where the bolt threads go. I just had a shop install I.E connecting rods, new piston rings, and rebuilt the heads. They put a new timing belt kit and all its job required. I think they might have a bit of fault on this since it had to be removed when they did the timing belt kit. Anyways I don't want to think my block will be a junk now because engine is running like a champ, and that would be a bummer.
-Bolt that is broken in two pieces.-
-And where it is attached to the block-
-Part of the engine where this all goes.-
I can't get my front (passenger side) motor mount out because it's under the refrigerant line. How would I do that? There is a black, coiled "jacket" that goes around the line right before it enters the back of the radiator, can I detach it there? The line snakes all over the engine compartment and appears to be bolted onto the radiator on one end and the other end goes through a clamp and into the dash area. [URL]....................
View 5 RepliesThe front motor mounts are bad. This has been confirmed. When I am cruising at a constant 45 or 55 mph and choose to accelerate because traffic is clearing, etc. the car will thump a bit and only slowly creep faster. It feels as if there is very little response other than the mild thumping. Getting to 65 mph takes time. The car has 70k miles and performs almost flawlessly at slower speeds. Is the thumping/lack of acceleration a symptom of the bad front motor mounts?
View 12 RepliesMy 99 Passat 1.8t broke down on me last night... my front motor mount is missing and my motor snaps back from time to time but last night i think it went back all more than normal and as soon as it snapped back the motor cut off and won't turn over... it will crank and crank but not turn over. i looked for any loose wires or anything possible that could be out of place and couldn't really see anything out of the ordinary... There are 3 sensors right next to the power steering reservoir that aren't connected but don't look like they were connected, need to identify those sensors.
View 2 RepliesI have a 97 f150 4.6 4x4 i cant get my engine to line back up with the motor mounts. Is there a trick to doing this? I've tried to lift the motor several different ways, but still nothing. Its like the motor isn't going back far enough. But it cannot go back any more without hitting the trans?
View 8 RepliesI was sitting at the stoplight in neutral when the light turned green. I pushed in the clutch and put the car in first then all of a sudden a huge CLUNK like when you take out the starter bolt without supporting the trans or motor. Then while letting out the clutch about halfway all hell broke loose. It sounded like a bunch of marbles rattling like crazy in the trans. I pushed the clutch back in then it stops until you let it back out again. The car still moves forward and reverse but with all that noise. The sound seems like it's coming from under the driver side motor mount. When I put my hand on the tranny I can feel the vibrations very well. Does this sound like the throw out bearing?
View 3 RepliesMy 2006 AWD LTD 500 has about 52000 miles on it; a slight rattle/clunking noise is intermittently heard on driver's side in engine compartment. Took it in to dealer who says motor mount is cracked and front stabilizer bar joints are worn and both need replacing. Car has only been driven on highways or for short trips (3-4 miles) and has had no impacts nor been driven over rough roads or run over any potholes or such. Should the motor mount be damaged? At 52K miles?? Never heard of such a thing. Ditto, the stabilizer bar joints: worn out in under 60K miles? What can I do about this? Who seek relief from? Ford warranty is, of course, over, and supplemental warrenty will only cover motor mount replacement but not stab bar. Are these parts routinely wearing out at such an early date that repair shops can reap the rewards???
View 4 RepliesNoticed an ATF leak on my van on crossmember/tailpiece mount awhile ago. Not the driveshaft seal but near mount. Checked tightness of bolts on case and mount and found the one mount bolt that goes into transmission case loose- about one whole turn.
(other bolt is on an "ear" of tranny case) Checked again after a couple of weeks and leak is worse, same bolt is loose again.
Is there a gasket or O-ring on this particular bolt? 1998 Ford E-350 with 6.8L - trans code E on door sticker. I believe it is an E4OD as the tranny pan says "Metric" (?) 324,000 miles on this and runs/shifts fine. Occasional vibe issue at highway speeds... I've added 1 quart of ATF over this time period.
Just picked up a 05 with 99500 on it. Drives fantastic and previous to this I used to have an 05 way back that I drove new to 64k. Anyway I test drove it in the rain and with chatter between my wife and I with the sales rep I didn't notice it but now I found that there is a whining noise coming from the timing chain area of the motor. Its only when the car is on and it gets louder as you go towards the passenger side and away from the hybrid components. Here is the sound from my iphone near the motor.
View 3 RepliesRecently my a/c in my 2007 prius has been on the fritz. Some days it chooses not to blow any air at all. Others it will blow upon start up with cool air. I just took a road trip and it didn't work for 2 hours then magically came on blowing cold air. I took it in to the local shop to see if they could figure out the issue. To my disappointment, all the "parts" appear to be in good working order. The technician said that the electrical system just wasn't getting to the blower motor and that I should take it in to Toyota.
View 4 RepliesI have about 05 with 110000 miles on car and have started to notice that the motor sounds like it is revving up when I come to a complete stop or even hyper miling. I have plenty of juice in battery Not Green and Not Orange. While at a complete stop if I switch from Park/drive/Neutral some times it will then shut off.
View 6 RepliesI have 160k on my 2005 prius. When letting off the gas peddle in DRIVE the motor is reving up to 4k with out the trans kicking in and moving the car. I have replaced the 12v bat, cleaned the t-body and mass air sensor.
I took it to the local toyota dealer for a recal and now they have had the car for over a week. I am being told it is the floor peddle sending a false voltage to throttle body. I highly doubt that this would not make the care go and not just idle up to 4k.