Prius (2004-09) :: Noise In The Right Front Wheel - Bearing Failed
Dec 17, 2010
I devloped a noise in the right front wheel. I thought it was a tire going bad so I rotated the tires & still had the noise. I was told by shop it is a wheel bearing. If that is the problem is that a DIY repair ?
View 5 Replies
Advertisement
I have the dreaded front wheel bearing noise front left had a monsoon last month in orlando. Went through a puddle. Did the front right 8 months ago,everythings fine I am doing uber. Can I spray some deep creep or oil in there to tempt calm the noise?
View 1 Replies
For several days I could hear a scraping sound from the right front side. I thought it was snow packed in the wheel well at first, until there wasn't any snow there. Today I was driving on the Xway and the scraping became a buzz like a Cessna airplane. On the way back home I turned the steering wheel back and forth and sure enough the buzz came and went. That made it sure to me the wheel bearing was bad.
View 19 Replies
At about 20k on my 07 I started hearing a faint whup whup whup between 35 and 50 mph's on the front driver's side area. At 60+ pretty quiet. It has gotten real loud at the present 30K. I suspected the tirers as I know the Integrities are complete junk but as a test I did a rotation and exact same noise.
I thought thats not good but found it hard to believe something else was bad as I had no vibration and no pull whatsoever in steering. Long story short I bought a new set of tires Kumho KR21's at stock size and oh crap exact same noise.
View 10 Replies
noise in my front end. I know there is a lot of stuff going on there so let me try. Noise is more like a groan not a squeak, tick, not an engine noise or a brake noise. Applying the brakes or turning the wheels does not make a noise. Best way to describe it to me it is like a bad bearing type of noise. The noise is starting to get louder.
View 19 Replies
So on my girlfriends 2000 echo I get the classic bad wheel bearing noise/vibration on the front left (driver side) wheel. Worsens under load (right turn) and goes away when unloaded (left turn). I've replaced left side bearing, CV axle, brake rotors/pads and the noise still persists. My next thought is maybe the ball joint but humming/vibration tells me something out of rotational balance. Bearing in the transmission? I don't know. I'm stuck.
View 5 Replies
My question is what could cause a wheel bearing and CV joint to fail immediately after a clutch replacement and a general inspection?So I brought my 2014 focus with under 50000 miles in due to the normal transmission issues with clutch chatter and hesitation. Also asked them to do a general inspection to come current on my warranty requirements and address a feeling of the car feeling lose into turns sometimes (I thought maybe it is just me getting used to going to summer tires from winter). So they rebuild the clutch and i finally get my car back four days later with a clean bill of health and them unable to recreate the lose sensation in the steering during a test drive.
So fast forward four five days and under 200 miles driven and I had a rapid failure of my front driver side wheel bearing and cv joint. It was fine the day before then after 20 miles of driving it felt like it was about to go. So this is everything I noticed about my car after I got it back:Transmission felt great. No chatter and fast to respond. When I would turn into a parking spot or pull out of one I would sometimes here a clunk (that had never happened before) Drove fine. It rained the day before the failure (not sure if that could contribute) but when I got on the road the next day the wheel went bad very very fast and the rubbing became so severe I limped to the nearest cellphone reception. A 79mile tow later I am back at the dealership who replaced that the wheel bearing and CV. (my car is actually back there right now because they left a bungee cord attached to the coil and it started to make the clicking rubbing noise so I called them to tow it).
View 12 Replies
So my front right Wheel bearing is making noise and its a used Knuckle so its w/e. Guess ill use tonight to do all my bushings and fluids n stuff.
View 6 Replies
Having issues with noise from either LT or RT front wheel bearings? My 2011 Elantra has some sort of noise coming from the LT frt wheel
View 10 Replies
I have a 03 explorer with approx 160k, I am experiencing a thumping noise while driving. It gets worse on right turns and gets better on left turns. initially i thought LF wheel bearing so i ordered a hub assy and replaced LF. noise is still there. I guess, thumping noise caused by wheel bearings, i know its usually a grinding kind of whirring noise.
The noise doesn't seem to change with accel/decel so I don't think it is driveline related (diff, drive shaft etc.) should i bite the bullet and replace the rf as well??? I should also mention that there is also a shake in the steering wheel that seems to coincide with the thumping (i.e., my hand shakes along with the thumping, and the shake gets worse when the noise does)...
View 8 Replies
What is causing the right front wheel bearing to keep going bad on my 06 f-150 2 wheel drive....
View 1 Replies
I just had front and back brakes replaced and there is noise coming from front (I think it's the front)? Any way my brother says its the wheel bearings and that my mechanic should have "caught" that they were bad. I've gone to mechanic for almost 10 years and trust him. Never had wheel bearing problems before so not sure what to think. And if it is wheel bearing can u ballpark cost to fix in Illinois ?
View 10 Replies
I have a 2013 Elantra, new in January, 6600 miles on it, and I took it in to the dealership today because it was making funny noises this week from the left front wheel; the noise gets faster as I drive faster. The left front tire has a bubble in it, and they're telling me the wheel is bent and the bearing is cracked, so they'll need to replace the tire, wheel, hub, bearing and do something with the alignment AND it's not covered under warranty because it is "impact damage." Is this even possible on a new car like this? For the bearing to be cracked without a big accident? I don't remember hitting a pot hole or running over a curb. Shouldn't this be covered under normal use? I'm concerned that I'm being ripped off
View 16 Replies
I'm working on a 02 explorer. The front end is howling so I replaced the left side and no change. The howl goes away when braking. Is it the right side then or something else? I replaced both front brakes pads so it's not that.
View 2 Replies
I have a 2007 the front wheel bearing started humming real bad, changed it out. Can't seem to get the right front brake bled good. Did it three times. No air. Today locked up the left wheel upon putting on the brake, the right one ain't working. Is there any thing I can do other than bleed the left front again, check fluid?
View 2 Replies
I have a 94 Explorer. I recently swapped over from auto to manual hubs. I followed a detailed write-up that I found online. During the process I repacked my outer wheel bearings. Ever since then I hear a grinding noise coming from the front wheels. Sounds like the bearings aren't seated properly. The guide that I followed instructed to torque the spindle nut that sits next the the outer wheel bearing really tight in order to seat the bearing, then loosen it back up and hand tighten it. But when I loosened the spindle nut the wheel bearing would pop back out. What is the best way to get a wheel bearing to stay seated properly?
View 2 Replies
My 2005 Prius has 95k miles on it. I've been hearing a cluck-cluck-cluck noise from near the front driver side wheel. I had an independent mechanic test drive it, who said the wheel bearing needs replacement. Should I have it checked out by a Toyota dealer? They're so much more expensive, but are is it worth taking it to them?
View 15 Replies
Repeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!
View 7 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
My girlfriend and I just bought a 2011 a few weeks ago. We test drove it a couple times ourselves, and had our mechanic take a look at it and drive it also. Everything looked and sounded good. Not sure how much it matters, but it's a Certified Used as well.
A couple days ago, returning from a 45-minute drive which included some short stretches of gravel road, I noticed an oscillating sound. It's definitely not a noise that was there when we bought the car. Unfortunately, my cell is apparently bad at capturing audio, so hopefully my description will be enough.
The noise is very faint, almost inaudible, at low speeds. Between 30 and 35 mph it gets much louder, peaking at about 33. There's some vibration through the accelerator pedal also. Above 35, it fades pretty quickly and I can't really hear it at 50. The sound itself is 3 beats on, 1 beat off, about every second. There's a slight difference in pitch between each beat.
If that isn't enough to go on, let me know and I'll give the recording another shot and upload it if the noise is audible.
View 6 Replies
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies