My cars been stalling , won't drive up hills can't really get over 25 - 30 mph and I'm getting a sound from the fan in the back. These 3 error codes could mean for my 2007 Toyota prius
View 19 RepliesThe Prius has 115ooo miles. It is a 2005. Just recently it started showing the red triangle of death, check engine light, and the brake light. When I check for codes using a scanner it comes with the following:
P0A80
C1310
C1259
P3015
I have a 2004 Prius with 80k miles. Always has been a workhorse. Recently had a bad cell in the HV battery. Battery rebuilt with new cell and now works great.
Now it runs about 20 miles and then displays dash lights of red triangle and small exclamation (brake?) and VSC.
I took it to Advance Auto and their scanner reads C1310 'Malfunction in HV system'.
I actually replaced the entire HV battery again with the battery from my friend's car, and the 12V battery too, but no luck. Same error.
If i disconnect the 12v battery for a while, it will clear the code and the car runs fine for about 20 miles and then dash lights come on again.
Car runs perfectly, over 50mpg even with the dash lit up. What that code is?
Here is my situation- back in 2014 I had a local mechanic replace my HV battery and 12V battery after the Red Triangle of Death. Well yesterday that triangle reared its ugly head again! (and cruise control stopped working) Since this mechanic has 3 year, 36,000 mile warranty on all parts and labor, I figured this should be covered. I drove my wife's car to work today, then after work drove the Prius over there to find them closed until Friday!
So I had the guys at Advanced Auto read the codes for me and got P3006, C1213, and C1259. I have done extensive reading and researching, much of it on this site on these codes, but my main question is this:
I commute about 20 miles one way, and on certain days my wife commutes 10 to 22 miles the opposite direction. There are 3 days we go opposite ways this week, and at least one that is completely unmanageable without 2 cars.
The red triangle light and the car with the ! Light went off and these are the codes the local shop has found:
- P0121
- P3190
- P3191
- C1259
- C1213
- P3101
The shop I went to in Little Rock would not touch it. Need to put these together and diagnose where to start?
I have a 2006 Prius, It has 165k miles. Recently it gave me a code to replace hybrid battery pack, I read this code with my scanner from HF. I have changed out a battery pack with replacing the bad modules before so I am not a bigger with the system. I took out the pack and checked and it seemed like all the modules are in the 7.8 range. This was confusing since the code reader was saying to replace the battery pack. I put it all back in the car and tested it again and got the same results. It seems like the HV system is not being recharged any longer. It seemed odd, normally when I remove my foot from the gas the system shows the car regenerating power.. Now when I step on the brakes I only see that. The system does charge but randomly it will drop down where there are 1 to 2 bars left and then charge back up again.
P0a80
C1310 malfunction in HV system (when i read about this people say this is a ghost code that comes up from the battery pack.. but maybe not in my case.
OK, I finally resolved the bad skid control ECU, so I have no more codes relating to ABS sensors or pump actuator. Still get a C1310 when travelling at speeds over 60 for 10 minutes or so. After the car sits for a while, the idiot lights, triangle, ABS and brake lights disappear and the car runs fine. Except it has been whining at acceleration and deceleration a bit more than I remember. When I hooked up Tech stream, I got a P0A2B which is - Drive motor "A" temperature sensor circuit range/performance. Please tell me it isn't transaxle. Why does it only happen at high speeds? I can drive for 20-30 minutes around town without it triggering the dreaded red triangle.
View 4 Replies01-d5 190-45-c
01-dc 190-75-5
01-dc 1c6-0f-f
01-de 1c6-2b-1
The aux battery was changed about 9 months ago and the only problem I currently have is the tag lights are not working.
I have a 2005 Toyota Prius with about 150K miles on it. After work one night i hit a pothole and my ABS and BRAKE lights came on. I took it to a garage and they could t find anything wrong with it so they reset the light. It came back on about a week later (no potholdes this time) and i took it back. They hooked it up again this time it said there was an issue with the computer coding. So i took it to a Toyota dealership. They hooked it up to all their scanners and could find nothing wrong with my vehicle. They recalibrated the sensor and the light went off. Now a week later it is back on again. Brakes work fine and we get no error codes.
View 10 RepliesThe red triangle warning on my dash recently came on so I am taking it to the nearest dealer on Monday. I think all of this is covered under recalls/warranty. Am I right?
View 4 RepliesI just bought my 2006 Toyota Prius about a year ago in 2009. About a month or two ago, the check engine light came on and stayed on along with a big red triangular warning light.
I brought the vehicle into my local Toyota dealership so they can diagnose it.They told me that they had 3 or 4 different "codes" coming from the machine when getting the signals from the check engine light. All the codes were related to the cooling system. They said that they felt that there was "debris" clogging the pathway for the coolant flow throughout the engine. They had recommended a "coolant flush" for the hybrid side as well as the mechanical side.
So I had them perform the coolant flushes. After leaving the dealership that 1st time, the check engine light came back on the next day. I called the same dealership and explained it to them. They asked me to bring it in again.
SO I brought it to them a 2nd time. They diagnosed it again. They told me they came up with 2 of the SAME "codes" and 1 that was different, but ALL the codes were STILL related to the cooling system. They explained to me that something was preventing the clear flow of coolant throughout the engine. And since the thermostat was the only major obstacle, they recommended that I replace it. Well, I did. And after I left the dealership that 2nd time, I was praying that this was the last of my Prius issues !
The check engine light came back on the next day. The service person invited me back and did not charge me this time because it was the same issue. I told them that I am not in the business of randomly changing parts on my car unless I am absolutely sure I know exactly what the problem is. HOWEVER, this time they kept my vehicle for a good week or two. Running it through various diagnostics tests overnight here and there.
They finally came out and said that they feel that I have a coolant system leak coming from my engine and that I need to replace my head gasket which is responsible for sealing the engine.
During my 1st visit, the codes were P0117 and P1150
During the 2nd and 3rd visits , in addition to those, there was one additional one that came up that I will post as soon as I find it !
So I received the P1121 and took it to the dealer. They told me I also had a P3000. I called another dealer and they said the P3000 could be caused by the P1121 not giving it enough coolant. So I brought it back to the house, bought the valve listed in the forums, and I spent all day changing that + the coolant. I drained the coolant and between the reservoir and the radiator cap itself I refilled about 4 QT, and I saw that my inverter coolant was just below the low line, so I filled it up to the full line. Afterwards, I tried to get the coolant to flow, and it seems like I won't flow. The check engine light immediately came back on and the car said, "Problem." So I immediately shut it off and let it set for a few days. How do I get it so that the coolant starts flowing again. I haven't seen any of the levels move whatsoever on the radiator.
View 8 RepliesI recently replaced my engine water pump at 164,000 miles on my 2007 Prius, the car sat for 3 weeks while waiting to gather needed parts, i.e., water pump, coolant and Airlift system for adding coolant fluid. After installing the new water pump the car ran rough for 5-10 minutes upon initial crank (parked for 3-weeks). I took a 20 minute test drive around the neighborhood that evening, outside temperature around 65 degrees F, and car ran fine. SOC looked ok, bars moving between Blue and Green, everything appeared normal.
The next morning, I backed out of my driveway and the Red Triangle of Death appeared on the dash so I parked the car.
That evening I hooked up OBDII ELM327 scanner using Engine Link and picked up 2 separate P0A80 error codes, 1 of them was pending. I disconnected the Aux battery for 3-5 mins to clear the error's, Red Triangle of Death was cleared, then drove the Prius for 20 minutes with no errors or alarms. SOC seemed to be normal. OBDII ELM327 scanner showed the HV batteries were charging at same level, 16.8V and Aux battery was registering at 14.0 Volts.
The next morning, after 20 minutes of driving the Red Triangle of Death appeared, and shortly after I experienced loss of power, with sporadic engine idle and interior traction battery fan was on. Luckily I had made it to work and was able to pull into a vacant parking lot.
I did notice that around the time the Red Triangle of death came on this morning the SOC dropped quickly to 1 Purple bar and was slow to charge then shortly after came the loss of power and sporadic engine idle followed by interior battery fan.
Had a shutdown with error codes P0078 and P0092 on the scan gauge. Reset the codes with a scangauge and the car goes drives fine. This has not repeated for a couple of days but I was wondering where to see a list of Gen2 codes so that I can better understand what happened.
View 5 RepliesMy son drives our old 2005 Prius with over 300000 miles on it. He had a front end accident a few years ago, and, after body repair and a straightened frame, the car has been running pretty well, although the mpgs have been in the low 30s. This may be the result of his "lead foot." He recently saw the check engine light and the car shows the codes P2601 and P1116.
View 7 RepliesIssues:
1. Getting beeping noise like the keys left in the ignition when the doors open although they are not- battery is good.
2. Red triangle on start up with warning about Transmission- Parking brake does not sensor as being on, when on - in the diagnostic screen.
3. Fog lights are no longer operating when just the parking lights are on, but are when the headlights come on.
These issues may be separate but they all kind of happened in the same time span.
Background - 2009 Prius, Optium Battery initially installed Spring of 2012, over 66,000 miles. Battery is good, all fuses are good.
Since installing the Optium Battery I have had to change the battery about four times - as I am not always driving so I keep a 12v battery on the ready on a battery maintainer just incase I need to change batteries - not optimal, but it works for now. For this reason I turn the SKS off.
Last week my FOB started working erratically for about a week. I would have to press the button several times to get my door to open. Then it started working again like a champ. The battery in the FOB was changed by the dealer in September.
I regularly use the fog lights without the headlights. At the start of the week the fog lights no longer worked with the parking lights and only with the headlights.
Later in the week the car started beeping whenever I exited the vehicle from the driver's side. The beep was the constant short beep like when you leave your key in the ignition. I had not and nothing else was on (I read the post about the guy who moved his car for a family function.) This is an issue I associate with me having to change the battery, however it would have to wait to the weekend and an onboard diagnotic indicated that my battery with load was running at 13.9volts. Every other time I would start the engine I would get the red triangle and retry and the car would start up fine.
I was not able to make it to the weekend to change the battery and had to get a jump to get home on Friday. Upon initial start up after the jump and changing the battery the car indicated that there was a problem with the transmission ... park on flat surface... (Message goes to quicky for me to write it all down and I could not repeat the situation to get the message again).
I got the transmission p lock mechanism error. following the advice of the multiple threads, I removed and replaced the old battery after testing it. I drove about 40 miles and the triangle came back with the vsc and yellow exclamation highlighted too. The cruise control quit working but I was able to get it to the dealership and get a reading. There were two codes: p3102-581 and c2301 -40 and 50. the dealer wants to keep it all day to "dig into it". This is on a 2006 prius.
View 19 RepliesYesterday I got the "red triangle" and check engine light along with these 3 codes:
P0A80 - replace hybrid battery pack
P3019 - battery block 9 becomes weak
P3000 - battery control system
In April of this year I have the entire battery replaced, in September I got the triangle again and one cell was replaced under warranty. My warranty is good through April 2016, however I'm afraid that this new code P3000 is going to be something not included in my warranty.
What could potentially be wrong? This is a 2006 Prius with approximately 208,000 miles. I'm not sure this is worth it anymore especially if I have to keep putting in more money.
ok scan system for code with Snap On verus and a Launch x431 this is a 2005 with 192k. I can not find any inf codes to lead me in the flow chart that alldata provides. Are their some years that don't provide inf codes. I have check all 3 smi relay and they are getting the command signal to closed the relays but looks like the smi2 will not close at times can this be the cause of poaa6 of the isolation fault. seems to be intermittent sometimes it closes. As far as the poaa6 I did push the start button 1 time to power up with no not "ready" on and waited 90 seconds and the triangle came on and set code. It has a new 12v battery I have take all the buss bars off the hv and clean, not that bad very littler discoloration and corrosion. Test each cell and have 7.78-7.97 in each ,installed 55w light loaded each and none ever drop below 7.65. this my not be the right way but I am learning and trying to figure this out. Have really never worked on the hv side of a prius always the motor side, but this now intrigues me .
View 9 RepliesI have a 1999 B4000 V6 4.0L with 78K miles on it. I recently had P0171 and P0174 error codes come up. I replaced the MAF sensor and have not had the codes return but now the truck will basically stalls out when sitting at a stop light. It does not do it all the time just randomly. It has never done it when engine is cool but only once up to temp. The idle is smooth at cold engine but begins to get rougher once warmed up (nothing too bad just noticeable). I cleaned the IAC with MAF cleaner but no joy. I reseated all plug cables at the coil but no change. RPM around 600-700 then fluctuates up a bit then truck will stall quickly( I usually cannot put other foot on gas in time to get it to increase RPM before it dies)....
View 5 RepliesI was driving my 2008 Prius and it abruptly slowed down and became undriveable. I had all of the warning lights - the red triangle master warning light, hybrid syatem warning light, and the check engine warning light. The car had to be towed home. The gas engine starts and runs - driving forward feels like the brakes are on - will not drive in reverse,. I checked the codes and had the following : POA1D, POA78, POA90, and POA94.
View 2 Replies