Prius (2004-09) :: Died After Replacing Front Brake Pads / Can't Start Afterwards
Jun 19, 2012
I replaced the front brake pads the same method as a traditional car. (Popped out caliper. Pushed piston in. Put new pads in). I did not pump the brakes after installation (forgot to do so).
I drove off to test drive. A block later as I approached a stop sign, I smelled something similar to burning brakes (this might have been some of the oil I spilled when I added oil just before I left). Went to the next stop sign 100 yards away and was able to stop. Made a slow left turn and MFD displayed a warning and ABS (and maybe other ones too) light came on. I pulled over. I don't remember if the car shut itself or if I turned it off.
Now, I can not get the car started. Had car towed home with wheel lift tow truck.
Tried the following:
- Press brake, push Start: Car appears to power up then shuts down immediately. Lights appear on dash, then go out. The squares around P,N,D,R,B are the last ones to go out.
- Press start to go into ACC mode: Radio and clock power up without problems. Pressing start again results in same symptom above.
- Tried to read code with ODBII scanner: all I get is "ERROR". Appears that it's not linking.
View 15 Replies
Advertisement
Ok so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 Replies
2004 prius. I change the brakes on various cars all the time, and never had this problem. After I changed both sides, I started the car, and saw 4 lights:
- Red brake light
- The yellow exclamation light
- ABS light
- VSC light
The car now stops funny, and reading the service manual, it says that if there's a failure detected, that it will revert back to very basic braking (no abs, only fronts, etc..)... As I was exiting off the fwy, I realized this when one of my front wheels locked up, even and I was not stopping very well. Scared the crap out of me.
In any case, I can't see what I may have done which would cause a failure. The only thing I could think of is to bleed the brakes again, but I did this and think it's ok. Is there anything else I can check or is this something I have to get serviced? I saw another thread where they suspected the actuator, but it is somewhat a coincidence that it would go bad after I replace the pads? I'm not sure how the regenerative brakes works on a prius, and whether there's anything I could visually inspect to see if I bumped something???
View 19 Replies
Last week I replaced my stock 2016 Elantra's brake pad's with Wagner Thermoquiet another forum user recommended, came with new hardware (seats), however not new 'plates' (that are on the side of the pads), so I had to reuse the old ones which were quite dirty/ old looking. Anyway, I understand due to the old rotors being on there, I'm going to hear some unusual noise when letting off the brakes until broken in, however, squealing when I press the brakes? (Only happens at low speeds, like drive through window.) I greased all the metal components that make contact with the caliper. I NEVER experienced squealing with the old pads, & these are "supposed to be quiet & more efficient". I'm going to take the wheels off & look at them tomorrow. What I can do?
View 15 Replies
i have the brake (!) the ABS and the VSC lit up after i got new bearings and new brake pads and rotors, the car was also stalling before the mechanic removed these bearing "dust cover" circles that must have been causing speed sensor interfernce bc the spedometer was stuck on 0....so the car seems to be done stalling after those were removed and all the big lights went off then i hit the brakes a few miles later and those three lights came on...
View 2 Replies
I changed the front brake pads, took all the precautions during the change, did not disconnect the 12 v battery, pumped the brake pedal 12 times, started the car and no warnings. Now the brake pedal is a little spongy, if I press the pedal to the floor the VSC/TRAC light comes on, to reset it I have to press on the pedal again and the brakes do work.
View 11 Replies
Having brake pads making noise while driving on war zone like roads? Sounds like the front end is falling off. It started after a front brake job. Dealer then replaced all the clips and it was fine for six months. Now starting to make noise again.
View 6 Replies
I noticed the front brake pads were touching the rotors when I was painting the brake calipers. I had my e-brake engaged and in park. I'm assuming the e-brake only brakes the rear wheels because the front rotors were still movable. Although the car still rides fine but I'm not sure if this is normal.
View 1 Replies
This started recently and suddenly during our recent snow. It sounds like the pads have worn down. Only happens at very low speed, not immediately at the point where the disc brakes cut in (>7mph?). Apart from the sound, the braking action feels normal and it stops fine.
The pads were only replaced a few months ago. Done 106,000 miles now, and no more than 2,000 since pads replaced.
I had thought it might be some grit caught between disc and pads but it would have cleared by now and there are now obvious signs on the disc of anything.
What would I be best to remove the wheels and take a closer look. Also, is there a wear sensor on the pads?
View 2 Replies
Changed my 12 volt today with a yellow top. After starting car found brake warning light on, is the something that will reset when driving?
View 2 Replies
2005 Prius with 190,000 miles.
I was having intermittent problems with my cruise control but realized it would turn on and off if the wheel was turned 45 degrees. I replaced the spiral cable (with a Toyota OEM) and the cruise worked great! The only problem was that the VSC light was on. There was a fault for a steering wheel position sensor. I attempted to do a zero point calibration and now I have the red Brake, ((!)), ABS, and VSC lights on solid all the time.
I've unhooked the battery for hours several times, tried to clear the codes (no obd codes show up), and tired to clear the ABS fault by pressing the brakes 8 times in 4 seconds while in diagnositc mode and jumping 3 and 14 four times in 8 seconds.
View 19 Replies
Today as I was adding pressure to my tires I noticed the front brake pads were wearing unevenly. Both outer pads wore the same. More "meat" on the inner section of pads than on the outer, evenly worn, just sort of slanted down as you move out towards the outer rim of the brake disk.
Is this normal? What would cause this? Should I have it looked at? I've never seen anything but even pad wear, perfectly parallel to the brake disk.
Edit for these pictures to clarify.....
View 24 Replies
Having trouble with front brake pads rattling? About a month ago, I replaced pads - rotors - caliper pins on my 20th GLI. I know these cars ride a bit stiff but it sounds like my front end is about to fall off. All brake parts were torqued to spec - I've gone through all T25/T30 torx front end screws etc and I just can't find the rattle??? This has only started within the last few days. Any other places to check for obvious loose bolts etc?
View 15 Replies
The front pads on the R shift from one side of the caliper to the other whenever I move from forward to reverse they make a loud "clack". I thought it might be an O.E. pad issue, but I've changed the pads out to EBC's, but still no bueno. The new pads fit snuggly into the calipers and seemed to have solved the problem at first, but about 5k km's in, they're making the same noise.
I have anti-rattle springs installed, but they're not working. Is there supposed to be a pair of shims between the caliper sliders and the pads grooves that the previous owner removed for some reason? I don't think so, because that car only had 25k km on it when I purchased it; but you never know.
View 12 Replies
Just got out of the dealer they said they recommend front brake change. They quoted me for ~730 just for Rotors/Pads/labor on the front (I am going to shop around).
I tried search Golf R Brakes info prior to posting but alot of the searches are for people buying Golf R brakes for Gti's.
1) Do I need to Replace Both Rotors and Pad at the Same time?
2) Currently Car is still stock and see's no tracks, the most car would see in the next 2 yrs would probably be stg 2+ if that. Would OEM Rotors + OEM pads be sufficient? or should i upgrade pads? Below is listing i found with some different pads options.
[URL]
3) Car is currently a 47.5k miles with oem brakes, should i just replace rears as well? even though dealer did not recommend?
4) SS Brake Lines, should i get them?
View 7 Replies
I know on some cars and trucks you need a special tools to push the caliper back in. i just use a large c clamp to do the job. Question do i need any special tools to replace the front brakes pads?
View 7 Replies
Scion TC for Camry SE 2007.
I changed the front brake pads and resurfaced the rotors. After putting everything back together, I took the car to test drive it. The stopping power is fine and there is no squeaking or robbing sounds. However, when I apply the brakes at lower speeds moving forward there is knocking sounds the comes with the tire rotations. What is the reason for this sound?
This is my second time changing the pads and rotors, with the first with no issues. I put grease between the shams and the pads, and I sprayed the rotors with brake cleaner before the installation.
View 8 Replies
I replace the frond brake pads. Press the piston caliper using a c- clamp. When my brake job is done, start the engine, pump the brake now the yellow light come on.
View 4 Replies
I have about 50,000 miles on my pads, they look 50% gone, but couple days ago I've got short "beep" and light yellow came on(circle with several small parts of larger circle). What and why? Rotors, pads, other?
View 4 Replies
05 Camry, 2.4L, 47K. Replaced the front brake pads two months ago. I put in Akebono pads and did nothing with the rotors as the original pads were not completely worn out and there is no vibration whatsoever in the pedal.
The pads have recently started making noise on brake application. I'm getting ready to take them back apart and re-lube everything. Should I take some sandpaper to the pads & rotors to knock off any glazing? Do I hit it with a course or fine grit? I have not had this problem happen in the past and was thinking that maybe it is the quality of the pads but I believe these are oem...
View 1 Replies
The gist is that my 2006 Prius would not start, even with an attempted jump, and now the dealer (Keany Mesa Toyota in San Diego) says the total cost of repair will be $2400 for a new junction box relay and water pump ($800/$2400). I am stunned at the cost and am questioning the need for both jbr and wp -- but apparently, wp is leaking. About a year ago, the expensive battery was replaced, luckily under warranty , so no cost. Don't know if jbr, wp and battery failures are related, typical repairs or we just have a lemon or getting ripped off. is the water pump recall from years ago relevant here? Should we get a competing bid from a non-dealer/Prius expert (is there one in SD, a search of Prius chat found 1 recommendation but it was rather weak), or just get the damn work done and have a stiff drink to deal with it, or maybe it is time to get a new car - Prius or other (what's the chance the dealer give us a good trade-in deal?)
View 17 Replies
