Prius (2001-03) :: Random Misfire Codes With A Burnt Smell - P3120
Jan 18, 2016
2001 Prius (242,044 miles) with transaxle error code! Red triangle with exclamation mark, check engine light, PS error, Main battery error, and little red car with exclamation mark error. One week ago car gave random misfire codes with a burnt smell... could have been from my car or could have been a smell from the car next to me. Cleared codes and they never came back. This week I get the CODE OF TRANSMISSION DEATH the dreaded P3120 along with a 5 minute wait by the side of the road until I could restart it and drive the 5 miles back to the house. Cleared the code but it came back the next day with another total loss of power and another 5 minute wait on the side of the road.
After I turn off the car and wait a few minutes it will usually start back up and I can continue on my way... sometimes for a few miles and sometimes for 10 miles. My question is this... could this problem be something other than a bad transmission (transaxle) or should I be looking for a used transmission on ebay? I have also heard that it is possible that the MG2 might be bad and that it can be swapped out without pulling the motor so how can I test and confirm my real problem. I plan to repair myself one way or another... Other than all these warning codes and exclamation mark warnings symbols she drives great until she stops producing power and coasts to a total stop.
View 12 Replies
Advertisement
Trying to troubleshoot my 2001 Elantra (173k). I'm having intermittent trouble codes being set and I'm wondering if they may be related:
P0302
P0303
P0446
The cylinder 2 and 3 misfires are relatively recent. Plugs and wires are visually ok (and not that old). I swapped plugs 1 and 4 with 2 and 3 to see if the plugs are bad. It took 3-4 days, but the P0303 set again (and it's very intermittent - car will noticeably lose power for a few seconds, code set, then run fine for several days). I also sprayed carb cleaner on the intake manifold gasket with no change in engine idle, so the gasket appears to be intact.
I had read in a forum somewhere that the misfires could be related to a vacuum leak, which could also be setting the P0446 code. I removed the charcoal canister and inspected the lines - visually ok.
I bench-tested the canister control valve and it did operate, though I noticed some charcoal blocking the valve so it would not close all the way when energized. I used compressed air to blow the debris out of the valve and it appears to close properly now.
I went to hmaservice.com and noticed there are no instructions for the P0446 DTC. I've been using a Haynes manual instead. For quite some time now when refueling, the fuel nozzle shuts off every few seconds (I have to slowly put the fuel in to avoid).
Some questions:
- Can these codes be related?
- Based on my symptoms, should I replace the canister control valve? What about the charcoal canister and the charcoal air filter - should those be replaced as well?
- What else should I check?
View 9 Replies
I bought my Prius after I tested the car around town and on the highway and went smoothly. I drove the car about 200 km after the warning came on board, high temperature and cold engine warning (red and blue). Stopped the car and I found nothing to be hot (engine or inverter).
I rebooted and the errors disappeared but reappeared and on the highway (120 km) car no longer accelerate, pedal did not respond.Stopped and restarted repeatedly trying to get as close to home and a Toyota service. High and low temperature have appeared and disappeared after stopped and restarted. Warnings appear together, none or only one of them.
But after 600 km appeared turtle on board and the car stopped. I was unable to start. They came from Toyota and were able to start with another auxiliary battery and ran 10 km with a tester on the dashboard (at full throttle and the car accelerated 1 km / sec until it reached 60 km / h then accelerated normal to 125km/h. When he put the foot on brake and after that tried to accelerate again the pedal was non responsive and the car stopped again and they towed it.
Next day they told me that the ECU is faulty (the one located behind the glove compartment) together with the Auxiliary Battery.(1100 Euro ECU).They told me that the temperature sensor is 200 degrees Celsius with a cold engine.
We towed the car to another service closer to home (1300 km) and asked a second opinion telling me that is defective inverter. I decided to buy an ECU. (220 Euro/ second hand)
Meanwhile my traction battery died after they tried to start the car many times.
After I charged the traction battery (one module at a time), whole battery shown after charging 301 V.
Now I have the following :
P3120 HV transaxle / Wire harness
INF. Code 249 (Open or +B short in motor temperature sensor)
View 19 Replies
Working on a 2002 prius with 153k miles. bought it with a "Bad transmission" diagnosed by toyota dealer. Got I home and did a quick check but there were no codes. I drove it about 50 feet into my garage where it would shudder badly while being driven which from my experience sounds like a bad MG2 motor. Drained the oil and thought hhmmm th oil does not smell bad and neither did it look burned. Proceeded to pull the mg2 but found it looked brand new, no burned spots or any such thing. SO I put it back together and think its a bad invertor. put on a different invertor that I have lying in my garage that I "think" is good and start the car. get code p3125 and p3120 and still have the bad shuddering when i try to drive it..Is there any way to test it further before I pull the trans and put a new trans back in?
View 19 Replies
Had this code show up after the warning light came on and then the light went away after two day, the car seems to be a little sluggish now. I have read that this is a random engine misfire and it could be a bad plug..
View 1 Replies
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 Replies
Yesterday, i changed the spark plugs, spark plug wires, mass air flow sensor, air filter and replaced the in and out take coolant lines in the throttle body.
Before yesterday, i got random misfire codes that would clear and return, i have no a/c, i believe the thermostat needs replacing as the van runs hot after a while of running and quickly when idling and the upper radiator hose is hot. The van's idle is rough to the point that some one else turned up the idle so it would stop stalling so frequently, especially in reverse. it stalls very very rarely now.
then a few days a go i got a knock sensor code that clears itself and then returns.
A friend changed the distributor cap, and noticed some melting and corrosion, hence the spark plug and wire change. this friend also pulled the wiring harness for the front 3 injectors while it was running. the one on the far right created no audible engine change (also this spark plug was immaculate compared to the others), so he said it is bad (or is my friend a moron?)i had also noticed a coolant hose that would spray coolant when really hot.
So yesterday i tackled the above. In the process of doing this i had to rip the other coolant hose to remove throttle body, i replaced these with a self cut piece of 1/2 heater hose. after removing throttle body, i realized i needed a gasket. so got one of those.
a few notes:i used antisieze lube and dielectric lube on spark plugs, thread and ceramic respectively. the mass air flow sensor is used.i cleaned the throttle valve with brake cleaner (non chlorinated) because it was nasty! i did not remove the cables attached to throttle body, just moved it out of the way while working.i hand tightened everything.there were 2 skinny hoses i disconnected, one with a metal tip that went in to the large rubber air intake hose, and one that ran into the throttle body (this hose ripped like a 1/4 inch off it seemed long enough, so i did not replace). i disconnected the large air intake hose at 3 spots with pipe clamps.i disconnected 3 wiring harnesses 2 at throttle body and 1 at mass air flow sensor
Now, it seems the van is running smoother while getting gas, but rougher when idling. What did i miss? what would be causing a rougher idle? I am now at work, i will not be home till around 9 cst. So I cannot check anything.the van did throw another code, but i have not checked it yet.
View 1 Replies
My 07 3.3 SF is throwing P0154 and P0300 codes. Autozone said the P0154 is Bank 2 pre-cat O2 sensor. But exactly which one? The P0300 is random misfire. Could they be related?
View 7 Replies
I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
View 2 Replies
Toyota read the codes wrong and told me that I need a new hybrid battery. That is incorrect info. Codes P0300 P0301 P0302P0303. The codes mean misfire in cylinders 1 , 2 and 3. I have had injector cleaned in the past new spark plugs. If I drive it it gets warmed up and shuts down. It will restart and run maybe 7 more miles the same. The brake light comes on and I have to restart it.
View 9 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
I have a 2008 Accent Hatchback with 130k+ miles. I got a pretty good deal on it from a fellow who maintained pretty good service and had installed an aftermarket air intake (well, he removed the stock one and put a small, roughly 4" diameter, filter that is open to engine compartment) and all looked pretty good.
At the first fueling, I noticed issue - I had to rev motor for about 30-45 seconds to get it to stay started. Figuring it was an evap issue, I replaced purge valve and gas cap (cap was obviously loose). This did not correct the problem. I did not worry about it to much because with that exception, the car drove wonderfully back and forth to work, etc.....until recently.
Car started "jumping" and being sluggish. Codes came back as random misfire. Plugs and wires are only a few months old. I wondered if it had something to do with fuel so I ordered filter and pump (figured i would replace both since I was going to be pulling top off tank anyways) - this is going to be my project for the day.
Here is the kicker though : I noticed in the past day or so that car has been okay on my short commute to work in the morning and back home in evening. When I went to store midday and was parked on HOT pavement, I had issues right away. Car is very temperamental as the temperature increases. My wife also noted that last night while driving about 15 minutes away that the engine wall was hot enough to be uncomfortable to the touch of her bare foot and issues were abundant.
Once I get to speed in 5th gear, I seem to be okay, no issues (yet). It is primarily during acceleration and mostly during low RPM (low for this car anyways which seems to run best at 2500+).
View 13 Replies
Okay, so a few weeks ago, my tire blew out on the freeway. Of course my spare wasn't in there and when I got one I couldn't get the lugs loosened. My 4way was too big on all sides. It was late, I am a single mother of two young kids so I had no choice but to drive slowly to get it off the freeway. The next morning I came back fully prepared, got my car in to get a new tire. I have been driving with ONE code for my CEL, but at the shop (where I use to work) I used the scanner and it threw 5 codes.
P0300 Random misfire
P0442 Small EVAP leak detected (this one was already there)
P0420 Catalyst system below threshold bank 1
P0301 Misfire cyl 1
P0303 Misfire cyl 3
My beautiful love is an 02 Jetta 2.0 4 Cyl. Now, since 4 of these codes popped up AFTER my first blowout (I turn 30 next month, knock on wood)
Did driving my car at 5 mph about a mile and a half (everywhere up until the gas station was NO PARKING) do something to my car? All of a sudden, any in town driving ESP IDLING makes my check engine light blink and my car has no power I just have to pull over wherever I am. I checked the car out myself on the side of the road and my cat was glowing. After this I do not drive my car.
So, what should I do. I did a tune up. Should I replace the 02 sensors then the cat?
View 24 Replies
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
View 3 Replies
99 F-250 SD 6.8 had an issue with it while moving from Del to Phx, Az. Found collapsed air cleaner element. It looked like someone stepped on it. I replaced it as well as the MAF. This fixed the issue. This was 350 miles into the trip. The truck seemed to be down on power as it didn't want to pull my trailer up any type of grade except with OD off. Around 2K miles into the trip in developed a random misfire with no codes. I am at my final destination and the misfire is worse. I am not showing any codes at all or pending either. It is a bit toasty outside to be out there diagnosing issues, and I won't start changing parts randomly either. I have a NGS scan tool with the proper cards.
View 5 Replies
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
View 2 Replies
I had to park my car in the hot sun on vacation the last two days and when I first crank it up with the AC on I get a familiar burnt wire smell but a little different. It goes away after about 3 minutes.
View 11 Replies
My check engine light came on the other day, with no symptoms or problems. Today I stopped at the Auto Parts store and had the codes read. They were P0440, P0441, P0446, and P0301. They are for the EVAP system and misfire.
I had read here that one of the codes could be for the gas cap so I tightened it and then, also as read on here, disconnected the negative 12 V battery cable to perhaps clear the check engine light. I was curious.
When I started the car again, I now have not only the check engine light, but the red triangle exclamation point. How would you proceed? The 12 volt battery is around 5 years old. The entire exhaust system was replaced last year.(not O2 sensors though)
The hybrid battery was replaced at 70,000 miles and I now have 110,000 miles on it. I really wonder why disconnecting the battery and reconnecting it caused more error lights to appear? Also, the Auto parts guy said his code reader was fine for my car but I seem to remember here that there may be a special Prius one.
View 6 Replies
I'm possibly being paranoid, but twice, after hard driving, my Prius has smelt strongly of burnt plastic/rubber.
View 19 Replies
I have a 2004 prius with about 350k miles on it, bought it about a year ago and we have had our first trouble with it (it's been great so far, and when you consider it's mileage, pretty impressive).
We were driving along and a constant alarm started (beeeeep!!!) and lights on the dash lit up. I assumed it was cranky because the rear hatch wasn't closed or something and kept driving (we didn't have far to go). It wasn't long before smoke with a distinctive burnt electronics smell started coming up from the dash at the front left lower corner of the windshield. Then the brakes started to feel very unresponsive and sluggish (no regenerative braking either). She still runs and drives. So here is where I am now:
The car screams constantly and the brake light, ABS light and the (!) light are all lit.
I've been poking about and figured out that my inverter coolant pump isn't working properly. At this point I am wondering if this is just pure coincidence though (i.e. perhaps its not been working for awhile). I will be replacing this soon.
I checked the error codes and they all seemed to be un-related and or old (catalytic converter not working properly, ran out of fuel, etc). I cleared them and no new ones are populating. (car has only been driven around the block 3 times though)
The 12 V battery seems to be working fine, and it's getting the proper charging voltage. (voltage tested through the console under various conditions)
I have reset the braking system (bridging the #4 and #13 pins thing) and this turned the buzzer and lights off for about 20 seconds. Still no proper brakes. And of course the noise and lights just come back. Still no error codes via my Bluetooth reader and smartphone.
I have my doubts that replacing the inverter pump will fix this brake issue. I am familiar with working on cars, but this is my first foray with 1) a modern car and 2) a Prius. (Previous cars are all mid 90s or older, so I'm a little bit overwhelmed here...)
View 16 Replies
We have been fighting a misfire code for about a year now and I'm pretty sure I finally found the cause. Last Spring the car died on the road and we had it towed to a local service center where they said the fuel pump was bad...this was the 2nd in about 2 years (previous owners doc). We had it replaced and the car was fine but as mentioned had a random misfire code that would come and go. In the last month the car has left us stranded several times and then started after a few hours or a day. While checking the connection to the fuel pump with a meter and test light I verified the pump was getting power correctly to the 5-pin connector but would not start. I unplugged the connector and the 1st 2 pins in the harness connector were damaged and probably burnt.
I cleaned it and applied dialectic grease and plugged it back in turned on the key...fuel pump primed and then the car started and ran fine. It then started to randomly turn on and off but not enough to stall the car. I wiggled the connector and the it I could make it run or shut off. Obviously the connector is bad and the contacts are intermittent. While driving the vibrations would move it just enough to make it cut on and off and more than likely cause a misfire code and sometimes stall the car. My problem now is I can't find a replacement connector/pigtail for the harness connector anywhere including the dealer. Where can I get a new connector for the 5-pin fuel pump harness connector? I have found a MAF replacement connector that looks very similar but not 100% sure if it's the same.
View 1 Replies
