Prius (2001-03) :: Cylinder Misfire P0300 - Error Has Been Occurring Almost Daily
May 19, 2012
General misfire when the engine light comes on. This error has been occurring almost daily, sometimes it pins it down to cylinder 3. My wife's nephew who is a mechanic says it could be the sensor, but I have only been getting around 30 mpg though the car seems to run alright. I did go ahead and get the plugs replaced, as I was told it could be a bad plug but the error light still comes on as before and the mileage appears no better. What could this be? I am retired on fixed income and dread the very idea of an expensive diagnostic & repair session with a dealer service. Their solution for about everything wrong has been to replace the gas tank (three times already in the life of the car). Last time that did not fix what was going on with the car..
View 10 Replies
Advertisement
So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.
View 3 Replies
Had this code show up after the warning light came on and then the light went away after two day, the car seems to be a little sluggish now. I have read that this is a random engine misfire and it could be a bad plug..
View 1 Replies
2005 4cyl. Vue with 54K... Steady CEL. Runs great. Absolutely no problem accelerating. Don?t hear or feel any misfiring. There is a slight rumbling sound when I first start to drive the car, but to me, the sound doesn't seem come from the engine, but rather underneath the car. It goes away when I continue to drive. Since winter began, I occasionally feel a very slight hesitation during idle?happened once or twice lately.
Again, I only feel justified in mentioning it simply because of the codes that were generated. None of my passengers have made a comment about the idle or the drive. My friend, however, made a remark that occasionally, there is a very very very slight hesitation at the downshift when braking. No crack in gas cap. Great fuel economy. No problems accelerating at all. Never hear or an actual misfire, which I take it, means a problem when accelerating, a jerking, or popping noise.
Took it to a dealer. Codes were 0300, 301, 302, 303, 304?302 generating most often. Dealer recommended new ignition module and plug replacement, but they said it wouldn?t be a guaranteed fix and that it may need EGR replacement (don?t hear knocking though) or be a burnt valve in the cylinder. No suction out tailpipe, no rotten egg smell (signs of burnt valve). What are the chances of burnt valve in a car with 54K anyway?
Also, my maintenance schedule claims that I don?t need new spark plugs until 100K. Is there anything else this could be such as a dirty injector system, fuel filter, fuel pump, or air filter? Again, overall, the car runs GREAT! Should I just wait and see if the misfire becomes more pronounced so when I take it to a mechanic, they won't be looking for a needle in a haystack?
View 4 Replies
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 Replies
I have a 2001 Ford Windstar Sports SE with 155K miles. I did a tune-up eight months ago. With the tune up I had to replace the fuel pump because it was defective. Later, I found that there were misfires occurring since I was getting slow acceleration. I had the spark plugs on the guilty cylinders replaced again and the spark plug wires.
Periodically, I have had to return to the shop to have the vehicle checked. I sometimes get a blinking check engine light while trying to accelerate, which now occurs only while it is raining or I am exiting the car wash. The shop is at a loss as to what it is (spark plugs and wires are fine, no lose connections noticed). I am wondering if I should take it to someone else. Of course, taking it somewhere else will cost me $100 to check on someone's else work.
The shop replaced the ignition coil. Distributor cap is fine. They keep saying that the engine is running fine while in the shop and do not get any codes. I had them drive it while it was raining and they discovered that cylinder 4 is misfiring. They worked on the cylinder. The vehicle runs well, until it rains or I wash it.
My questions to the group, "If everything is OK, how come it is misfiring? What are they missing? What is the connection to the moisture?"
View 14 Replies
The check engine light keeps coming on and off on my 2001 Echo with the above code. The car runs fine and the check engine light randomly comes and goes. What would set off the check engine light, but not cause noticeable change in performance?
View 2 Replies
I have a 2004 Hyundai Santa Fe 3.5L V6 when i was driving a couple of days ago the check engine light flashed and after a while it stayed on the codes are P0300 which is a random misfire as well as a misfire in cylinder 2, 4 and 6
I replaced all 6 spark plugs and the 3 spark plug wires still the same issue. The car hesitates when accelerating when i accelerate it looks like it wants to stop the rpm goes to almost zero and then it moves and so on. the rpm goes up and down like crazy.
Sometimes it won't move past 1000 rpm I'm moving 60mph and still on 1000rpm and sometimes it works just fine like there is no issue at all. When idle the car is fine and everything seems normal it stays on 900rpm. The car has 158K miles on it.
I uploaded a video to show you what's happening to the tachometer when I accelerate [URL] ....
I'm on a limited budget I'm thinking of changing the ignition coils but i want to make sure that's what is causing the problem first because i spent 200$ to change spark plugs and wires and the mechanic didn't fix the issue.
View 13 Replies
Mystery issue with my 2001 Accent GSI (5-speed manual, 1.6 L). I'm getting a P0300 error code and the Check Engine light (the light is like an old friend, I miss it when it's not on). This happened four months ago and I replaced the ignition coil - seemed to fix things - but now the light and the error is back with a vengeance. Car stumbles and runs rough. Changed the plugs and plug wires, but no difference.
BTW, there's a small pin hole in the upper part of the gas tank (just enough to give it a gassy smell when the tank is full) but I don't think the hole would be big enough at this stage to cause the check engine light to come on in the same way it does if you leave the gas cap off or loose.
View 3 Replies
I left my chevy s-10 truck sitting over the christmas (23/24/25) and it was really cold outside and when i got back i started getting a P0304 (Cylinder 4 Misfire). I replaced the spark plugs and spark plug wires. May be the cold would cause this to happen? I think I've noticed the trucks fuels efficiency drop over the past month). May be the fuel injector(s)? Is the s-10 TBI or does it have fuel injectors for each cylinder?
View 8 Replies
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 Replies
The car has an obvious misfire and the scanner says its Cyl # 8. I tried the "italian" tune-up and under heavy throttle the miss goes away. I swapped coils and the miss stays with Cyl # 8. I pulled the injector, and can't see anything wrong.
View 11 Replies
2006 PT Cruiser Touring Ed. The engine light came on 2 days ago, had it looked at today and the error code p0304 "cylinder number four misfire" was diagnosed. What causes that and what would need to be done to fix that problem?
View 9 Replies
Getting error code p0302, misfire in 2, pulled the plug and had oil on the treads and on the lower part. My guess is the valve cover gasket, but I'm not 100 percent sure.
View 18 Replies
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
View 7 Replies
So driving on the highway my car died. It would crank but not start. Got it towed. This is what I have done to troubleshoot.
1. Swap ECUs. The car should start for a second and shut off because the car doesnt match with the ECU. Still just crank and no start.
2. Fuel pump still primes when I open the door. I also hear a weird air leaking noise when I reconnect the battery, but I think it comes from the fuel pressure regulator (which I think is normal).
3. Checked for current at the ecu wires, wasn't sure what to look for but it was getting numbers.
4. Battery had 12.1 volts running through it (Haynes said 12.5 but is that really much of a difference?
5. Checked spark plugs for spark. Pretty sure we did it right, but there was still no spark. We tried multiple times.
6. Scan car, get code P01314 twice (ECM error).
7. Try to clear codes, says Comm error.
Why am I not getting spark? and why is the ECU error occurring, because we tested with a new ecu, and there was still no start, not even for a second like there should be.
View 12 Replies
Recently i started the car and it was shaking more that usual. the CEL light came stating P0300 with random misfires. It sounds and feels like misfires so i believe this is true.
View 10 Replies
I hookup an OBD2 tester on my Prius 2014 Plugin and saw the OBD2 P0300 - Random Misfire. I did a reset and the error still came on. I also tested my friend Prius 2014 Plugin which is factory stock and had the same error. Wonder if that is by design or not. Going to take my ride into the dealer on Friday for my 25K maintenance and have them look into that error. P0300 can be anything. Hopefully doesn't cause more problems down the run..
View 3 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
I was driving along and the engine started missing really bad. The whole car was bouncing around. At first I thought I had a flat, but when I stopped I noticed it was the engine. I checked the error codes and got 16684 and 16686 --- Random/Multiple Cylinder Misfire.
I had a problem recently with the vacuum hose broken and was causing an error code. Replace the hoses and it has been fine. Checked to make sure that the hoses were secure and they are fine. Doesn't seem to me to be related. So many problems for a car with 57,500 miles
View 6 Replies
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
View 7 Replies
