Suddenly today, I get a "Check Engine" light while driving. Scangauge II says it's a P1430 error. I found two different suggestions, but where these are located on the car.
P1430-Electric Air Pump secondary Failure
P1430 -Vacuum Sensor for Adsorber and Catalyst System Circuit Malfunction
I just recently purchased a 2001 Prius with 92,000 miles on it and the check engine like comes on frequently. I have a scangauge and I scan for codes and it comes up P0000. I clear the codes the light goes off and everything seems to be ok. I'm not even sure where to start "looking" for something to be wrong.
View 17 RepliesI have had a 2002 Prius since December of 2012, and it has been running fine since I got it; while it was in a wreck in May 2013 that has rendered both passenger-side doors and windows unusable, I have not seen that incident cause any other problems, and the car still runs perfectly fine. I am supposed to be driving from my current home state for a job soon, but about a week ago while I was driving on the interstate, the check engine light started flashing.
I was changing lanes and putting a good bit of pressure on the gas in order to pass someone that was going below the speed limit, putting my speed at around 80 mph when the check engine light started flashing. I started getting off of the interstate to find a place to stop and inspect things, but the light stopped flashing when I got down to around 45 mph on the exit ramp, and I was able to drive the rest of the way on the interstate without any trouble, even when I got in the 75 mph range again. The span of time between the light starting to flash and turning off again was probably about a minute or so.
I was driving my trusty 2002 152K miles, and came into a very long and very slow traffic jam on the side of a mountain. After about two hours of mostly stop and very little go, my CEL light came on. I am also seeing the "general fault" symbol, but it should be noted that my PS symbol has been showing for about a year because my PS died and I just didn't fix it.
View 11 RepliesI have a 2002 prius with 143,000 miles. On Friday, I went to start my car and put it in gear and the check engine light came on and the "triangle of death" lit up and car died. I turned it off and waited about 30 seconds and tried starting it again. It started and I drove 1/2mile home. Went into the garage and got the Actron/OBDII code reader. Pulled the code P3125 which when I googled it, it was referring to the inverter. I cleared the code and all was well.
View 6 RepliesI have a 2001 Prius with 210,000 miles. The inverter and traction battery were replaced last year. I started getting triangle and check engine lights about a month ago and the scan tool read p3191 p3006 p0300. The car would barely start in the mornings and the dash lights would be dim. I replaced the 12v aux battery today and all the symptoms went away. Driving home the triangle/check engine light popped on again and I stopped at Orielly's to use their scan tool. It now only reads P3006. I called a local mechanic who suggested to drive it a bit and clear the codes because the battery needed to equalize. Is this true?
View 8 RepliesI have a 2003 Prius, I had an accident and after it was fixed the check engine light started coming on. It would go off after a couple of days. The first time I took it to Autozone and the codes were P3150 & P3130, but the next day the check engine light went off. A couple of days later the light came back on....went back off....next week it stalled on the highway, but it started back up, now the codes it's reading are P1636 and P3002. It still starts up and will drive, but I'm afraid to drive it.
View 2 RepliesMy check engine light came on the other day, with no symptoms or problems. Today I stopped at the Auto Parts store and had the codes read. They were P0440, P0441, P0446, and P0301. They are for the EVAP system and misfire.
I had read here that one of the codes could be for the gas cap so I tightened it and then, also as read on here, disconnected the negative 12 V battery cable to perhaps clear the check engine light. I was curious.
When I started the car again, I now have not only the check engine light, but the red triangle exclamation point. How would you proceed? The 12 volt battery is around 5 years old. The entire exhaust system was replaced last year.(not O2 sensors though)
The hybrid battery was replaced at 70,000 miles and I now have 110,000 miles on it. I really wonder why disconnecting the battery and reconnecting it caused more error lights to appear? Also, the Auto parts guy said his code reader was fine for my car but I seem to remember here that there may be a special Prius one.
I own a 2009 Prius (4 years and 4 months old) with about 33K miles on it. Last Sunday while driving the Check Engine Light (CEL) suddenly came on. I made it home and started digging for possible causes - everything from a loose gas cap to a failure in the water pump for the inverter to a 12V battery nearing the end of its life. I've eliminated the water pump for the inverter as the source of the problem since, when I put the Prius into "Ready" mode, I can see movement in the fluid reservoir (when the gas engine is not on) indicating that the pump is working (it had also been replaced under a recall on that water pump a couple of years ago).
I'm down to a loose gas cap (which I checked and tightened) or the 12V battery as possible problems. I've tightened the gas cap but the CEL won't go off and I'm about to replace the 12V battery. Will that clear the CEL? I'm going to take it to a mechanic on Friday morning (my first opportunity - until then it's sitting in the garage) to get a code readout. Could this be something more serious? I mean the car is under 5 years old and has only 33K miles on it! What else could be causing the CEL to light up?
2008 Prius. I just passed by 5K oil change by a 50 miles or so, so my maintenance light was on, but when I was driving it on the expressway today suddenly the red triangle light and check engine light came on, I immediately pulled over onto the shoulder and had it towed. These are the error codes that were showing up:
View 1 RepliesCheck engine light on and code is P1451. I have been told its one or all four things:
1. Gas cap,
2. Evap Canister vent solenoid,
3. Evap purge solenoid,
4. Evap canister.
I am trying to fix this problem on the Taurus. I have changed the Gas cap and this did not solve the problem. The other three things on the list: Are these three separate things? Or are they part of the same thing?
It just so happens that I got my letter from the DMV telling me I needed to get my new tags, and this is an emissions test year for my car. I was buys the last few weeks so I figured this would be a good week to do it. Yesterday.......check engine light comes on. How does that happen???
So now I'm on a time crunch. I went to Advanced Auto this morning and they checked the code. It's P0440, an Evaporative Emissions code. Any thought on what that me be, or any checklist as to what to check first? I'm fairly handy, but know nothing about cars. I'm sure I can figure it out with some instructions.
Summary: Got a check engine code of P0440, Evaporative Emissions. On a time crunch because I need to get an emissions test done. I can probably fix it myself with some direction.
I have a Toyota Prius (2010), and the car has run for about 2800000 kilometers. One day when a was driving my Prius the engine light suddenly get on. So I went to a car car mechanic, he checked the car and told me there was an error code (error code: P0401, exhaust problem (exhaust recirculation flow).
So I bought a liquid that I put in the gas tank, the liquid would clean the exhaust pipe, but the engine light was still on. The engine light is usually on at least 2 weeks, then disappear for about 2 days and come back in two weeks…The car is driving normally without any problems.
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
I have a 2002 Toyota Camry V6. The warranty expired in Feb 2007. The car has only 67,000km.
The check engine light came on and the code is P0770, Solenoid E malfunction. The problem was first reported at 43,000km, when the car was still under warranty but only a transmission flush was performed and the code was reset.
I wrote Toyota and after almost two months they told me they do not cover it because is out of warranty and I do not qualify for the Goodwill program. I tried again to tell them that instead of fixing the root of the problem they temporarily covered it, but again I got a NO. No comments about the mileage, time, etc. Just the car is out of warranty and I'm out of luck.
I have a 2002 v6 Camry with over 270k on it. Today the Check engine light came on while driving on the freeway. When I got home I used my scan tool and it gave me the following codes.
P0128, P0440, P0446 and P0440, P0441, P0446 pending.
I understand that the 128 has to do with coolant temp and that the other codes are evap system related.
What I'm trying to figure out is what might have caused them to all occur at the same time. I know once with my 98 Camry it threw a P0125 which had to do with coolant temp issues but it also threw several other codes for a bad 02 sensor and the 125 was just a false code (replaced the 02 sensors and they went away). If this 128 is possibly a false code or if I also have a bad thermostat/sensor on top of an evap system issue.
Also. coolant level is good and I checked the gas cap and insured it was on tight, reset the codes and am waiting to see what comes back.
My Check engine Light comes on with a P0410 Code. It used to come on every 6 months and I would get it cleared. Now it is coming on about every month. I can't find much about it. Is this something I should get fixed right away. where is it located?
View 4 RepliesCheck engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 RepliesI own an 04 Hyundai Elantra with around 196,000 miles on it, and have run across a problem I haven't had to deal with before. A few days ago, my check engine light came on while driving. I didn't really notice much, but when I started it again it began idling roughly. I got it home and pulled the code, which was P0341 (camshaft position sensor). This isn't the first sensor I've had go on the car (I replaced an oxygen sensor and throttle position sensor a couple years ago), however I ran into two problems:
1. How likely is it that it's the sensor that's bad as opposed to something like the timing belt or VVT adjustment?
2. Since the sensor isn't horribly expensive, I decided to try replacing it, but I can't get any socket to fit on the bolt that secures it. I've heard it's a 10mm, but nothing seems to fit snugly. Maybe there's just so much crud and corrosion that it's ruined the head. I tried using an extraction socket, but no luck.
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
I just got this very nice Elantra 04 with 64k on it. Yesterday suddenly I got the check engine light on. Today I went to Auto zone and they have checked my car and it showed code P2626. But there are more than a few suggestions about what could be. I don't know what to do. See the attachment below.
View 1 Replies