Pontiac - Grandam :: 2000 - Replaced Key Lock Cylinder Now Beeps As Key Left In Ignition?
May 16, 2012
I replaced the ignition key lock cylinder on my 2000 Pontiac Grand Am SE. I performed the re-learn process by cranking the engine over, then releasing to the ON position for about 9 minutes. During the 9 minutes the SECURITY light blinked the whole time, then at the end it went solid for a few seconds, then off. On the next cranking cycle I was able to start the engine and thought all was good. But now when I open the door the car beeps as if the key is left in the ignition and the automatic locks are disabled with the door opened.What is the problem and how do I fix it?
View 1 Replies
Advertisement
I have tried all the tricks on the internet and still can't get the key unlocked, so I am ready to just replace the part. Is this something my son can do or is it very complicated?
View 1 Replies
I have had this car for sum yrs never had any problem a couple months back while driving it would just shut off. Well come to find out my ign fuse would be blowing. I would replace it and it would start up and run just fine. Since then my daughter owns the car and it happened again and she replaced the fuse and it started up fine but while out of town it just shut off and now even if you replace the fuse it just blows. Just as you turn the key, it blows. So i did sum research and replaced the ignition switch. Tryed to start it and it still blows so im at my wits end. If I knew what every component that fuse ran , i could figure it out by process of elimination. I have the Chilton book but i still can't seem to find what all components that one ign fuse runs. It is a 94 grand am 3.1 v6....
View 7 Replies
I have a 2003 Pontiac Grand Am it will start once but after that if you turn off ignition it will not start again until it has sat for a long time.
View 1 Replies
My grand am began shaking (shuddering) consistently yesterday morning and I ran a diagnostic reading on the car. It told me that there was a misfire. I replaced the spark plugs and still no change. This car has been a nightmare to do maintenance work on since everything is either within a case or impossible to access on a regular car jack - so what could be causing this reaction in the car? Is it definitely the ignition coil? I would just hate to attempt to replace that (not to mention the fact that it's $100+ for the part) if I didn't survey other options. 2003 Pontiac Grand Am 2.2....
View 1 Replies
I have a 1997 Grand Am GT and plan to replace the ignition lock cylinder with a used one. If I change the lock tumblers to accept the old key, can I avoid having to reprogram?
View 1 Replies
I bought my 2000 F-250 CCSB a while ago and it came with 2 keys - one for the ignition, and one for the doors/tailgate - may not seem like a big deal, but it annoys me to no end.
From my understanding, the truck had previously been stolen and had the driver's side lock punched, and then something happened to the ignition lock to where it had to be replaced - hence the different key. I finally got around to replacing all the locks so that I'd only have one key. I started with the doors, then moved to the ignition (which I thought would be the easy part). I've replaced several cylinders before and I know it should be simple, but for the life of me I can't get the cylinder out!
I push the detent, turn the key to run, wiggle and pull.... nothing. I can feel the detent push in, and the cylinder will move a little, but it won't come out. I'm not sure if this is something that just happens sometimes and there's a fix for it, or if I'm in a unique circumstance and my column was somehow damaged during the theft and that's what's causing it.
View 1 Replies
About a week ago I was driving my Pontiac 2003 Grand Am V6 and it began to violently shake and the "check engine light" came on and started blinking. I then immediately took it to the mechanic It has been with the mechanic for 6 days and they were unable to locate the problem. They called me today and I was told that I have no compression in one of the cylinders (I have done business with them before and felt comfortable in that I wasn't being taken advantage of). Also, is there any problems in the future with getting a cylinder replaced i.e. other parts of the engine that might correlate?
View 17 Replies
So, I got my explorer about 3 months ago and it has never locked, the door ajar light was always on and I fixed that by using some WD-40.
Now that the door light is off, the explorer beeps once when i lock it using the key fob but it doesn't actually lock. When I use the lock switch in the rear (by the spare wheel tools) it will lock and unlock. The driver's door lock switch won't lock or unlock, the passenger will unlock but won't lock.
Stock alarm system.
View 1 Replies
I am hearing a weird knocking with every rotation of the left front wheel and I know it is not the cv joints. I replaced the wheel bearings on the car a week ago . I think it maybe the brakes have got loose and hitting the rotor or the wheel might be loose but I'm not really sure and it knocks faster with acceleration.
View 7 Replies
It's cold and of course when I need it the factory installed key fob doesn't work. I took the car to one of those fancy car accessory stores and they said my alarm was working just fine. The power locks work fine when locking the car from inside the car. Just not using my remote fob. Searching Google I found an article about a similar condition where they said the solenoid was faulty and this was common for my model.
I know little about cars but this sounds expensive. What is a solenoid and why just the car fob. What is the point of having a remote start if you can't use it in 18 degree weather.
View 5 Replies
I have a 2000 grand am Gt with 3400 motor it started up just fine went to turn around in the drive way the dash lights came on where the ABS sensor is bad, but if u shut it off and started it back up they would go out so i shut it down and went to start it back up and all it does is click, so i thought it was the starter and replaced it, still only clicks. I called GM dealership they said more then likely it is the plastic piece the ignition switch goes in to so i just replaced it and does the same thing.
View 8 Replies
My wife has a 2000 Pontiac Grand Am, as seen above. The car recently started having issues, especially when cold, where the RPMs will rise when in gear but the car will not accelerate. It happened from 25 mph and lower while in a subdivision as well as around 45 mph on city streets. I have a feeling this is a transmission issue, but don't have much experience when it comes to transmissions.
View 6 Replies
I m having trouble figuring out why the radiator fans wont turn on, Even when the ac is turned on it still doesn't turn on, I changed the coolant temp senser. still nothing, i also ran a whire from the battery to the fan and they both turned on. I also stitched around relays and checked fused still nothing. 2000 pontiac grand am 2.4L engine 4dr auto trans.
View 14 Replies
I have just replaced an almost new oxygen sensor on my 2000 Grand Am. After about 40 miles, the check engine light came back on again. I have not had a chance to check it, but I assume it is the oxygen sensor again. What am I missing?
View 1 Replies
My wife's 2000 grand am 2.4L engine is acting really funny. this is the first problem we've had with it. i was driving it to pick up my kids from school. on the way i stopped and got some gas from the marathon then drove about 5minutes and it started running really ruff lose of power wouldn't go above 30mph seemed like the transmission took longer to shifter to.
i made it to the school as i was about 2 1/2 blocks away. got my kids check the oil and it was really low so i got 2 quarts as it was a gas station in walking distance. i thought it was a lil better but i started driving it and it had the same results. i got it home about a 10minute trip regularly and parked it.
the next day day it ran then stumbled hard. and every time i tried to start it got the same think was like a lock up. it did crank but when it tried to start it stumbled or locked up. i pulled the plugs had some wet threads oil was on the first on and the threads and around the spark plug b4 i pulled it out.
2 of the other plugs had red stuff on them not on the threads though. here are some pictures also i will show a vid of what its doing. i did a compression test and here are the numbers starting with the first one with oil on threads.
190-194-200-190+ compression test with cold engine.
Also smoked puffed up not sure from where yet..
View 19 Replies
The Change Oil light was illuminated for a short time on my 2000 Grand Am. This morning, on the way to get the oil changed, the Service Vehicle Soon light came on also. After the oil change, the Change Oil light went off, but the Service Vehicle Soon light stayed on. I stopped by my mechanic, who doesn't like to change oil, since it does pay enough, and he said that there was something else that they should have done to reset this other light. He said it was in the manual, but I don't find it. How to turn it off?
View 4 Replies
I have a 2000 Grand AM cylin. Recently I was driving when my car started to shake violently. I drove it to the side of the road to a parking lot then it died. I started it up again and is ran but shacking a lot again. Once I got home, 3 blocks away the car died again. I tried to start it again but it would only turn but not start the engine. I have checked the gas pump, motor mounts, oil and anti freez for oil. I did check the timing chain but I don't know much on how it should be.
View 2 Replies
My check engine light started blinking on my 2000 grandam se last night and it was missing bad and now it wont start what is it.
View 13 Replies
I have a 2000 Pontiac grand am coupe GT with the 6 cylinder engine. It has been a very good car to me. I really like it and it "fits" me well ... and yet... it is now testing me. About a year ago the check engine light came on. The codes were P0327 and P0336 for bad Knock sensor and Crank sensor respectively. The were both replaced multiple times, the light still stays on... and the codes are still coming up. I have have been to different experts, and after the computer resets... there they are again. (someone even thought that the computer needed updated codes for those sensors... so he installed them.. with no better results). The code P1189 for an oil switch is now coming up too.Here in California, the car cannot pass smog with the check engine light on... so I'm not able to re-register it, and I don't think I can sell it for much because no one can register it now. So, what this can be? Is there some common thread between all these sensors (or a recall of some kind) that would explain this? My fear is that the computer will have to be changed at about $1000. My even greater fear is that that will still not solve the problem.
View 2 Replies
Was driving on the highway and all of a sudden my mph gauge just drops and my car slows down. This is the first time it happened and it didn't do it again after I got off the highway. Other things it has been doing: eating gas, shifting hard, and doesn't want to get up to speed. Not sure if they are related to this new problem or not.
View 2 Replies
