Phaeton :: Won't Start After Filling - Evap Purge Valve?
Nov 23, 2014
I have difficulty starting after I fill the tank (usually to about 3/4 fill, not topping off.)
I searched the forums and noticed the evap. system N-80 purge valve may be the culprit. Other VW's have the issue including one thread on a Touareg.
I think I'm the first with this issue on a Phaeton. Sometimes getting loose gas cap faults too and on occasion a CEL. I had a fuel pump replaced last week, but this problem predates the pump failure.
Does this sound like the issue here? Doesn't it throw a code? I'm wondering why they didn't discover it when the diag'ed the bad fuel pump.
View 6 Replies
Advertisement
I have a 2001 saturn l200 2.2... Well I put the new EVAP Purge Valve in last night.. Today I start the car and started to clicking so I unplug the new EVAP Purge Valve and it stop clicking and i plug it back in and started clicking..
View 6 Replies
I only have 2200 miles on my new 2012 Passat SE V6 and the check engine light came on the other morning. I took it in to the dealer and they found codes P0442 (EVAP Emission Control System Small Leak Detected) and P0456 (EVAP Emission Control System Very Small Leak Detected). The tech says on the work order that he removed and tested the EVAP Purge Valve with a vacuum pump and the valve would not hold a vacuum. The dealer replaced the EVAP Purge Valve under warranty. They say this is the first 2012 passat V6 they've seen with this issue. I've only had the car for 4 weeks.
View 5 Replies
Where are the canister and solenoid valve located, above the tank? 2009 Sonata 2.4L ....
View 1 Replies
Replacing part 9C915 ?
"CODE P0443 canister purge fault" diagnosed....
Found: EVAP PURGE FLOW VALVE STICKING
Recommending: "Diag, Replace sensor then retest" ....
They want to install a new 9C915 which they called in hand writing a Canister purge sensor but I've seen it called a canister purge valve on another thread by FIREME who puts 9C915 as "toward the driver's headlight assembly, near the radiator. You'll need an 8mm socket to remove it"...
3.0L DURATEC FFV V6 ENGINE
From the "newly washed ashore" who's now double posting after being flogged for trying to keep this info in a single thread rather than spreading it all over the place...
View 1 Replies
Have a 2012 gas powered Escape XLT, 2.5L 4 cylinder.
I need to replace the evap purge valve. Looking at youtube videos and from other posts it seems easy to replace. My problem is where is it located on this Escape?
Is it under the hood or underneath the driver's side? This is just the valve mind you, not the canister in the back.
View 3 Replies
Where the EVAP canister purge solenoid is located on a 1999 Ford Windstar with the 3.8 engine?? I replaced the vent valve that is located on the canister itself but cannot locate the purge solenoid valve.
View 2 Replies
Just received a P0441 CEL (Evap Emission System Incorrect Purge Flow). I have a 2.7l engine, 2WD. I've read other forums and it seems it's most likely the purge valve or charcoal canister.
View 7 Replies
I've had the check engine light come on and was told it was probably from topping up too much and that it would go off on it's own... I should say I have no issues with idle or rough starts.
I had it scanned at Auto Zone. The print out shows: "EVAP emission system incorrect purge flow probable cause
1) Faulty purge control solenoid
2) Faulty vent solenoid
3) Blocked vapor canister
Previous posts suggest if it were a blocked vapor canister I'd have trouble completely filling the tank so I am hoping it's one of the others. Almost everything I see suggests the purge control and that looks like an easy fix. My concerns are a) if it is the vent solenoid - how hard is that to get at and b) what is the part number as I can't find it listed anywhere? I want to have both on hand before I start trying to fix this. Lastly if it is the vent solenoid should I just give up and see a dealer??
View 3 Replies
The purge valve keep clicking means it is fail?
View 2 Replies
My 06 accent GLS has become difficult to start only after refueling, which I'm guessing is related to a bad purge control valve from what I've read. Where exactly is the valve located, and is this something that someone with relatively little automotive repair experience could do on their own? I think I've located it on the backside of the engine near the air intake.
View 2 Replies
Looking for the location of purge valve on a 2003 aviator ?
View 8 Replies
I recently got a check engine light. I went and got it checked, the person said its the canister purge valve that needs to be replaced. Where it is located and the difficulty replacing it. The part is cheap and I want to replace it this weekend. 2007 elantra
View 2 Replies
2006 Honda Element 2.4 ... I developed an unknown bad oil leak. Low oil indicator light did not come on. Highway drove it down to one qt. Now blowing blue smoke and lost power. Why my oil light did not come on?
Also, I have needed a purge control valve for quite some time. Could this of caused the oil leak?
View 2 Replies
I just had my 3rd Canister purge valve installed a month and a half ago, and it's already dead.
I noticed while I was driving that it was constantly pulsing after the engine warmed up, and continued to do so as long as I was driving.** This did not seem normal to me (I can hear it in the cab).
The solenoid is burning up and measures open circuit. No codes are thrown during the time it continues to pulse, but when it burned up again, the 3 codes (P0441 Incorrect Purge Flow, P0440 Solenoid Failure, P0443 Purge Valve Circuit Trouble) are immediately thrown? indicating the solenoid is fried.
The system runs a series of tests during normal operation, so if there was a problem with an actual leak or clog, it should show up as a test failure code, but does not. My inclination is that the problem is a sensor.
View 6 Replies
Engine light came on a week ago, finally made it in to get the code pulled yesterday : P0441
From reading on this site, thinking its a faulty purge valve.
I have found pics of its location on an 04, but cant seem to find it on my 08 2.7L.
View 14 Replies
So sometime last week my check engine light came on. Took my 13 Accent to the dealership and they said the purge valve is to be replaced. Now my Accent pings when running 87 gas and I read that others (not necessarily Accent owners) who changed their purge valve noticed the pinging go away.
View 5 Replies
My Ex is throwing a P1451 Canister Vent Purge valve issue. Is the canister for the Ex hidden on the frame above the gas tank? I looked around the frame in the back of the truck but am having no luck finding it so I'm guessing ill have to drop the tank to get to it. I've read that wire chafing for this valve could be the problem.
View 3 Replies
I have a 06 Elantra having a problem with a p0441 code flow fault I changed purge valve and canister purge valve I don't know what else to do what else can I do to get it to go away permanent so I can get car inspected no codes for my car can be on but only 1 i/m
View 3 Replies
I need the PCM pinout for a 2002 F150 4.6 For the Purge Control Valve Circuit. If possible the wire schematic would be nice also. Getting code PO443 (( hard code )) I have checked battery voltage at valve connector with key on (( 12.2 volts )) valve resistance is at be 35 ohms so I'm thinking I may have a bad wire or a bad PCM .
View 2 Replies
CEL turned on this morning heading to work. Truck drove completely normal with no signs of altered performance.
Stopped by Autozone after work and they checked it with a code reader.
Came back with P0442 - "Purge Valve Solenoid"
Part sold with or without bracket.
Is this a common part to fail? How can I be sure it has truly failed? Is it acceptable to reset CEL and see if it fails again? If so, how do I reset? Where is part located?
View 14 Replies
