Phaeton :: V8 Starts Fine But Stalls And Dies After 15 Seconds
May 18, 2010
I am working on my father's boss' 2004 Phaeton V8. The car usually sits on the weekends. What it is doing is, it will start and run smooth, but after 15 seconds, on the dot, it stalls and dies. It sounds like it is starving for fuel.
What I have done so far:
LH intake actuator arm found broken, replaced both with "Gruvenparts"
Checked all fuses and relays
LH fuel pump reads 14 volts until the relay kicks it off
Tested fuel pressure-good
Batteries fully charged
LH fuel pump reads 0.7 ohms w/key off
RH fuel pump reads 6.0 M-ohms when first connected and gradually climbs to 31.5 M-ohms
(I assumed this meant RH pump was bad and so I pulled it out and bench-tested. Ran perfect and tested at 0.7 ohms out of the car)
Re-assembled everything to pull the car out of the shop, and wouldn't you know it started and ran like normal.
Road-tested for 2 hours the next day without any problems.
So, I call the customer to pick it up and he says he will be there 2 days later.
View 15 Replies
Advertisement
I have an 04 w12 with 80k miles on it. It will start fine but will not run for more than 10 seconds. As it idles down from startup it settles to about 700 RPM's where it normally does then dies. If u drive it it will start and go into gear fine as u go to pull away it loses all power and dies. I have checked the minor things i know like air filters, oil, tranny juice all appears normal. New batteries less than 3 months ago also.
View 11 Replies
A few days ago, I went to start the car, and it will start, and idle fine for a few seconds, and then begin to run crappy, idle down, and die. I tried starting it, and giving it some accelerator pedal, and it dies. I changed the timing belt, idler pulley, and tensioner this summer, so I'm ruling out a bad timing belt. There is no check engine light, and I replaced the plug wires because when I removed the cover, I noticed one of them was worn in a spot, and the wire shielding inside the rubber insulation was visible.
View 11 Replies
So, this morning I stopped at the grocery store and when I came back out I started my car. The car ran for about 20 seconds then stalled. Luckily I was able to get the car to the other end of the parking lot for a tow truck yes, this meant starting it about 6 times! This is the second problem in 12 years of owning vw's I'd say that's a good track record! I did a complete auto scan.
View 20 Replies
I have a V6 with 162,000 miles. A year ago in the early spring we replaced the alternator, starter, fuel pump, lines, filter, dropped and cleaned the tank, fuel coils, repaired / replaced almost all injectors, spark plugs.Since April of last year, every few months my Car would have a hiccup of that it starts fine but would immediately die out. It would take anywhere from 5 to 30 minutes of trying to get it to start again. Other than that it would run beautifully. This week, while on the road it would jolt and die out. It happened 3 times. Yesterday morning it would once again crank fine and immediately die out. It will no longer keep running. We have not been able to keep my car started since then.
View 14 Replies
I've been having some issues with my mk4 R32. Right now i'm leaning toward changing the fuel pump and filter but i want to be sure before i do.....
Problem: I've been daily driving my r32 to work for the past couple weeks and about once a week it will start, idle for a couple seconds and then just bog out and die. no codes, just idle, then chugging and dying. it will fire with some starter fluid and will sometimes hold a very sickly idle but most the time will just run the starter fluid out. the weird thing is is that it's intermittent and will happen randomly and if i leave it overnight or sitting for a couple hours it will fire up like nothing was wrong. i just wanted some input on what it might be before i replace the pump. i have already done the relay so its not that.... the only code that it has ever thrown while i have owned it was for the intake changeover valve (N156) which i cleared and it hasnt yet to come up again.....
View 14 Replies
Our car starts, then dies. It starts fine, then dies. This only happens in warm weather, which we have finally been experiencing in Northern Illinois. It eventually gets to the point where we can drive it, but then might die at a stop sign, or it can go the rest of the day and not have any difficulties. I know later models have timing chains, not belts. Does our car have a timing belt problem or maybe fuel pump? And why only in warm weather?
View 7 Replies
Having some problems with my 92 Nissan NX2000. i just finished changing the clutch on the car now its acting horrible.
When i start the car, it will run decent for like 2 or 3 seconds then the idle drops down till it almost dies, catches itself, idle goes up to about 500 were it will pulse around for a few seconds until it dies. If i rev it it will stay running, kept it running for about 2 mins. but as soon as i let off it will pulse at 500 until it dies
After i changed the clutch it started up fine, it ran great for about 20 seconds before it just died. when i started it after is when the problem arose.
I took a video of the car running, which can be seen here. [URL] .... (It has never caught itself like that before and jumped up to 1000 rpms before. It normally will die at that point)
The video is really quiet, not sure what happened there. if need be i can get a video of the engine bay so its louder, was mainly focused on the RPMs.
Here's a few things i tried: Checked fuses, Changed spark plug wires, made sure they were all seated good, MAF wires were rubbed a bit so i cut the MAF pigtail off one of my other sentras and soldered it on,Changed to a good battery, Changed fuel filter, Added more gas (in cause gauge is broken), Made sure all connectors are plugged in, Checked around for vacuum leaks, found that one of the large hoses coming off the intake going to the engine had separated so i plugged them back in and nothing.
View 4 Replies
I've shipped my R32 back to the UK, the combination of cold and damp weather has taken it's toll on my car. I started it up Saturday and left it ticking over to allow it to warm up before driving it. The car is used to Houston heat, so a few minutes running will allow the oil to warm a little as the weather here is around 40F at the moment. The car ran for 5 or so minutes, then stalled.
The car starts to about 3 seconds, then dies. I have checked VAGCOM, the only fault is a steering wheel sensor (?). It has a full belly of Shell 99 RON fuel and was serviced just before if left the USA in October.
I have had it towed to the local dealer for repair. I have tried disconnecting the battery for 30 mins to reset the car, it didn't make any difference. I have also tried another key in case it's s sync problem.
View 10 Replies
Today I acquired a 1982 F150 with a 302 engine, 4 brl. Edelbrock carb. The truck starts and idles just fine, but when I come to a stop, try to give it gas to go it dies. It starts right back up, and I have to rev it high a couple of times then put it in gear and it will finally go. When I got it home I let it idle a few minutes and tried playing with the air and fuel mix but don't know what I'm doing, really. It seems I can hear a hiss, and when I was reaching for the air/fuel screws I got a little shock on the hand from the distributor. We want to use this truck as a farm truck, and plan to get a manual for it, but what might I might check for the cause of it stalling.
View 1 Replies
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
View 14 Replies
So i start my car and it starts easy but after a few seconds it dies. I can get it to keep running by changing the fuel mixture but then it has no throttle and it will die if i try to use the throttle. It is 1985 VW Jetta engine in a 1981 Scirocco
View 2 Replies
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....
View 2 Replies
Car has 6600 miles on it and is back in the shop for 2nd time to determine what is wrong. Basically, the car starts and then stalls out after a few seconds. It will not start again (at least with me). Course, the dealer can get it started after the tow to them.It began in April after an oil change at the dealer. A week after the change, it started up and then a message SHUT DOWN appeared on the dash.
The car stalled and would not restart. When it was towed to the dealer, it had no oil. Per the dealer, there was no leak and it was assumed the tech forgot to put oil in it, They indicated it was not a problem since there was some oil remaining but the car would still not start. They kept it a few days and replaced the relay for the fuel modulator, electronic fuel pump, fuel unit, fuel pump control unit, e-control unit and of course the battery. Note: this was a cold start.
About a month later, I had driven the car for about 30 minutes, left it for an hour and came back to the car.....it stalled again right after start up and would not restart. After being on hold with roadside assistance for awhile, I tried it again and it started without issue. .
A week later (today), used it for a half hour, came back to use it 3 hours later and same story. Started, then stalled, no restart. Towed it to the dealer and the tech got it started but no codes telling him what is wrong.
View 5 Replies
I have been suffering from LH battery drain for some time now. sometimes its random I will park it for 10 min. come back and the battery is drained (I have to use the key to gain entry). sometimes it only happens over night, where other times the battery doesn't go dead overnight. so last weekend I decided to change the brakes...That was easy but then I forgot to hook up my battery maintainer...so you know what happened! now the problem is I charged the battery and hooked it back up. No start! everything works fine the battery is fully charged and only 1 year old.
But this is the weird part if I disconnect the starter battery the car starts up fine. I hook both batteries back up and try the parallel start way (turn to start then full counter clockwise then full clockwise several times no luck). the LH battery is drained now after a few start and stops (no driving) and the starter battery is fully charged. but with both batteries hooked up it wont even attempt to start and now I also have no power to the power trunk!!! this car is starting to suck balls.
View 12 Replies
2006 ... HV battery changed over 4 months ago and car ran fine until last week when the car just stopped and won't get ready. Before that incident, the vehicle was running fine all day, while he was returning from the days chores in the evening, it just stopped, dashboard all lit up. After a while, the car started again, and he was able to move it away to the side of the road...just about 2 meters and it stopped again.
View 15 Replies
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 Replies
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
View 8 Replies
I'm driving a 95 buick lesabre, good condition, clean, 130k miles on it. 2 months ago the car started stalling and then it died. Took it to a shop, replaced all original fuel pump and fuel lines. Repeat this about 3 more times, all in all, the fuel pump, fuel lines, map sensor, mass airflow sensor have been replaced. Yesterday, the same thing happened. Took it to a different mechanic, he says he drove it for two days and couldn't find anything wrong with it. Is there anything specific in a 95 lesabre that could be causing this? It drives fine for a while, and then out of nowhere it starts to stall, then the car dies and check engine light comes on. Gas is kept above half a tank due to winter conditions and the fact that it's an old car.
View 8 Replies
2010 Cobalt, LS 2.2 Ecotec, with 13.7k miles. Oil level normal and battery voltage = 12.5V.
I've bought the car new in Feb. 2001. Car started and ran normally for the work commute on Friday, 9/2. Today the Cobalt starts normally, runs for 2-3 seconds, and then stalls. The accelerator has no effect. It's already been towed to the dealer..
View 1 Replies
Went to start this 5.0 TC after it sat idle for a week, and it died within 3-4 seconds. Further attempts resulted in similar response. After some initial checks, I was able to keep the engine running by manually depressing the IAC plunger into the barrel. The engine ran fine as long as I could hold that, but stall immediately after release. Codes: TPS out of range; HEGO HO2S sensor out of range-always lean. Bought a new TPS no change.
Today: With the key "on" and engine off, the fuel pressure is a steady 38psi. There is an air release button on the fuel gauge line and when I pushed that, the gauge pressure dropped to zero and does not come back (until you key off and on again). I removed the IAC from its mount and with the key on--I observed the plunger move inside its body--guessing maybe 1/4 inch. I casually checked all the engine management items I see in books and looked at vacuum hoses and couldn't see anything amiss (also climbed on top of this engine and checked the rear--PCV lines etc.). I removed the fuel regulator vac line and observed no fuel leakage there.
View 1 Replies
