Today after leaving office I switched on the ignition and for the first time I see this massage "Immobilizer activated". I went out to look at the car and found some finger prints on the driver side window.
Is the car so sensitive to touch? Or the alarm was activated for some reason and some one tried to look inside the car?
I have problem in my VW Passat v6 2002. When insert car key to turn on start Engine, The screen shows an error message: "immobil activated" That means: Immobilizer is activated! And after that car is auto turn off then the Engine shut down in one second with flashing key light! As the fuel tank is empty..
But When I try to start again after an hour / two hours it's works!! This situation comes up if the car was parked from last night until the moment of start on in the afternoon!!! What is strange that this problem does not occur only at the time of day warm, Between 5 and 11 o'clock in the afternoon hot days!!! Because this problem is not never happen in the evening and night.
I go to the Workshop for dellership Car Agency. They re-programmable keys, But the problem is still continuing.
Have a problem starting Mk7 gti. My car won't start or shuts down and get a message in the display says immobilizer active. Had it towed to the dealer sat overnight and problem started up the next day. They drove it around most of the day and when I picked it up it wouldn't stay started or start and same message on the display came up.
View 4 RepliesOur Phaeton has a had a problem with the radar unit and was the electronics where repaired. According to the repair people it now has to we reactivated in the car but we are not managing to achieve this with VCDS. We have tried the following codes:
Code:
Select 01 (Engine Electronics)Security Access -> Function 11 (Codierung II) ACC = Adaptive Cruise ControlCCS = Cruise Control System (Normaler Tempomat) ACC/CCS-Deactivation Code: 16167 (first deactivate, than continue)ACC-Activation Code: 13647 (Possible also 13377 or 30903)CCS-Activation Code: 11463
The codes are accepted by VCDS, but nothing changes.
Also, additionally the warning for engine fault has gone on. Is it possible to disable this warning? We tried code 30903 but it isn't accepted.
[Code] ....
On Friday, all of a sudden I found that I could not use the keyless feature to lock/unlock my car anymore, and when I tried to start the car with the push button, it showed "key not found" "immobilizer activated". By that time, i still could use the remote key to lock and unlock the car, and start up the car with the key blade. After I drove and parked the car, I went to get a new battery for my key because I thought my battery was giving me the trouble. Then I went back to the car, I was still able to lock and unlock the car with the remote buttons, but I cannot start up the car, even with the key blade. So I disconnected both battery, waited and reconnected them, the car is able to start with the key blade, but can no longer lock and unlock with the remote buttons. So I can only lock the car manually now.
Later, I scanned the car, found there are 2 faults. One is an old fault, which is "the antenna in rear bumper has no signal intermittently", and the new fault is "luggage compartment start/access authorization antenna upper limit exceeded", and gave me a time that this occurred, which is exactly when I first found the keyless entry didn't work on Friday.
Recently, I've noticed that sometimes my driver's seat gets hot, even though the switch is in the cooling mode. I had gotten in the habit of turning the switch back to the detent "0" setting, and then put it back into the cooling mode (-1 to -3) and all would work well again. However, yesterday, that little trick didn't seem to work and so it seems my seat heater is being activated even when the switch is supposed to be telling it only to run the seat ventilation fan. Is it likely just a failing switch?
View 24 RepliesI have since purchase of the car for 9 months ago enjoyed the use of the rsap functionality with my S6 connected over the Bluetooth.
Now without any knowable change of settings or update or hardware I got a no network message after connecting to the car.
The phone and the car are still connecting over BT and the phonebook is transferred and all the adjustments within DIS are working as before, I can even make a call but without connection to a network it won't work.
I know GP2s rsap is restricted to 2G networks and if I search networks manually with DIS , the car finds 2 of them, but can not connect none of them.
My service provider Comviq is telling me that there has not been any changes on the SIM card accessibility or newly implemented improvements or updates to Android.
They could anyhow confirm the 2G net being rather weak in the area and this could be the possible reason.
This morning when I went to start my car i got a Service Now message. Once the car was started it went off and didn't come back on. I have no warning lights present on the dash what so ever. I've never seen this before.
What does it mean? I have an 04 W12 with 60,120 miles. BTW I've had all service work done for the 60,000 service. Car is beyond up to date with it's service.
Lately I've been getting the Stop! Car too low! message when I start the car if it has been sitting more than 6 hours or so. the front appears to be too low. After 20-30 seconds, the front end raises up high enough and the message goes away. It didn't do this when I first got the car. I'm going in for my 80,000 mile service soon.
View 17 RepliesAfter 3 trouble free years my car had a different TPMS problem, with TPMS FAULT message popping up. The dealer initially changed one or two sensors and then the most updated module. For 1 day there were no problems and while driving on the highway the malfunction warning came up again. Now they are suggesting it could be related to the tires that are not the original ones, but same size and specs and I have been driving on them for a year without any problems.
View 4 RepliesToday I had been driving about ten minutes when I got a "Check Gas Cap" warning, inclusive of beep and appropriate icon. Pulled over, switched off but left key in (this is equivalent to a warm boot in my experience), opened gas cap and closed again (it was fine). Turned engine on, got same message, remained on until destination (approximately 20 minute drive). Parked and locked car for approximately 2 hours (equivalent to a cold boot). When I turned on the engine again, the message was gone, and remained off for the rest of the day.
The car had been sitting unused in a heated garage for a little over two weeks, and the weather today was nice, sunny, a few degrees above freezing.
In my view, it clearly was not related to the classic "fuel cap not tight enough" problem of modern cars: for one, I had not just refueled (in fact, I have a little over half a tank). Also, I always tighten the cap until I hear at least a few clicks. SO I wonder if it might be an early warning that my maintenance battery is getting weak, i.e. spurious error message triggered by low voltage?
I haven't been able to find a discussion about failure or replacement of the oil level sensor. I'm getting a error message displayed each time I start the car. I took it into the dealer for an oil change. After they completed the change, they recommended replacing the sensor. I'm inclined to wait another 5k for the next service to do that. Diagnostics did not show any error codes. Doesn't make sense to me. just replace the sensor...
View 7 RepliesWhen I park my car and shift the selector into "P" the car will not allow me to remove the key until I jiggle the selector. I get a "please shift the selector into P"
After it's jiggled it unlocks, and I can then remove the key. I would prefer to fix it myself, rather than take it to the dealership.
I am having some difficulties with the stereo in my 03 W12.
Suddenly it stopped working.
When i press the cd button - I get a message that says that there is no cd player avaliable. When i press the radio button - I cant see any stations and there is no sound.
Today I received a message on the MFI telling me that the coolant was overheating. My better judgement told me to immediately pull over at the next available spot to turn off the car since the coolant temp gauge was almost at 280. This is well over the 200 where it usually resides. However, the oil temp gauge was right at 200 which is normal.
Perplexed, I called my dealer. The Phaeton Tech was gone for the day so they suggested that I have the car towed in for inspection. Knowing the temperament of the Phaeton (2004 V8), I chose to restart after about 5 minutes. At that point, everything was reading fine & I drove home (about 20 minutes). I ran a VAG-COM scan to see if anything would come up, but nothing did.
I'm getting a service now message on my display but no other warnings. Why this would be coming on?
View 7 RepliesWhat does this message mean? ELECTRICAL CONSUMERS ARE BEING SHUT DOWN....
View 3 RepliesWhat does it mean when the PRND2 area all illuminated at the same time? Normally only the gear selected will be illuminated, but yesteday I got a solid bar illuminating all the gear selections. Couldn't find any reference to it in the manual. Shut the car off and restarted and the problem went away.
View 24 RepliesI have 2004 V8 Phaeton ,the message LEVEL FAULT WORKSHOP. keeps appearing ,then disappearing, sometimes it will stay until the car is turned off,. When it comes some times even on long highway journeys I wont see it at all!. When it comes on nothing seems to change.
View 6 RepliesCame back from car wash (probably no significance) pulled in garage turned off ignition and the title message came up in the center display. Car will not start. At this point I have no Vag Com and the car will not start.
View 2 RepliesI started back up again and 10 seconds later it came back on, but then went away for the rest of the 30-minute commute. Went out during lunch today and there's no message.
I'm gonna do a vagcom scan when i get home, but wanted to know if there's any history of brake fluid leaking and needing to be topped of.