Phaeton :: Getting A Fault For A Misfire Cylinder 3
Apr 13, 2013
She is really running rough. Vcds engine scan shows no value on bank2 of the O2 sensor or lambda once I drill down into things. I haven't been able to figure out much else. Also I was getting a fault for a misfire cylinder 3 so I replaced all the coils on that side of the engine and put in a new set of spark plugs all around which did improve things but the car is gutless from idle to around 2000 rpm then it starts to pull. The check engine light blinks for about 30 seconds and then comes on steady. I used a propane tank to try and find any vacuum leaks but everything looks good so far. I guess I will take it to my independent shop hoping his scan can shed some more info on the O2 sensor readings.
View 2 Replies
Advertisement
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently got the P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. Any clues to the cause of my problem?
View 5 Replies
We got our latest Santa Fe computer email and it warned of an engine fault. The car itself was not flashing any warnings though. Took it to the dealer and they said OBD was throwing a P0303 cylinder 3 misfire code. They shifted the ignition coil, and replaced the injector and seal before resetting the code. They had the car for 3 days though. Car was not running rough or anything else you would expect from this type of issue. Still trying to figure out why we got the email with no indication of trouble from the car itself.
View 3 Replies
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 Replies
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 Replies
06 F150 fx4 has cly 7 miss fire cly 6 has oil on plug .Check engine light comes on only if you step into the gas, The oil was low. If you drive normal the check engine light does not come on, but you can fill the miss when in gear. Change the plugs an coil add oil still no change.
View 4 Replies
All of all sudden, my car is complaining a airbag fault, VCDS scan fault code as below, Does it mean all 10 airbags in my Phaeton is no longer working ?!
Address 15: Airbags
Labels: 3D0-909-601.lbl
Part No: 3D0 909 601 E
Component: 0G Airbag 8.4E+ H10 0934
Coding: 0012359
[Code] ....
View 3 Replies
I just got the Air Bag Fault light and warning on my display for my 2006 Phaeton. I have not seen any posts on this topic doing a keyword search. This happened the day after I got back to my car at the airport parking and found a cracked windshield that is $825 for the glass alone. Not a good week so far.
View 9 Replies
A few days ago I got an Airbag Fault Warning while driving, since then the orange airbag light has remained on and at start up it gives me a "Airbag Fault" warning. Any remedies? The manual states to just take it in to the dealer.
View 7 Replies
I recently had my front axles replaced and a week or two after I'm getting this code for level fault workshop. Do you think it could be something they did when they replaced the axles. I also had the secondary radiator replaced.
View 11 Replies
Just reporting following problem that seems to affect most VW TDI engines with DPF - I have just experienced it on my Phaeton - basically as you accelerate you get the engine fault - workshop warning with a flashing coil (glow plug heater lamp) - this is accompanied with reduced performance (no Turbo) in a protect mode, stopping and restarting the engine clears this temporarily. the MIL eventually stays on (performance unaffected until next time the dreaded engine fault appears) - It's a bit scary and if you go to the dealership, they will try to convince you that you need a new sensor and DPF and estimate a cost of 1.5k plus)
I can recommend RD garage services in Shepperton (Richard is an ex VW Phaeton and Touareg Specialist) Richard changed the sensor and performed a forced regen cleared all of the fault codes (the gearbox had even gone into a performance limiting mode due to the faulty exist pressure sensor). All is now well car back to pulling like a train and back to mid 40's mpg on a run.
View 10 Replies
So my car wouldn't start after work. I went and replaced the starter battery and no problems. I come home and won't start again. Both batteries are good but now I get a message, system fault workshop vw phaeton And key pic comes on screen.
View 11 Replies
My check engine light came on over the weekend. It was not blinking so I am hoping for just a sensor fault or some other inexpensive issue. I am trying to remain hopeful but after having to replace 2 coils and both catalytic converters about 40K miles ago I am really nervous...
I took the car to the shop this morning for diags but what might be causing the problem? It is a 2004 V8 with about 142K miles.
View 2 Replies
My 2006 W12 has been trouble free since taking delivery over a year and a half and 30K miles ago. Just broke 60K total miles over the weekend and the engine light came on. I have pasted the scan below. I cleared the codes and drove about 500 miles before the MIL reappeared. I have read this thread: [URL] ....
My first question is: Is there any harm in continuing to drive it?
I have visually inspected the secondary air injection system hoses and can't find anything glaring (no kinks, leaks, disconnections). I am open to taking the car to the dealership but I have low confidence in their diagnostic capabilities. I am fine with them doing work once we know what is wrong but I want to tell them what to do (replace a bunch of hoses for example). How to proceed?
Address 01: Engine Labels: 07C-906-018-BAP1.lbl
Part No SW: 07C 906 018 AJ HW: 000 000 000 00
Component: D1-6.0L-AT-LEV2 G 6722
Revision: --H01--- Serial number: VWZ3Z0E5400307
Coding: 0000173
[Code] ....
View 19 Replies
I have 2004 V8 Phaeton ,the message LEVEL FAULT WORKSHOP. keeps appearing ,then disappearing, sometimes it will stay until the car is turned off,. When it comes some times even on long highway journeys I wont see it at all!. When it comes on nothing seems to change.
View 6 Replies
I was queuing for the Dartford Bridge yesterday, and had been about 20 minutes in crawling traffic, when for the first time ever the DPF indicator came up on the dashboard with a message to check the manual. Then moments later I got the engine fault, workshop alarm which was quite insistent. Reaching the tolls I pulled away and then 'booted' it for a while in sport mode and both indicators disappeared...so I thought I had cleared the problem.
I reached work without incident, but then when I came to restart the car later in the morning, I had the engine fault come up again with a very insistent chime. I phoned my dealer and took it in...the DPF indicator coming up again while in traffic on the way there. The fault has been diagnosed as a faulty diesel particulate sensor, which is now being changed on Monday when the part arrives.
View 3 Replies
Noticed the vehicle was riding low on the passenger sign, and then received a fault code on the driver's screen "Level Fault Workshop" what is this? I can't find in the faq section...
View 9 Replies
My AC stopped working a few weeks back. The garage looked at it and noticed it had no refrigerant, the fault code stated this also. It was traced to the condenser which was replaced and the system regassed. The AC will still not work. The current fault code is 00716 Air Recirculation Flap Positioning Motor (v113) 005 - No or Incorrect Basic Setting/Adaptation. That is the only fault code showing and cannot be reset.
There is no cold air at all. Could this fault be preventing the AC from working? What is odd is that the compressor seems to be running when you switch on AC as it shows up in the diagnostics as running with about 2nm of torque.
View 21 Replies
I have a 2004 Phaeton which has been having multiple problems with error codes. I keep getting Level Fault Work Shop. When this code comes on the ABS and EPS also fail and can only be reset by restarting the car. My VW dealer is having significant trouble finding the problem. Thus are they have repalaced the batteries, and the control module for the ABS. I think an option could be the battery control module.
View 9 Replies
Doesn't seem to be any pattern to it, kind of random; but this message has been popping up a bit lately. Of course it never seems to do this when at the dealer for service.
View 10 Replies
OK, so I've been getting the "Tyre Pressure Monitoring System Fault" warning message repeatedly for some time now. I had the "G" code TPMS control module installed last week (under extended warranty) thinking that that should fix the fault. However, the fault continues.
Do this fault might be due to dead or dying batteries in the TPMS wheel units (not covered under extended warranty)? If not, what else could it be?
View 4 Replies
