Phaeton :: Electrical Malfunctions After Installing Stop / Start Button
Nov 11, 2009
I did the installation of the start/stop button and it works. However, I have some unresolved issues. I have done a search in the FAQ thread but could not find anything referring to the following:
1- When I lock the car, either with the fob or with the door buttons, the alarm will sound when I enter the car if I unlock it using the door handle sensors. I can disarm the alarm with the fob, but it is not disarming with the door handles. How can I solve this issue so that the alarm is disarmed with the door handles? Can this be solved using a VAG-COM?
2- When I turn on the alarm, either with the fob or the door handle, the alarm indicating light blinks for a few seconds, then goes steady, and then blinks normally. I had not noticed this steady light state before. My alarm, I think, always went straight to blinking and stayed blinking
.
3- When they gave me the car back the adviser said that the seat would not move and the trunk would not open. However, I think they ran down the battery because the interior light was on. The dash displayed the "start the car now" message.
a) I had an almost two hour drive back home, do you think that the battery recharged in that time?
b) Was there any lasting damage done to the battery?
c) Is it safe to charge the battery with a trickle charger or do I need a special and specific charger?
The trunk now operates OK and the start/stop button also works. I wish the alarm also did.
View 12 Replies
Advertisement
My power door lock switch in the drivers door stopped working (not the actuator problem, but the actual switch would unlock, but not lock the doors)
I started to research if it could just be simple corrosion and decided to spray the contacts with CRC electronics cleaner. It completely fixed it.
Next, my parking brake light sensor stopped working so I did the same and it fixed it.
I began to research cleaning contacts and found a number of people in the automotive forums who basically spray contact cleaner on every electrical connection they ever touch.
I will do this in the future. The only part I wonder about is if there is something better to spray on them to prevent further corrosion in the future. I used dielectric grease but it would be nice to just spray the thing down. However, CRC does say their electronic cleaner prevent future corrosion.
View 2 Replies
I can not start the car by pressing the Start / Stop button. The display shows the message "Key Non found". Remote control key with normally opens and closes the car but the car itself does not open the approach to it. I have two keys and the two are the same.
View 7 Replies
OK... My '00 GLX 4-motion 30v has started to really piss me off! It started about a month ago with the trunk latch. The light would come on in the dash and I'd check it and it would be open. I didn't open it! Then when I try to reclose it, no luck. Won't latch! So I look at the latch and it seems to be broken. But then I was driving down the road and the trunk just locked itself! I couldn't even get it to latch the day before and now it's locked! Next the rear view mirror decides to go all hazy and piss all over the dash! WTF! Now the autodimmer doesn't work! The rain sensing wipers quit and now the delay setting just does nothing! Then, as if that weren't enough, the A/C just decids to not work anymore! It won't turn on the compressor. It was working fine when I got to work and then when I got back in a few hours later, nothing! It has good system pressure, but it's like the controll unit isn't telling the compressor to kick! Up untill this point the only problems it's has giving me were the infamous tie rods and some wheel bearing noise from up front, oh and the camshaft seals. Starting to get pissed at the thing! Leaning toward the BMW side of things very quickly.
View 3 Replies
I have a Mini Cooper 2005. Last month the battery died. The warning sign was that when I turned the key, there was a second or two pause where everything went dead. No lights at all in cabin and clock reset. Then it started up. It did that many times before the battery went dead. I got it charged and thought all was well but now the mini did the pause thing again and I fear that I am going to deal with a dead battery again.
View 5 Replies
I have a 1995 Ford Taurus, and I just swapped in a new engine from a donor from 2000. The engine is a Flex Fuel 3.0L Vulcan OHV.I've got a wealth of background knowledge as a mechanic [5 years+] and an electrician [4 years+]I have swapped over everything required to make this work, in theory. I swapped exhaust, fuel system, and computer/harness and all the relays to go with it. I also made a custom gauge cluster from a 2000 Taurus as well.
Well everything works just peachy, all the wiring for the most part is correct minus a few buzzing relays that I just need to work out. The main issue this [now monster in my eyes] has is the PCM is not telling the FPDM to tell the Fuel Pump to start. Turn key, and no 3 second startup. I've checked the fuel pump, and it's fine. I replaced the PCM and that didn't solve it. I have the security system from the 2000 in there as well, thinking that was an issue. I also have the emission sensors and canisters installed, just like you would see in the 2000.
I'm at my wits end trying to figure out why the PCM isn't sending voltage out to the FPDM. I had to of missed something along the way but I double checked and still can't find anything. How to get this working properly.
View 17 Replies
I just bought a 97 f-150 from my dad, there are some electrical issue's but the main one seems to be battery drain.
I have noticed with the truck off key in my pocket, the a/c doors keep trying to move and the a/c head has power to it.
I know the engine has been replaced, with about 20k on it.
The temp gauge pegs w/o getting hot, and it even turned over once while we were getting in the truck. Again key in pocket.
View 1 Replies
I have a 2006 Ford F-150 V8 XLT 4x2 SuperCrew that I had to replace a few old/blown bulbs on (left Front Blinker and rear Right Blinker/Brake). I decided to go with the Pilot brand LED replacements, and verified that they are the correct replacement models to the factory bulb part numbers.
Per what I've read from others' experience doing this... I opted to buy the EP27 flasher to fix the issues with hyperflashing, rather than going with Load Resistors. So, all LEDs blink/flash with no problem.
The issue seems to be related to me having the Headlight Switch in the DRL-on position, and the headlights/parking lights not being on (i.e. if it's still daylight and it's just the DRL). If the Headlight switch is left in the off position or in the DRL-on position, when I brake or signal (left or right) the entire electrical system will flash/illuminate with the brake/flashing activity (this includes all LEDs and brake lights and the Stereo backlighting... anything that is dimmed by leaving the Headlight switch in an 'off' or DRL-on position). The only way to fix the problem is to turn the Headlight switch into the parking or headlights on position.. then the issue doesn't occur, all signal and brake light activities work as expected.
It's not a big deal, but I guess I'm lazy and like having the headlights come on and off automatically... plus, I'm a little worried that there might be an electrical issue that could cause me issues if I don't address it now.
The only thing I have NOT done is replaced the LEDs back with Incandescent bulbs, to see if the problem is totally eliminated. I have verified that no fuses are blown in the fuse panel, etc.
I'm sure the issue is easy to fix and I'm hoping the fix isn't to remove/replace the LED lights with OEM lights..
View 2 Replies
I have been having some electrical problems lately that seem to be getting worse. For the past few months sometimes when i hit a bump or pothole my radio would shut off and then turn back on. Well I never got around to looking at it cause i would forget about it until it did it again. so just a couple of days ago im coming into my driveway, hit the bump, and my car shuts off. Not like a stall, just no electricity. I was thinking i need a new battery because my lights flicker and dim when i hit my window button, or when I am just sitting at a light, sometimes my dash lights will flicker. But now I am thinking maybe I have a bad ground or something.
View 6 Replies
Today I was driving to my moms house. I had been on the road for about 2.5 hours. My ABS light came on, I didn't think anything about just figured a sensor was dirty or bad. About 30 min later the radio shut off then all the gauges bottomed out and the truck lost all power. I was able to coast/idle off the road. I called a local parts place and they had a replacement alternator for me. While I was at it I also replaced the battery. I started the truck up and hit the road again. I drove another 45min with no issues.
Does this sound right or am I missing something else?
View 1 Replies
Problem 1: Headlight switch occasionally needs to be jiggled to get headlights on.
Problem 2: Wipers only work in the "spray and wipe" mode.
My Solution: Removed dash, installed new switches, replaced dash.Result: Now the right headlight does not come on at all. Wipers STILL only work in the "Spray and wipe" mode.
Question: Where do I go from here?
View 6 Replies
My truck is a 2004 F150 XLT, 4.6L 2 wheel drive extended cab
The truck starts fine. With no lights on, heater/ac blower turned off... my turn signals and hazards work as they should.
If I turn on my headlights, I have no turn signals and the indicators on the dash are slightly lit up along with my highbeam indicators. The actual dash lights do not come on.
The blower does not work at all regardless of whether the lights are on or off. Turning the blower on immediately creates the same issue as the lights. (no turn signals, slightly lit up indicators, etc). The blower does not work on any speed. I can hear the duct work changing direction behind the dash as I move the blower selector from dash to windshield to floor, etc. I can also hear the compressor kicking on for the AC.
What I have done: I have checked all the fuses. I have attempted to remove every one of them while running to see if anything shutting off would let the blower kick on. I have unplugged the blower entirely wondering if there was a dead short. I have removed and unplugged the resistor to see if that might be an issue. I have also removed the right side kick panel and checked the ground wire there that runs to the dash. Everything so far seems to be in good order.
View 3 Replies
I have a few issues with my 05 f150 that I need to know how to fix them
-the odometer display flashes on and off, the warmer it is outside the less it stays on
-heater blower doesn't work when the switch is on number one position, works fine on other positions
-power mirrors don't work neither side
View 3 Replies
Santa Fe 2013. I bought it a few months ago and soon after a strange issue appeared from time to time. When I push the start/stop button it spins the engine but it wont start no matter how much I wait. Usually it start fine for the second time. This happens sometimes and sometimes not. About 2 months ago it didn't want to start for about 5-10 minutes no matter what I tried (push the button with the tip of the key), so I decided to go to a service station.
There they connected the car to a computer to check if there were any error codes logged. But they haven't find anything, after the second time I visited the station they replaced the battery in the key, told that maybe that was the problem.
I really don't know much about cars but it was a strange idea as I would expect the same behaviour when the battery is low than when the key is not present: Car not doing anything but displaying a message that the key is not present.
Anyway, it kinda worked, or I was lucky. For more than a month everything was fine, not a single issue. And today morning it started again. I brought my car to a hand washing, and after they cleaned the outside with steam they wanted to park the car inside the building to clean the interior, and the same issue occurred. And after that it happened with me as well several times this day.
View 21 Replies
On the wiring diagram, it looks like the ground point 397 should be the one right next to the Kessy module. The one by the heater should be ground point 634. Does it matter or am I wrong?
[IMG][/IMG]....
View 1 Replies
i have a 2000 ex,6.8 4x4.every now and then the dome light stays on.theres also a problem where theres a buzzing sound coming under dash while driving and makes the dome light flicker.these are seprate problems.lol.when the buzzing sound is present ,it stops when i open the door,running or not.but starts up again when i close it,even happens occasionaly when ignition is off and no key in ignition.electrical problems are my worst night mare!!!!!!!! My battery is dead in the morning when this is happening .oh yea,and the o.d.light flashes occasionaly as well.im totally lost.
View 6 Replies
Today while hanging out in my gt,i I turned on the stereo using the button wheel on the console. I tried to connect my phone using Bluetooth and noticed that it was grayed out and not an option as an input. I noticed pressing the start/stop ignition button was the only way to get the Bluetooth to connect to the car. Im not sure if the Bluetooth is powered separately or I'm doing it wrong. I just wanna use my phone and listen to music without turning on all the lights and car electronics.
View 3 Replies
I just recently purchased a 2013 Elantra Coupe, and the Engine Start Stop button will not light up anymore. The small LED above the "Engine Start Stop" lettering still lights up blue or amber if it's in ACC or ON mode, but the lettering itself no longer lights up.
I'm not sure if it's supposed to stay lit while driving, but I noticed it started to flicker at various rates, and then eventually it stayed lit. Now, it's not lighting up at all. I'm wondering if there's a fuse anywhere that could be associated with this or anything I could check myself before taking it to the dealer. I haven't had a single issue getting the car to start with the button, just wondering what could be causing the lettering on it to not light up any longer.
View 1 Replies
I have a gen2 2007 prius (right hand drive). Problem I am having is [INTERMITTENT]when pressing the ignition button to turn off the car. When I press the button the system completely shuts down instantly and rather roughly and nothing is active (the Key is still in). I then remove the key and the system starts up! I then press the button to stop the system, put the key back in and restart it. It then works fine - until the next time. Clock resets itself as does the climate controls. Not sure what to make of this. I have just recently replaced the 12v battery in the boot.
PS. Forgot to mention that when the system goes dead, if I fold down back seat and thump the floor panel above the battery under the seat the system goes on?? Any clues. Will take it to mechanic as soon as he gets back from holiday!
View 3 Replies
Lately I've been getting the Stop! Car too low! message when I start the car if it has been sitting more than 6 hours or so. the front appears to be too low. After 20-30 seconds, the front end raises up high enough and the message goes away. It didn't do this when I first got the car. I'm going in for my 80,000 mile service soon.
View 17 Replies
I have a question, regarding the 5.0 v10. When i accelerate from stop, it has a delay, and a slow start, something like it would start in 2nd gear, but it doesn't (it's in 1st). Is the torque somehow limited whet accelerating from a complete stop? Because while driving, the acceleration is instant, and drives normally.
View 9 Replies
